background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2002
Model
Type
Power Requirement
Remarks
VSX-D711-K
MVXJI
AC230V
VSX-D711-K
MYXJIEW
AC220-230V
VSX-D711-K
MYXJIGR
AC220-230V
VSX-D711-S
MYXJIEW
AC220-230V
RRV2607
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D711-K
T ­ ZZV APR. 2002 Printed in Japan
VSX-D711-S
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
For details, refer to "Important symbols for good services" on page 3.
DOWN
UP
ENTER
INPUT
SELECTOR
MASTER VOLUME
MULTI JOG
R
STANDBY
STANDBY/ON
PHONES
Nm-Û,,
OFF
ON


background image
VSX-D711-K, VSX-D711-S
2
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 ­ Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse)
and/or
(slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide)
et/ou
(fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident
from visual
inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or
additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test


background image
VSX-D711-K, VSX-D711-S
3
[ Important symbols for good services ]
In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,
proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement parts
Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.


background image
VSX-D711-K, VSX-D711-S
4
SAFETY INFORMATION ................................................................... 2
1. SPECIFICATIONS ......................................................................... 5
2. EXPLODED VIEWS AND PARTS LIST ......................................... 6
2.1 PACKING ................................................................................ 6
2.2 EXTERIOR ............................................................................. 8
2.3 FRONT PANEL ..................................................................... 10
3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM .......................... 12
3.1 BLOCK DIAGRAM ................................................................ 12
3.2 OVERALL WIRING CONNECTION DIAGRAM ................... 14
3.3 DD & INPUT ASSY(1/4) ....................................................... 16
3.4 DD & INPUT ASSY(2/4) ....................................................... 18
3.5 DD & INPUT ASSY(3/4) ....................................................... 20
3.6 DD & INPUT ASSY(4/4) ....................................................... 22
3.7 AMP & PRIMARY(1/2), TRANS2 and TRANS3 ASSYS ............. 24
3.8 AMP & PRIMARY(2/2), REGULATOR, HASHIGETA
B TO B , AMP INPUT and TRANS 1 ASSYS ................ 26
3.9 DIGITAL IN ASSY ................................................................. 28
3.10 KAWA ASSY ....................................................................... 29
3.11 VIDEO and 6CH IN ASSYS ................................................ 30
3.12 S. VIDEO ASSY .................................................................. 31
3.13 FRONT, R. ENCODER and POWER SW ASSYS ............. 32
3.14 FRONT VIDEO and H.P. ASSYS ....................................... 34
3.15 TRANS4 and MECHA SW ASSYS ..................................... 35
3.16 FM/AM TUNER MODULE .................................................. 36
4. PCB CONNECTION DIAGRAM ................................................... 38
4.1 TRANS1, TRANS2, TRANS3 and TRANS4 ASSYS ............ 39
4.2 DD & INPUT ASSY ............................................................... 40
4.3 AMP & PRIMARY, AMP INPUT and MECHA SW ASSYS ......... 44
4.4 REGULATOR, HASHIGETA and KAWA ASSYS ................. 46
4.5 B TO B, DIGITAL IN, VIDEO and 6CH IN ASSYS ...................... 48
4.6 S. VIDEO and FRONT VIDEO ASSYS ....................................... 50
4.7 FRONT, POWER SW, H.P. and R. ENCODER ASSYS ............. 52
4.8 FM/AM TUNER MODULE ........................................................... 56
5. PCB PARTS LIST ........................................................................ 57
6. ADJUSTMENT ............................................................................. 63
7. GENERAL INFORMATION ......................................................... 64
7.1 DIAGNOSIS .......................................................................... 64
7.1.1 U-COM BLOCKDIAGRAM .................................................... 64
7.1.2 POWER ON AND OFF SEQUENCE .................................... 65
7.1.3 PROTECTION CIRCUIT ....................................................... 67
7.2.2 PCB LOCATION ................................................................... 68
7.2 PARTS .................................................................................. 69
7.2.1 IC ........................................................................................... 69
7.2.2 DISPLAY ............................................................................... 77
7.3 CLEANING ........................................................................... 78
8. PANEL FACILITIES ..................................................................... 79
CONTENTS


