KENWOOD KAC-8103D - Owner's Manual Immediate Download

KAC-8103D

CLASS D MONO POWER AMPLIFIER

7 page 2-6

INSTRUCTION MANUAL

2 English

Safety precautions

2WARNING

To prevent injury or fire, take the following precautions:

· When extending the ignition, battery, or ground wires, make sure to use

automotive-grade wires or other wires with a 8 mm2 (AWG 8) or more to

prevent wire deterioration and damage to the wire coating.

· To prevent a short circuit, never put or leave any metallic objects (such as

coins or metal tools) inside the unit.

· If the unit starts to emit smoke or strange smells, turn off the power

immediately and consult your Kenwood dealer.

· Do not touch the unit during use because the surface of the unit becomes

hot and may cause burns if touched.

· Mounting and wiring this product requires skills and experience. For safety's

sake, leave the mounting and wiring work to professionals.

2CAUTION

To prevent damage to the machine, take the following

precautions:

· Be sure the unit is connected to a 12V DC power supply with a negative

ground connection.

· Do not open the top or bottom covers of the unit.

· Do not install the unit in a spot exposed to direct sunlight or excessive heat

or humidity. Also avoid places with too much dust or the possibility of water

splashing.

· When replacing a fuse, only use a new one with the prescribed rating. Using a

fuse with the wrong rating may cause your unit to malfunction.

· To prevent a short circuit when replacing a fuse, first disconnect the wiring

harness.

NOTE

· If you experience problems during installation, consult your Kenwood dealer.

· If the unit does not seem to be working right, consult your Kenwood dealer.

Cleaning the unit

If the front panel gets dirty, turn off the power and wipe the panel with a dry

silicon cloth or soft cloth.

2CAUTION

Do not wipe the panel with a hard cloth or a cloth dampened by volatile

solvents such as paint thinner and alcohol. They can scratch the surface of the

panel and/or cause the indicator letters to peel off.

To prevent battery rise

When the unit is used in the ACC ON position without turning the engine ON, it

depletes the battery. Use it after starting the engine.

Protection function

The protection function is activated in the following situations:

This unit is equipped with a protection function for protecting this unit and your

speakers from various accidents or problems that can occur.

When the protection function is triggered, the Power indicator goes OFF and

the amplifier stops operating.

· When a speaker wire may be short-circuited.

· When a speaker output contacts ground.

· When the unit malfunctions and a DC signal is sent to the speaker output.

· When the internal temperature is high and unit won't operate.

· When a ground wire of the center unit (cassette receiver, CD receiver, etc.)

or this unit is not connected to a metal part serving as an electrical ground

passing electricity to the battery's negative

- terminal.

Wiring

· Take the battery wire for this unit directly from the battery. If it's connected to

the vehicle's wiring harness, it can cause blown fuses etc.

· If a buzzing noise is heard from the speakers when the engine is running,

connect a line noise filter (optional) to each of the battery wire.

· Do not allow the wire to directly contact the edge of the iron plate by using

Grommets.

· Connect the ground wire to a metal part of the car chassis that acts as an

electrical ground passing electricity to the battery`s negative

- terminal. Do

not turn the power on if the ground wire is not connected.

· Be sure to install a protective fuse in the power cord near the battery. The

protective fuse should be the same capacity as the unit's fuse capacity or

somewhat larger.

· For the power cord and ground, use a vehicle type (fireproof ) power wring

cord with a current capacity greater than the unit's fuse capacity. (Use a power

wiring cord with a diameter of 8 mm2 (AWG 8) or greater.)

· When more than one power amplifier are going to be used, use a power

supply wiring wire and protective fuse of greater current-handling capacity

than the total maximum current drawn by each amplifier.

Speaker Selection

· The rated input power of the speakers that are going to be connected should

be greater than the maximum output power (in Watts) of the amplifier. Use of

speakers having input power ratings that are less than the output power of

the amplifier will cause smoke to be emitted as well as damage.

· Use speakers that have an impedance of 2 or greater. When more than one

set of speakers are going to be used, calculate the combined impedance of

the speakers and then connect suitable speakers to the amplifier.

Combined impedance

English

Installation

Accessories

Part name

External View

Number of Items

Self-tapping screws

(ø5 × 18 mm)

Terminal cover (Small)

(Power terminal)

Terminal cover (Large)

(Speaker terminal)

Speaker level input cable

Installation procedure

Since there are large variety of settings and connections possible according to

applications, read the instruction manual well to select the proper setting and

connection.

1.Remove the ignition key and disconnect the negative

- terminal of the

battery to prevent short circuits.

2.Set the unit according to the intended usage.

3.Connect the input and output wires of the units.

4.Connect the speaker wires.

5.Connect the power wire, power control wire and grounding wire following this

order.

6.Install the installation fittings in the unit.

7.Attach the unit.

8.Connect the negative

- terminal of the battery.

2CAUTION

· Do not install in the below locations;

(Unstable location, In a location that interferes with driving, In a location

that gets wet, In a dusty location, In a place that gets hot, In a place that

gets direct sunlight, In a location that gets hit by hot air)

· Do not install the unit under the carpet. Otherwise heat build-up occurs

and the unit may be damaged.

