background image
Module No. 2174
2174-1
GENERAL GUIDE
· Press B to change from mode to mode.
· Pressing L in any mode illuminates the display for about 3 seconds.
· If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
· If you do not perform any operation for a few minutes in the Day Counter Mode or Telememo Mode, the watch automatically reverts to the normal timekeeping screen.
· When making settings, note that you can scroll only forward, you cannot scroll back. This means that if you go past the setting you want, you must scroll through all of the available
settings again until the one you want reappears.
Timekeeping Mode
World Time Mode
Day Counter Mode
Telememo Mode
Stopwatch Mode
Press
B.
Alarm Mode
TIMEKEEPING MODE
· Press C to toggle the display between the day of the week and month, as shown
below.
Press C.
Hour
Minutes
City code
Seconds
DST on
indicator
Day
Month
Day of week
· Hold down C to toggle between 12-hour and 24-hour timekeeping. Note that press-
ing C also switches the display between the day of the week and month screens
as described above.
· With 12-hour timekeeping, times between midnight and noon are indicated by A
(am), while times between noon and midnight are indicated by P (pm).
· The A and P indicators do not appear when you are using 24-hour timekeeping.
To set the time and date
1. While in the Timekeeping Mode, hold down A until the seconds digits flash on the
display, indicating the setting screen.
2. Press B to move the flashing in the sequence shown below.
DST
Seconds
Month
Day
City code
Minutes
Year
Hour
3. While the seconds setting is selected (flashing), press C to reset it to 00. If you
press C while the seconds setting is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range of
00 to 29, the minutes count is unchanged.
· While the DST setting is selected (DST on indicator is flashing), press C to toggle
it on (ON) and off (OF).
· The DST on/off setting you make for the Timekeeping Mode does not affect the
World Time Mode.
· While the city codes setting is selected, use C to scroll thorough the available
codes until the one you want to use as your home time city is displayed.
· For full information on city codes, see the "CITY CODE TABLE".
4. While any other setting is selected (flashing), press C to increase it. Holding down
C changes the setting at high speed.
5. After you make the settings you want, press A to exit the setting screen.
· The day of the week is automatically set in accordance with the date.
· The date can be set within the range of January 1, 2000 to December 31, 2039.
· The watch's built-in full automatic calendar automatically makes allowances for dif-
ferent month lengths and leap years. Once you set the date, there should be no
reason to change it except after the replacement of the watch's battery.
Daylight Saving Time (DST), which is also sometimes called "summer time" ad-
vances the time for one hour, as is the custom in some areas during the summer.
Remember that not all countries or even local areas use Daylight Saving Time.
ABOUT THE BACKLIGHT
· Press L to illuminate the display for about three seconds.
· The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
· Frequent use of the backlight shortens the battery life.
· The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.
· The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
· The backlight automatically turns off whenever an alarm sounds.
WORLD TIME MODE
Hour : Minutes
Seconds
DST on indicator
Day
Day of week
Mode indicator
City code
Month
[Month-day display]
The World Time Mode shows the current time in 40 cities (27 time zones) around the
world. The lower part of the display shows either the day of the week and day, or the
month and day. The format used is the one you select in the Timekeeping Mode
before entering the World Time Mode.
· For full information on city codes, see the "CITY CODE TABLE".
· The time setting of the Timekeeping Mode and the World Time Mode are synchro-
nized, except for the daylight saving time (summer time) setting. Whenever you
change the time setting for any city in the Timekeeping Mode, the settings of all
World Time cities are changed accordingly.
· The World Time Mode has its own daylight saving time (summer time) setting.
To select a World Time City and view its time
In the World Time Mode, press C to scroll forward through the city codes (time
zones). Holding down C scrolls at high speed.
· You can set up an alarm in the Alarm Mode so it operates based on the current time
in a city you specify in the World Time Mode.
Daylight Saving Time (DST)
Daylight Saving Time automatically advances the time setting by one hour from Stan-
dard Time. You cannot make individual Daylight Saving Time settings for each city
code (time zone). Turning on Daylight Saving Time affects all World Time time zones.
