background image
Order No. MD0004066C2
AV Control Stereo Receiver
SA-EX140
Color
(K) ... Black Type
E ... Europe
EB ... Great Britain
EG ... Germany and Italy
SPECIFICATIONS
FM Tuner Section
Frequency Range
87.50-108.00 MHz
Sensitivity
S/N 30 dB
1.5
V/75
S/N 26 dB
1.3
V/75
S/N 20 dB
1.2
V/75
IHF usable sensitivity
1.5
V/75
(IHF '58)
IHF 46 dB stereo quieting sensitivity
22
V/75
Total harmonic distortion
MONO
0.2%
STEREO
0.3%
S/N
MONO
60 dB (73 dB, IHF)
STEREO
58 dB (67 dB, IHF)
Frequency response 20 Hz-15 kHz
+1 dB, -2 dB
Alternate channel selectivity ±400 kHz
65 dB
Capture ratio
1.5 dB
Image rejection at 98 MHz
40 dB
IF rejection at 98 MHz
70 dB
Spurious response rejection at 98
MHz
70 dB
AM suppression
50 dB
Stereo separation
1


background image
1 kHz
40 dB
Carrier leak
19 kHz
-30 dB (-35 dB, IHF)
38 kHz
-50 dB (-55 dB, IHF)
Channel balance (250 Hz-6.3 kHz)
±1.5 dB
Limiting point
1.2
V
Bandwidth
IF amplifier
180 kHz
FM demodulator
1000 kHz
Antenna terminal
75
(unbalanced)
AM Tuner Section
Frequency Range
522-1611 kHz
Sensitivity
20
V, 330
V/m
Selectivity (at 999 kHz)
55 dB
IF rejection (at 999 kHz)
50 dB
Amplifier Section
Power output
DIN 1 kHz (T.H.D. 1%)
2 x 100 W (4
)
40 Hz-20 kHz continuous power
output both channels driven
2 x 80 W (8
)
Total harmonic distortion
rated power at 40 Hz-20 kHz
0.5% (8
)
half power at 1 kHz
0.07% (8
)
Power bandwidth
both channels driven. -3 dB
10 Hz-40 kHz (8
)
Damping factor
30 (8
)
Load impedance
Front
4-16
Frequency response
PHONO
RIAA standard curve (30 Hz-
15 kHz) ±0.8 dB
CD, TAPE, VCR
10 Hz-40 kHz, ±3 dB
Input sensitivity and impedance
PHONO
3 mV/47 k
CD, TAPE, VCR
200 mV/22 k
S/N at rated power (8
)
PHONO
70 dB (IHF, A: 80 dB)
CD, TAPE, VCR
75 dB (IHF, A: 85 dB)
Tone controls
BASS
50 Hz, +10 to -10 dB
TREBLE
20 kHz, +10 to -10 dB
Output voltage
TAPE REC (OUT), VCR OUT
200 mV
Channel balance (250 Hz-6.3 kHz)
±1 dB
Channel separation
55 dB
Headphones output level and
impedance
430 mV/330
2


background image
General
Power supply
AC 230-240 V, 50 Hz (For
EB only)
AC 230 V, 50 Hz (For E/EG only)
Power consumption
190 W
(in standby condition: 3 W)
Dimensions (W x H x D)
430 x 136 x 312 mm
Weight
7.0 kg
Notes:
1. Specifications are subject to change without notice. / Weight and
dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum analyzer.
2000 Matsushita Electronics (S) Pte. Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
1. Before Repair and Adjustment
Disconnect AC power, discharge Power Supply Capacitors C753 through a 10
, 5 W resistor
to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screw driver blade, for instance), as this
may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid over current.
Current consumption at AC 230 V, 50 Hz in NO SIGNAL mode should be 130~190 mA. (E/EG)
Current consumption at AC 230 - 240 V, 50 Hz in NO SIGNAL mode should be 130~190 mA. (EB)
2. Protection Circuitry
The protection circuitry may have operated if either of the following conditions are noticed:
- No sound is heard when the power is turned on.
- Stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and
negative speaker connection wires are "shorted", or if speaker systems with an impedance less
than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned
off and then on again.
3


background image
3. Accessories
AC power supply cord (E/EG)... 1 pc.
AC power supply cord (EB)... 1 pc.
AM Loop Antenna Set / ... 1 set.
FM Indoor Antenna... 1 pc.
Remote Control Transmitter... 1 pc.
4


background image
4. Caution for AC Mains Lead
5