background image
1)
Depending on the sound
field settings and the source,
sound will not be output.
Dynamic power output
155 W + 155 W, 8 ohms
220 W + 220 W, 4 ohms
(STR-DA80ES: US, Canadian)
Harmonic distortion at rated output
STR-DA80ES:
Less than 0.05 % (with
DIRECT PASS on)
TA-V88ES/TA-VA80ES:
Less than 0.7 % (with
DIRECT PASS on)
Frequency response
PHONO:
RIAA equalization curve
±0.5 dB
CD, TAPE, DAT/MD,
VIDEO 1, 2, 3, LD/DVD,
TV (/DBS):
10 Hz-50 kHz
dB (with
DIRECT PASS on)
+0.5
­2
MICROFILM
US Model
Canadian Model
STR-DA80ES
AEP Model
UK Model
TA-VA80ES
E Model
STR-DA80ES/TA-VA80ES
Australian Model
PX Model
STR-DA80ES
Chinese Model
TA-V88ES
SPECIFICATIONS
SERVICE MANUAL
STR-DA80ES/TA-V88ES/TA-VA80ES
Manufactured under license from Dolby
Laboratories Licensing Corporation.
"Dolby," the double-D symbol
a,
"AC-3" and "Pro Logic" are trademarks
of Dolby Laboratories Licensing
Corporation.
Photo: STR-DA80ES
STR-DA80ES
FM STEREO/FM-AM RECEIVER
TA-V88ES/TA-VA80ES
INTEGRATED AV AMPLIFIER
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 8-ohm load, both channels driven, from
20-20,000 Hz, rated 100 watts per channel,
minimum RMS power, with no more than
0.09 % total harmonic distorition from 250
milliwatts to rated output (US model).
Amplifier section
POWER OUTPUT
Stereo mode
STR-DA80ES:
(8 ohms 20 Hz-20 kHz,
THD 0.05 %)
100 W + 100 W
TA-V88ES:
(6 ohms at 1 kHz, THD 0.7%)
100 W + 100 W
TA-VA80ES:
(4 ohms at 1 kHz, THD 0.7%)
100 W + 100 W
Surround mode
STR-DA80ES:
(8 ohms at 1 kHz,
THD 0.05 %)
Front
: 100 W + 100 W
Center1)
: 100 W
Rear1)
: 100 W + 100 W
TA-V88ES:
(6 ohms at 1 kHz, THD 0.7%)
Front
: 100 W + 100 W
Center1)
: 100 W
Rear1)
: 100 W + 100 W
TA-VA80ES:
(4 ohms at 1 kHz, THD 0.7%)
Front
: 100 W + 100 W
Center1)
: 100 W
Rear1)
: 100 W + 100 W
Inputs
S/N
Sensitivity Impedance (weighting
network,
input level)
PHONO
2.5 mV
50
75 dB
kilohms
(A, 2.5 mV)
200 mV
CD
(STR-DA80ES)
150 mV
(TA-V88ES/VA80ES)
TAPE, DAT/
200 mV
50
82 dB
MD, VIDEO (STR-DA80ES) kilohms
(A, 150 mV)
1, 2, 3
150 mV
LD, TV/DBS (TA-V88ES/VA80ES)
TUNER
150 mV
(TA-V88ES/VA80ES)
LD DVD
--
75
100 dB
AC-3 RF IN
(A, 20 kHz, LPF)
LD DVD
COAXIAL
0.5 Vp-p
75
100 dB
IN
(A, 20 kHz, LPF)
LD DVD/TV
(DBS)/CD/
----
100 dB
DAT MD
(A, 20 kHz, LPF)
OPTICAL IN