Remember that not all countries or even local areas use Daylight Saving Time.
To switch between Standard Time and Daylight Saving Time
In the World Time Mode, hold down A toggle between Daylight Saving Time and
Standard Time.
Hold down A.
DST on indicator
DST OFF
DST ON
DAY COUNTER MODE
The Day Counter Mode lets you count the number of days from the Timekeeping
Mode's current date to a specific target date.
This watch has five day counters. You can assign text titles up to eight characters
long to each of the five Day Counters. Whenever the date specified by any one of the
day counters matches the date of the Timekeeping Mode (regardless of the day
counter's year setting), the DAYS indicator flashes on the Timekeeping Mode. In the
Day Counter Mode, the DAYS indicator flashes on the screen of the particular day
counter whose date matches the date of the Timekeeping Mode.
The initial default date for all Day Counters is January 1, 2001.
Year
Month - Day
Target date
Numbers of days
Text
DAYS indicator
Mode
indicator
Alternate at the
1-second interval.
· The day counter on the display when you exit the Day Counter Mode appears first
the next time you enter the Day Counter Mode.
Recalling Day Counter Data
In the Day Counter Mode, press C to scroll through the day counters.


background image
2174-2
To set the target date
1. In the Day Counter Mode, press C to display the day counter you want to set.
2. Hold down A until the flashing cursor appears in the text area. This indicates the
input screen.
3. Press B to move the flashing in the sequence shown below.
Press B.
1st digit
Day
8th digit
Year
Month
4. While the cursor is in the text area, use C to scroll through characters at the
current cursor position. Characters scroll in the sequence shown below. Holding
down C scrolls at high speed.
Press C.
(Space)
A to Z
0 to 9
. (Period)
- (Hyphen)
5. While the cursor is in the date area, press C to scroll through digits at the current
cursor position. Holding down C scrolls at high speed.
· Press C and L at the same time, and the message "CLR" appears in the display.
The characters in the text area is cleared and today's date is set as the target date.
You can then make any changes in the date you want.
6. After you make the settings you want, press A to exit the input screen.
· The date can be set within the range of January 1, 1940 to December 31, 2039.
· The text area display can show only three characters at a time. Longer text scrolls
continuously from right to left. The symbol " " indicates that the character to the left
is the last, and the character to the right is first.
TELEMEMO MODE
The Telememo Mode lets you store up to 20 records, each
with a name (up to eight characters) and a phone number
(up to 12 digits). You can recall records by scrolling through
them on the display.
· The page number on the display when you exit the Tele-
memo Mode appears first the next time you enter the
Telememo Mode.
To input a new Telememo record
1. In the Telememo Mode, press C to display the page
number of the record where you want to input data.
2. Hold down A and a cursor appears on the text area.
3. Use C to scroll through characters at the current cursor position. Characters scroll
in the sequence shown below.
Press C.
(Space)
A to Z
0 to 9
. (Period)
- (Hyphen)
· Holding down C scrolls at high speed.
4. When the character you want is at the current cursor position, press B to move
the cursor to the right.
Press B.
1st digit
8th digit
12th digit
1st digit
Text area
Number area
5. Repeat the steps 3 and 4 to input the rest of the characters.
· You can input up to eight characters for the name, though only three characters are
visible at a time. If the name you input has fewer than eight characters, use B to
move the cursor to the eighth space (which means you would press B three times
after inputting a five-character name).
6. After you input the name, use B to move the cursor to the number area.
· Pressing B while the cursor is located at the eighth character of the text area
advances to the number area. Pressing B while the cursor is located at the 12th
digit of the number area returns to the text area.
7. Use C to scroll through characters (hyphen, numbers, space) at the current cur-
sor position on the number area. Characters scroll in the sequence shown below.
Press C.
(Space)
0 to 9
- (Hyphen)
· Holding down C scrolls characters at high speed.