· Install this unit in a location which allows heat to easily dissipate.

Once installed, do not place any object on top of the unit.

· The surface temperature of the amplifier will become hot during use. Install

the amplifier in a place where people, resins, and other substances that are

sensitive to heat will not come into contact with it.

· When making a hole under a seat, inside the trunk, or somewhere else in

the vehicle, check that there is nothing hazardous on the opposite side

such as a gasoline tank, brake pipe, or wiring harness, and be careful not to

cause scratches or other damage.

· Do not install near the dashboard, rear tray, or air bag safety parts.

· The installation to the vehicle should securely fasten the unit to a place in

which it will not obstruct driving. If the unit comes off due to a shock and

hits a person or safety part, it may cause injury or an accident.

· After installing the unit, check to make sure that electrical equipment

such as the brake lamps, turn signal lamps and windshield wipers operate

normally.

Class D Mono

318 mm

258 mm

Ø6

272

286

Installation board, etc.

(thickness : 15 mm or more)

Self-tapping screw

(ø5 × 18 mm)

NOTE

· Do not remove the dressing cover.

4 English

2WARNING

To prevent fire caused by a short in the wiring,

connect a fusible link or breaker nearby the

battery's positive terminal.

2CAUTION

· If sound is not output normally, immediately

turn power off and check connections.

· Be sure to turn the power off before changing

the setting of any switch.

· If the fuse blows, check wires for shorts, then

replace the fuse with one of the same rating.

· Check that no unconnected wires or

connectors are touching the car body. Do

not remove caps from unconnected wires or

connectors to prevent short circuits.

· Connect the speaker wires to appropriate

speaker connectors separately. Sharing the

negative wire of the speaker or grounding

speaker wires to the metal body of the car can

cause this unit to fail.

· After installation, check that the brake lamps,

winkers, and wipers work properly.

NOTE

· Do not connect cables and leads to both RCA

cable input jacks and the speaker level input

terminals simultaneously, for this may cause

malfunction or damage.

* Commercially available parts

Connection

Lead terminal*

Battery

Ground wire*

Power control wire

Subwoofer (L + R)

Battery wire*

Protective Fuse*

Terminal cover

(Small)

CENTER UNIT

(CD receiver, etc.)

RCA cable*

Power control wire

Left input

Right input

RCA cable or Speaker level input connection

Power wire and Speaker wire connection

Genuine-accessory car

stereo (No line output

center unit etc.)

ACC

Battery

Car fuse box

· RCA cable connections

· Speaker level input connections

Cable Color of the connector

Left

9White

·White/Black

Right

9 Gray

· Gray/Black

Terminal cover

(Large)

English

Controls

1 Fuse (40 A × 1)

NOTE

If you can't find the specified capacity fuse at your store etc., consult your

Kenwood dealer.

2 Battery terminal

3 Ground terminal

4 Power control terminal

Controls the unit ON/OFF.

NOTE

Controls the unit power. Be sure to connect it with all the systems.

5 Speaker output terminals

As this unit accepts speakers with a minimum impedance of 2 ohms,

connect speakers with 2-ohms or higher impedance to these terminals.

2CAUTION

The rated input of the speakers should be no less than the maximum output

of the amplifier. Otherwise malfunction may result.

6 BASS BOOST LEVEL control

Sets the low frequency level to be compensated.

7 LPF(Low-Pass Filter) FREQUENCY control

This control adjusts the frequency band output from this unit.

8 ISF (infrasonic filter) switch

Ultralow frequencies that cannot be reproduced even by a subwoofer

speaker do not become sound but become unnecessary oscillations, which

affect the sound by causing distortion, etc. Setting this switch to "15 Hz" or

"25 Hz" cuts the frequencies below the respective frequency.

This improves the reproduction performance of the speakers by eliminating

unnecessary oscillations which will not become sound.

9 INPUT SENSITIVITY control

Set this control according to the pre-output level of the center unit

connected with this unit, or to the maximum power output of the genuine-

accessory car stereo.

Use the diagram on the right as a guide.

NOTE

For the pre-output level or the maximum power output, refer to the

<Specifications> in the instruction manual of the center unit.

0 Speaker level input terminals

NOTE

· The genuine-accessory car stereo shall have a maximum power output of

no more than 40 W.

· Do not connect the speaker output leads from a power amplifier (Optional)

to the speaker level input terminals of this unit, for this may cause

malfunction or damage.

· Do not connect cables and leads to both RCA cable input jacks and

the speaker level input terminals simultaneously, for this may cause

malfunction or damage.

· Connect the power control lead to a power supply which can be turned

ON/OFF by the ignition key switch (ACC line). With this connection, shock

noise may be generated when the power of the genuine-accessory car

stereo is switched ON/OFF.

! LINE IN terminal

@ LINE OUT terminal

The signal that's input from the line input terminal is output.

# Power indicator

When the power is turned on, the Power indicator lights.

If the Power indicator does not light when the power is turned on, the

protection function may be activated. Check whether there is any indication

of trouble. (See page 2)

15W 40W

Class D Mono