background image
US Model
Canadian Model
SLV-662HF/679HF
PX Model
SLV-679HF
SERVICE MANUAL
VIDEO CASSETTE RECORDER
MICROFILM
S MECHANISM
SLV-662HF/679HF
RMT-V266
Refer to the SERVICE MANUAL of VHS
MECHANICAL ADJUSTMENT
for
MECHANICAL ADJUSTMENTS. (9-921-647-11)
SPECIFICATIONS
Photo: SLV-679HF
RMT-V266
G
j


background image
-- 2 --
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE WITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the line cord for cracks and abrasion.
Recommend the replacement of any such line cord to the
customer.
6.
Check the B+ voltage to see it is at the values specified.
7.
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5mA (500 microampers).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
TW-540A. Follow the manufacturers' instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication
is 0.75V, so analog meters must have an accurate low voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15
µF
1.5 k
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.


background image
-- 3 --
TABLE OF CONTENTS
SERVICE NOTE
1.
ERROR CODE INDICATION ··········································· 4
1.
GENERAL
Index to parts and controls ························································ 1-1
Step 1 Unpacking ······································································ 1-2
Step 2 Setting up the remote commander ·································· 1-2
Step 3 Hookups ········································································· 1-3
Selecting a language ·································································· 1-7
Setting the clock ········································································ 1-7
Presetting channels ···································································· 1-9
Setting up the VCR Plus+ system ············································ 1-11
Playing a tape ·········································································· 1-12
Recording TV programs ·························································· 1-13
Recording TV programs using the VCR Plus+ system ··········· 1-13
Setting the timer manually ······················································ 1-14
Playing/searching at various speeds ········································ 1-15
Setting the recording duration time ········································· 1-15
Checking/changing/canceling timer settings ··························· 1-16
Recording stereo and bilingual programs ································ 1-16
Adjusting the picture ······························································· 1-17
Changing menu options ··························································· 1-17
Editing with another VCR ······················································· 1-17
General setup information ······················································· 1-18
Troubleshooting ······································································· 1-18
2.
DISASSEMBLY
2-1.
UPPER CASE, PANEL BLOCK ASSEMBLY ·················· 1
2-2.
DS-84 BOARD ··································································· 1
2-3.
REAR PANEL ···································································· 2
2-4.
MA-341 BOARD ······························································· 2
2-5.
MECHANISM DECK ························································ 3
2-6.
INTERNAL VIEWS ··························································· 4
2-7.
CIRCUIT BOARDS LOCATION ······································ 5
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM ···································· 3-1
3-2.
VIDEO BLOCK DIAGRAM ·········································· 3-3
3-3.
SERVO/SYSTEM CONTROL BLOCK DIAGRAM ····· 3-5
3-4.
AUDIO/TUNER BLOCK DIAGRAM ··························· 3-7
3-5.
POWER BLOCK DIAGRAM ········································· 3-9
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM ································ 4-3
4-2.
PRINTED WIRING BOARDS AND SCHEMATIC
DIAGRAMS ···································································· 4-5
· MA-341(1/7) (VIDEO)
SCHEMATIC DIAGRAMS ······················· 4-5
· MA-341(2/7) (AUDIO)
SCHEMATIC DIAGRAMS ······················· 4-7
· MA-341(3/7) (SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAMS ······················· 4-9
· MA-341(4/7) (AUDIO PROCESS)
SCHEMATIC DIAGRAMS ····················· 4-11
