background image
PDP-S21-LR
PDP-S22-LR
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
Gebruiksaanwijzing
Manual de instrucciones
Speaker System
Enceintes acoustiques
Lautsprechersystem
Sistema di diffusori
Luidsprekersysteem
Sistema de altavoces


background image
English
2
CHECKING THE ACCESSORIES
7 Speaker cable x 2
Thank you for buying this Pioneer product.
Please read through these operating instructions before
using your speaker system so you will know how to make
the most of its performance. After you have finished reading
the instructions, put them away in a safe place for future
reference.
WARNING:
Handling the power cord on this product or cords
associated with accessories sold with the product will
expoes you to lesd, a chemical known to the State of
California and other governmental entities to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling.
BEFORE USE
÷ The nominal impedance of this speaker system is 8 ohms.
÷ In order to prevent damage to the speaker system
resulting from input overload, please observe the
following precautions:
÷ Do not supply power to the speaker system in
excess of the maximum permissable input. This
can result in damage or a possible fire hazard.
÷ When connecting or disconnecting pin-plugs, be
sure that amplifier power is OFF.
÷ When using a graphic equalizer to emphasize loud
sounds of a high frequency range, do not use
excessive amplifier volume.
÷ Do not force a low-powered amplifier to produce a
loud volume of sound (the amplifier's harmonic
distortion will be increased, and you may damage
the speaker).
÷ An automatic restore-type protective device is incorporated
to protect the speakers from excessive input signals or
abnormal signals. When an excessive input signal is sent
to the speakers, the protective device is activated and
loud high-pitched sounds will be prevented. In this case,
lower the volume of the plasma display during use. After
5 to 10 seconds, the speakers are restored automatically.
÷ Placing a CRT computer screen or CRT monitor near to
the speakers may result in interference or color distortion.
If this happens, distance the monitor from the speakers.
7 Operating Instructions
7 Speaker mounting fittings (Used when installing the
speakers on the right and left sides of the display)
Bracket for installing the
speakers on the right x 2
7 Speaker mounting fittings (Used when installing the
speakers at the bottom of the display)
7 Speakers mounting screws
NOTE:
÷ Always use the accessory mounting fittings for
installation.
÷ When screws other than those enclosed as accessories
are used to install the speakers, the speakers may drop
off or accidents may be caused. Always use the screws
enclosed as accessories.
Notes on Installation Work:
This product is marketed assuming that it is installed by
qualified personnel with enough skill and competence.
Always have an installation specialist or your dealer install
and set up the product.
PIONEER cannot assume liabilities for damage caused
by mistake in installation or mounting, misuse,
modification or a natural disaster.
x 12
The customer can select whether to install the speakers on
the right and left sides of the display or at the bottom of the
display.
When the speakers are installed
on the right and left sides
When the speakers are
installed at the bottom
See the description below for details of the installation.
CAUTION:
÷ Attach the plasma display to the stand (PDK-TS05) before
installing the speakers. See the Operating Instructions
packed together with the stand for how to assemble the
stand.
Bracket for installing the speakers at
the bottom x 2 for right and left sides
Bracket for installing the speakers
at the bottom x 1 for center
Rivet for installing the speakers at
the bottom x 2
Bracket for installing the
speakers on the left x 2