8. When the character you want is at the cursor position, press B to move the cursor
to the right.
9. Repeat steps 7 and 8 to input the rest of the numbers you want.
· You can input up to 12 digits for the number.
10. After inputting the name and number of the record, press A to store it and exit
the setting screen.
· The display can show only three name characters at a time. Longer names scrolls
continuously from right to left. The symbol " " indicates that the character to the left
is the last, and the character to the right is the first.
· The number area can show up to six digits at one time. If a number has more than
six digits, the display automatically switched between the first six digits (counting
forward from the first digit) and the last six digits (counting backward from the last
digit) of the number. This means that if a number is 12 digits long, the number area
switches between the first six digits and the last six digits. If a number is seven
digits long, the number area switches between digits 1 through 6, and 2 through 7.
To recall Telememo data
In the Telememo Mode, press C to scroll forward through the stored records.
· Holding down C scrolls at high speed.
To edit Telememo data items
1. In the Telememo Mode, use C to display the data you want to edit.
2. Hold down A until the cursor appears in the display.
3. Use B to move the cursor to the character you want to change.
4. Use C to change the character.
· See step 3 of "To input a new Telememo record" for information on inputting name
characters, and step 7 for inputting number characters.
5. After making the changes that you want, press A to store them and exit the set-
ting screen.
Mode indicator
Page number
Text area
Number area
To delete a Telememo record
1. In the Telememo Mode, use C to display the record you want to delete.
2. Hold down A until the cursor appears in the display.
3. Press C and L at the same time. The message "CLR" appears in the display,
indicating that the record was deleted.
· After the record is deleted, the cursor appears in the text area, ready for input.
4. Input a new record or press A to exit the setting screen.
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes, 59.99 seconds.
Changing to another mode while a split time is on the dis-
play clears the split time.
Elapsed time measurement
Start
Stop
Re-start
Stop
Clear
Start
Split
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split time measurement
Split time and 1st-2nd place times
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. Press any button
to stop the alarm after it starts to sound. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
· You can also specify a time zone for the Daily Alarm.
The alarm sounds when the alarm time matches the
current time in the time zone you specify.
· The Hourly Time Signal also sounds in accordance with
the time zone you specify.
· If the DST on indicator is on the display in the Alarm
Mode, it means that Daylight Saving Time (summer time)
is turned on for the time zone whose alarm you are set-
ting.
To set the alarm time
1. While in the Alarm Mode, hold down A until the city code flash on the display,
indicating the setting screen.
· At this time, the alarm is turned on automatically.
2. Press B to move the flashing in the sequence shown below.
Time zone
Minutes
Hour
3. While the time zone is flashing, press C to toggle between the city codes which
you selected in the Timekeeping Mode and the one you selected in the World Time
Mode.
4. While the hour or minutes digits of the alarm time are flashing, press C to in-
crease them. Holding down C changes the setting at high speed.
5. After you make the settings you want, press A to exit the setting screen.
· The format (12-hour and 24-hour) of the alarm time matches the format you select
in the Timekeeping Mode.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
· Changing the Home Time zone or the World Time city after setting an alarm causes
the alarm time to change as well.
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm or the Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Hourly Time
Signal only
Daily Alarm
only
Both OFF
Both ON
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
· Holding down C to test the alarm also changes the Daily Alarm and Hourly Time
Signal on/off settings.