· MA-341(5/7) (TUNER)
SCHEMATIC DIAGRAMS ····················· 4-13
· MA-341(6/7) (MODE CONTROL)
SCHEMATIC DIAGRAMS ····················· 4-15
· MA-341(7/7) (POWER SUPPLY)
SCHEMATIC DIAGRAMS ····················· 4-17
· MA-341 (VIDEO, AUDIO, SERVO/SYSTEM
CONTROL, TUNER, POWER SUPPLY)
PRINTED WIRING BOARD ·················· 4-19
· DS-84 (TAPE OPARATION)
SCHEMATIC DIAGRAMS ····················· 4-22
· DS-84 (TAPE OPERATION)
PRINTED WIRING BOARD ·················· 4-22
5.
INTERFACE, IC PIN FUNCTION
DESCRIPTION
5-1.
SYSTEM CONTROL ­
MECHANISM BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-1
5-2.
SYSTEM CONTROL ­
SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-341 BOARD IC160) ··············································· 5-1
5-3.
SYSTEM CONTROL ­
SYSTEM CONTROL PERIPHERAL
CIRCUIT INTERFACE (MA-341 BOARD IC160) ······· 5-2
5-4.
SYSTEM CONTROL AND RF MODULATOR ­
INPUT SELECTION BLOCK INTERFACE
(MA341 BOARD IC160) ················································ 5-2
5-5.
SYSTEM CONTROL ­ VIDEO/RP BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-2
5-6.
SYSTEM CONTROL ­ AUDIO BLOCK INTERFACE
(MA-341 BOARD IC160) ··············································· 5-2
5-7.
SERVO/SYSTEM CONTROL MICROPROCESSOR
PIN FUNCTIONS (MA-341 BOARD IC160) ················ 5-3
6.
ADJUSTMENTS
6-1
MECHANICAL ADJUSTMENTS ································· 6-1
6-2.
ELECTRICAL ADJUSTMENTS ··································· 6-1
1.
PREPARATION BEFORE ADJUSTMENT ··················· 6-1
1-1.
Equipment Required ························································ 6-1
1-2.
Equipment Connection ···················································· 6-1
1-3.
Set-up of Adjustment ······················································· 6-1
1-4.
Alignment Tape ······························································· 6-1
1-5.
Input/Output Levels and Impedance ······························· 6-2
1-6.
Adjustment Sequence ······················································ 6-2
2.
POWER SUPPLY CHECK ············································· 6-2
2-1.
Output Voltage Check (MA-341 Board) ························· 6-2
3.
SERVO SYSTEM CHECK ············································· 6-3
3-1.
RF Switching Position Adjustment (MA-341 Board) ····· 6-3
4.
AUDIO SYSTEM ADJUSTMENT ································· 6-3
4-1.
Hi-Fi Audio System Adjustment (Hi-Fi model only) ······ 6-3
4-2.
HiFi Switching Position Adjustment (MA-341 Board) ··· 6-4
4-3.
Normal Audio System Adjustment ·································· 6-4
4-3-1. ACE Head Adjustment ···················································· 6-4
4-3-2. E-E Output Level Check ················································· 6-4
4-3-3. Frequency Response Check ············································· 6-4
5.
ADJUSTING PARTS LOCATION DIAGRAM ············· 6-6
7.
REPAIR PARTS LIST
7-1.
EXPLODED VIEWS ······················································ 7-1
7-1-1. FRONT PANEL AND UPPER CASE SECTION ·········· 7-1
7-1-2. CHASSIS SECTION ······················································· 7-2
7-1-3. MECHANISM DECK SECTION-1 ······························· 7-3
7-1-4. MECHANISM DECK SECTION-2 ······························· 7-4
7-1-5. MECHANISM DECK SECTION-3 ······························· 7-5
7-2.
ELECTRICAL PARTS LIST ·········································· 7-6


background image
-- 4 --
1. ERROR CODE INDICATION
· Error codes are indicated using the lower 5 digits in the fluorescent display tube.
"At this time, Colon ":" between character is not indicated."
ERROR CODE
MODE CODE
0
Power-on eject
10 FWD x1
20 REW play
1
Power-on initial
11 FWD x2
21 Cas. loading
2
Power-off eject
12 CUE
22 Tape loading
3
Power-off stop
13 PB-pause
23 Power-off loading
4
FF
14 RVS-pause
24 Mecha. error (Power on)
5
REW
15 RVS x1
25 Power-on eject initial
6
REC
16 RVS x2
26 Power-off eject initial
7
REC- pause
17 REV
27 APC REC
8
Power-on stop
18 Power-off initial
28 Cas. loading
9
PB
19 Mecha. error (Power off)
(No auto PB check)
0
No error
1
Cam encoder error Loading direction
2
Cam encoder error Unloading direction
3
T reel error
4
S reel error
5
Capstan error
6
Drum error
7
Error on initializing
8
Cassette loading error
9
Reserve
SERVICE NOTE
Mode code indication when the error has occurred.
Error code


background image
1-1
SLV-662HF/672HF
SECTION 1
GENERAL
This section is extracted from
instruction manual.