background image
­ 2 ­
+0.5
­2
Outputs
REC OUT: DAT/MD, TAPE
Voltage: 200 mV
(STR-DA80ES)
150 mV
(TA-V88ES/VA80ES)
Impedance: 1 kilohm
AUDIO OUT: VIDEO 1, 2
Voltage: 200 mV
(STR-DA80ES)
150 mV
(TA-V88ES/VA80ES)
Inpedance: 1 kilohm
PRE OUT:
Voltage: 2 Vrms
Impedance: 1 kilohm
PHONES:
Accepts low and high
impedance headphones
BASS BOOST
+6 dB at 70 Hz
(STR-DA80ES)
+10 dB at 70 Hz
(TA-V88ES/VA80ES)
Digital signal processor section
Modulation (A/D conversion)
High Density Linear
Converter
Demodulation (D/A conversion)
High Density Linear
Converter (Advanced
pulse D/A converter)
Sampling frequency
48 kHz
Surround
LFE MIX:
MUTE, ­20 - 0 dB, 0.5 dB
step
D.RANGE COMP:
OFF, 0.1 - 0.9, STD, MAX
REAR level:
­20 - +10 dB, 0.5 dB step
CENTER level:
­20 - +10 dB, 0.5 dB step
SUB WOOFER level:
­20 - +10 dB, 0.5 dB step
EFFECT:
21-step adjustable
WALL:
17-step adjustable
SEAT
F/R: 17-step adjustable
L/R: 17-step adjustable
REBERB time:
17-step adjustable
Equalizer
BAND: BASS/TREBLE
Turnover frequency:
Bass: 99 Hz-992 Hz
Treble: 1.0 kHz-8.6 kHz
Level: ±10 dB, 0.5 dB step
FM tuner section (STR-DA80ES)
Tuning range 87.5-108.0 MHz
Antenna terminals
75 ohms, unbalanced
Sensitivity
Mono: 18.3 dBf, 4.5 µV
Stereo: 38.3 dBf, 45 µV
Usable sensitivity
11.2 dBf, 2 µV (IHF)
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3 %
Stereo: 0.5 %
Separation
45 dB at 1 kHz
Frequency response
30 Hz-15 kHz
dB
Selectivity
60 dB at 400 kHz
AM tuner section (STR-DA80ES)
Tuning range With 10 kHz interval:
530-1710 kHz (US and
Canadian models3))
530-1610 kHz (models for
all other countries except
for Australia)
With 9 kHz interval:
531-1710 kHz (US and
Canadian models)
531-1602 kHz (Australian
model and models for all
other countries3))
Antenna
Loop antenna
Usable sensitivity
50 dB/m (at 1,000 kHz or
999 kHz)
S/N
54 dB (at 50 mV/m)
Harmonic distortion
0.5 % (50 mV/m,
400 kHz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 db
3)
You can change the AM tuning interval to 9
kHz (US and Canadian models) or to 10 kHz
(models for all other countries except for
Australia). After tuning in any AM station,
turn off the receiver. Hold down the PRE-
SET TUNING + button and press the
POWER button. All preset stations will be
erased when you change the interval. To re-
set the interval to 10 kHz (or 9 kHz), repeat
the procedure.
Video section
Inputs
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-; 75 ohms
C: 0.286 Vp-p 75 ohms
Outputs
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
General
System
Tuner section:
PLL quartz-locked digital
synthesizer system
(STR-DA80ES)
Preamplifier section:
Low-noise NF type
equalizer
Power amplifier section:
Pure-complementary
parallel P.P.
Power requirements
US and Canadian models:
120 V AC, 60 Hz
Australian model:
240 V AC, 50 Hz
European models:
230 V AC, 50 Hz
Other models:
120/220/240 V AC
selectable, 50/60 Hz
Power consumption
STR-DA80ES:
US model: 340 W
Canadian model: 500 VA
Australian model: 380 W
Other models: 380 W
TA-V88ES: 370 W
TA-VA80ES: 380 W
AC outlets
STR-DA80ES:
US and Canadian models:
2 switched, total
120 W
Australian model:
1 switched, maximum
100 W
Other models:
2 switched, total
100 W
TA-V88ES/VA80ES:
1 switched, maximum 100 W
Dimensions 430
× 160 × 435 (4404)) mm
(17
× 63/8 × 17 1/4 (17 3/8)
inches) including
projecting parts and
controls
4) When the front cover is open
Mass (Approx.) 15.9 kg (35 Ib 1 oz)
(STR-DA80ES)
15.6 kg
(TA-V88ES/VA80ES)
Supplied accessories
FM wire antenna (1) (STR-DA80ES)
AM loop antenna (1) (STR-DA80ES)
Remote commander RM-P501 (remote) (1)
Size AA (R6) batteries (2)
Design and specifications are sbuject to
change without notice.


background image
­ 3 ­
TABLE OF CONTENTS
1.
GENERAL ................................................................... 4
2.
DISASSEMBLY .......................................................... 7
3.
ELECTRICAL ADJUSTMENTS ......................... 9
4.
DIAGRAMS
4-1.
IC Pin Function Description ............................................ 10
4-2.
Schematic Diagram ­ DISPLAY Section ­ .................... 24
4-3.
Printed Wiring Boards ­ DISPLAY Section ­ ................ 29
4-4.
Schematic Diagram ­ VIDEO Section ­ ......................... 33
4-5.
Printed Wiring Boards ­ VIDEO Section ­ .................... 37
4-6.
Schematic Diagram
­ INPUT/TUNER/POWER Section ­ ............................. 41
4-7.
Printed Wiring Boards
­ INPUT/TUNER/POWER Section ­ ............................. 45
4-8.
Schematic Diagram ­ DIGITAL Section ­ ...................... 50
4-9.
Printed Wiring Boards ­ DIGITAL Section ­ ................ 55
4-10. Schematic Diagram ­ AMP/OUTPUT Section ­ ............ 59
4-11. Printed Wiring Boards ­ AMP/OUTPUT Section ­ ....... 63
5.
EXPLODED VIEWS ................................................ 69
6.
ELECTRICAL PARTS LIST ................................ 74
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE
WITH MARK
! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL
OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
! SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES
SONT
CRITIQUES
POUR
LA
SÉCURITÉ
DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
MODEL IDENTIFICATION
­ BACK PANEL ­
STR-DA80ES US Model
: 373-3
STR-DA80ES Canadian Model : 373-4
STR-DA80ES Australian Model : 373-5
STR-DA80ES E, PX Model
: 373-6
TA-V88ES
Chinese Model
: 374-4
TA-VA80ES
AEP, UK, German,
EE, CIS Model
: 374-0
TA-VA80ES
E, Malaysia,
Singapore Model : 374-3
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15
µF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
4-991-


background image
­
4
­
This
section
is
e
xtr
acted
from
instr
uction
man
ual.
SECTION
1
GENERAL
·STR-D
A80ES
Front Panel Description


background image
­
5
­
·T
A-V88ES
Front Panel Description