background image
3
English
English
INSTALLATION ON THE PLASMA
DISPLAY
(WHEN INSTALLING THE SPEAKERS ON THE RIGHT AND
LEFT SIDES OF THE DISPLAY)
1 Attach the mounting fittings to the
speakers.
The illustration below shows the right speaker. Attach the left
side mounting fitting in the same way.
1 Attach a bracket (R) to the top of the right speaker, as
shown.
2 Attach another bracket (R) to the bottom of the speaker
in the same way.
2 Attach the speakers to the display.
The illustration below shows how to attach of the right speaker.
Attach the left speaker in the same way.
1 Fix the upper screw temporarily in
advance to hang the speaker on
the display (In this case, leave a
space of about 5 mm between the
head of the screw and the display).
2 Hang the speaker on the upper
screw.
3 Fix the lower screw temporarily.
4 Adjust the position so that the speaker is parallel to the
display and then fix the upper and lower screws firmly.
Perform installation according to the following steps 1 to 2.
INSTALLATION ON THE PLASMA
DISPLAY
(WHEN INSTALLING THE SPEAKERS AT THE BOTTOM
OF THE DISPLAY)
1 Attach the mounting fittings to the
display.
1 Push rivets into each (lower) outside hole of brackets (on
the right and left sides).
2 Lightly finger-tighten a screw into the (upper) outside hole of
each bracket.
3 Insert the screws into the two outside holes of bracket
(at the center), and tighten them.
4 Attach the speaker cushions supplied with your plasma
display.
5 Align the bosses of the spacer with the holes of the stand
and insert them.
2
5mm
The display
1
24
3
Perform installation according to the following steps 1 to 2.
1
1
2
2
Separate the 3 cushions evenly, making
sure you don't cover the screws with the
speaker cushions when placing them.
Lower back side of the plasma
display speaker system


background image
English
4
2 Similarly, insert the other speaker into the bracket on the
left side.
3 Adjust so that the clearance between the speakers is lost
and so that the speakers are not shifted to the right or left.
4 Fix the two points in the center of the display with screws.
5 Fix the two points on the right and left sides with screws.
Adjust so that the speaker system is parallel to the dis-
play and then finish securing the screws you had lightly
tightened on the mounting fittings.
When the speakers are installed
on the right and left sides
When the speakers are
installed at the bottom
CONNECTION TO A PLASMA
DISPLAY
1 Connecting the speaker cables
1 Switch off the power of the plasma display.
2 Connect the input terminals of the speaker system and
the speaker output terminals of the plasma display with
the accessory speaker cable. Make sure the positive (
ª)
and negative (
·) terminals match when connecting.
1. Push the lever, insert the cable into the hole, and release the lever.
To the
· terminal
To the
ª terminal
(Speaker input terminals of the speaker system)
· terminal (black) ª terminal (red)
Input terminal of speaker
White
White with gray line
÷ Make sure not to push on the speaker cover with force,
using your fingers or otherwise. The speaker cover can
be broken, and damage to the speaker unit may also
occur as a result.
NOTE:
÷ When attaching the speakers to the plasma display,
make sure to tighten all the screws, making sure the
speakers are secure and do not shake.
÷ When the display is to be moved after speaker
installation, do not hold the display by the speakers. Hold
the handle of the display and the side or bottom of the
display with reference to the figures below when moving
the speaker system. Do not hold the speakers and raise
the display. This may cause the deformation or damage
of products.
Make sure the speaker
is fit snug against the
bracket, then tighten
the screws.
2 Attach the speakers to the display.
Take care to ensure that the display does not hit the
speakers in steps 1 and 2 when speakers are installed on
the display.
1 Place it below the display while inclining one speaker and
insert it into the bracket on the right side.


background image
5
English
English
2. For the output terminals on the plasma display, push the lever,
insert the cable into the hole, and release the lever.
÷ After connection to the terminals, pull lightly on the cable
to confirm that the tips of the cable are properly connected
to the terminals. An imperfect connection can cause
sound interruptions and noise.
÷ When cable cores stick out and ª and · lines are short-
circuited, an excessive load will be applied to the plasma
display and the operation will stop or trouble will be
caused.
2 How to route cables
Speed clamps are included with the plasma display for tidying your cables and keeping extra cable length out of the way.
When installing the speakers on the right and left sides of the display
Speed clamps
Speaker cable
Speaker cable
When installing the speakers at the bottom of the display
A speaker cable or system cable is put in
the rack using a supplied wiring clamp so
that it cannot be viewed from the front.
Speaker cable
Wiring clamp
Wiring clamp
ª ··ª
RL
Output terminal of plasma
display
Speaker cable
÷ When the polarity is reversed for one speaker (left or right)
at the time of connection to the plasma display, the bass
reproduction will be reduced, the sound positioning will
be lost, and a correct stereo effect will not be obtained.
÷ If you insert the speaker cord too far so that the insulation
is touching the speaker terminal, you may not get any
sound.
< right >
< wrong >