background image
5
VSX-D711-K, VSX-D711-S
Accessories
Remote control unit
(XXD3042)
AM loop antenna
(ATB7009)
FM wire antenna
(ADH7005)
AA size IEC R6P
Dry cell batteries (x2)
Miscellaneous
Power Requirements
UK model .......................................................... AC 230 V, 50/60 Hz
European model ......................................... AC 220-230 V, 50/60 Hz
Power Consumption
VSX-D711 .......................................................................... 250W
In Standby ............................................................................. 1 W
Dimensions ................................... 420 (W) x 158 (H) x 401 (D) mm
.........................................................10 kg
Furnished Parts
AM loop antenna ............................................................................ 1
FM wire antenna ............................................................................ 1
Dry cell batteries (AA size IEC R6P) .............................................. 2
Remote control ............................................................................... 1
Operating instructions .................................................................... 1
Specifications and the design are subject to possible modifications
without notice, due to improvements.
"DTS" ,"DTS-ES Extended Surround" and "Neo:6" are
trademarks of Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double D symbol are
trademarks of Dolby Laboratorories.
Amplifier Section
Continuous Power Output (STEREO mode)
Front ..................... 100 W per channel (DIN 1kHz, THD 1.0 %, 8
)
Continuous Power Output
Front ............................ 100 W per channel (1kHz, THD 1.0 %, 8
)
Center ............................................. 100 W (1kHz, THD 1.0 %, 8
)
Surround ..................... 100 W per channel (1kHz, THD 1.0 %, 8
)
· Above specifications are applicable when the power supply is
230V.
Input (Sensitivity/Impedance)
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT ... 200 mV/47 k
Frequency Response
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,
TV/SAT ...................................................... 5 Hz to 100,000 Hz
dB
Output (Level/Impedance)
VCR/DVR REC, CD-R/TAPE/MD REC .................... 200 mV/2.2 k
Tone Control
BASS ......................................................................
± 6 dB (100 Hz)
TREBLE ..................................................................
± 6 dB (10 kHz)
LOUDNESS .................................... +9 dB/+9 dB (100 Hz/10 kHz)
Signal-to-Noise Ratio [DIN (Continuous rated power output/50 mW)]
CD, VCR/DVR, CD-R/TAPE/MD,DVD/LD, TV/SAT .................. 96 dB
Video Section
Input (Sensitivity/Impedance)
VCR/DVR, DVD/LD, TV/SAT ......................................... 1 Vp-p/75
Output (Level/Impedance)
VCR/DVR ...................................................................... 1 Vp-p/75
Frequency Response
VCR/DVR, DVD/LD,TV/SAT
] MONITOR ........ 5 Hz to 7 MHz dB
Signal-to-Noise Ratio .............................................................. 55 dB
FM Tuner Section
Frequency Range .......................................... 87.5 MHz to 108 MHz
Usable Sensitivity ...................... Mono:13.2 dBf, IHF (1.3
µV/ 75 )
50 dB Quieting Sensitivity ......................................... Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio ................................ Mono: 73 dB (at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Signal-to-Noise Ratio (DIN) ......................................... Mono: 62 dB
Stereo: 58 dB
Distortion ........................................................ Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity ................................. 60 dB (400 kHz)
Stereo Separation ...................................................... 40 dB (1 kHz)
Frequency Response ................................. 30 Hz to 15 kHz (
±1 dB)
Antenna Input (DIN) .............................................. 75
unbalanced
AM Tuner Section
Frequency Range ........................................... 531 kHz to 1,602 kHz
Sensitivity (IHF, Loop antenna) ......................................... 350
µV/m
Selectivity ................................................................................ 25 dB
Signal-to-Noise Ratio .............................................................. 50 dB
Antenna ...................................................................... Loop antenna
+0
­ 3
+0
­ 3
Weight (without package)
1. SPECIFICATIONS