Mode indicator
Hours : Minutes
1/100 second
Seconds
Mode indicator
Hour : Minutes
Alarm on indicator
Hourly time signal on
indicator
Time zone


background image
2174-3
CITY CODE TABLE
­11
PPG
PPG
PPG
PPG
PPG PAGO PAGO
--
­10
HLN
HLN
HLN
HLN
HLN
HONOLULU
PAPEETE
­9
ANC
ANC
ANC
ANC
ANC ANCHORAGE
NOME
­8
YVR
YVR
YVR
YVR
YVR VANCOUVER
LAS VEGAS, SEATTLE, DAWSON CITY
SFO
SFO
SFO
SFO
SFO SAN FRANCISCO
LAX
LAX
LAX
LAX
LAX LOS ANGELES
­7
DEN
DEN
DEN
DEN
DEN
DENVER
EL PASO, EDMONTON
­6
MEX
MEX
MEX
MEX
MEX MEXICO CITY
HOUSTON, DALLAS/FORT WORTH,
CHI
CHI
CHI
CHI
CHI
CHICAGO
NEW ORLEANS, WINNIPEG
­5
MIA
MIA
MIA
MIA
MIA
MIAMI
MONTREAL, DETROIT, BOSTON,
NYC
NYC
NYC
NYC
NYC
NEW YORK
PANAMA CITY, HAVANA, LIMA, BOGOTA
­4
CCS
CCS
CCS
CCS
CCS
CARACAS
LA PAZ, SANTIAGO, PORT OF SPAIN
­3
RIO
RIO
RIO
RIO
RIO RIO DE JANEIRO
SAO PAULO, BUENOS AIRES, BRASILIA,
MONTEVIDEO
+0
LON
LON
LON
LON
LON
LONDON
DUBLIN, LISBON, CASABLANCA, DAKAR,
ABIDJAN
+1
PAR
PAR
PAR
PAR
PAR
PARIS
MADRID, FRANKFURT, AMSTERDAM,
MIL
MIL
MIL
MIL
MIL
MILAN
VIENNA ALGIERS, STOCKHOLM, HAMBURG
ROM
ROM
ROM
ROM
ROM
ROME
BER
BER
BER
BER
BER
BERLIN
+2
IST
IST
IST
IST
IST
ISTANBUL
ATHENS, HELSINKI, BEIRUT, DAMASCUS,
CAI
CAI
CAI
CAI
CAI
CAIRO
CAPE TOWN
JRS
JRS
JRS
JRS
JRS JERUSALEM
+3
JED
JED
JED
JED
JED
JEDDAH
MOSCOW, KUWAIT, RIYADH, ADEN,
ADDIS ABABA, NAIROBI
+3.5
THR
THR
THR
THR
THR
TEHRAN
SHIRAZ
+4
DXB
DXB
DXB
DXB
DXB
DUBAI
ABU DHABI, MUSCAT
+4.5
KBL
KBL
KBL
KBL
KBL
KABUL
--
+5
KHI
KHI
KHI
KHI
KHI
KARACHI
--
MLE
MLE
MLE
MLE
MLE
MALE
+5.5
DEL
DEL
DEL
DEL
DEL
DELHI
MUMBAI, CALCUTTA
+6
DAC
DAC
DAC
DAC
DAC
DHAKA
COLOMBO
+6.5
RGN
RGN
RGN
RGN
RGN
YANGON
--
+7
BKK
BKK
BKK
BKK
BKK
BANGKOK
JAKARTA, PHNOM PENH, HANOI,
VIENTIANE
+8
SIN
SIN
SIN
SIN
SIN SINGAPORE
KUALA LUMPUR, TAIPEI, PERTHBEIJING,
HKG
HKG
HKG
HKG
HKG HONG KONG
MANILA, ULAANBAATAR
+9
SEL
SEL
SEL
SEL
SEL
SEOUL
PYONGYANG
TYO
TYO
TYO
TYO
TYO
TOKYO
+9.5
ADL
ADL
ADL
ADL
ADL
ADELAIDE
DARWIN
+10
GUM
GUM
GUM
GUM
GUM
GUAM
MELBOURNE, RABAUL
SYD
SYD
SYD
SYD
SYD
SYDNEY
+11
NOU
NOU
NOU
NOU
NOU
NOUMEA
PORT VILA
+12
WLG
WLG
WLG
WLG
WLG WELLINGTON
CHRISTCHURCH, NADI, NAURU ISLAND
GMT
City
City
Other major cities in the same time zone
differential Code
*Based on data as of December 1999.