background image
SERVICE MANUAL
MICRO SATELLITE SYSTEM
US Model
Canadian Model
E Model
Australian Model
Chinese Model
SA-VE325/WMS325
SS-CN325/V325
AEP Model
UK Model
SA-VE322/VE325/WMS325
SS-CN325/V325
Ver 1.2 2002.07
9-929-572-13
Sony Corporation
2002G0500-1
Home Audio Company
C
2002.07
Published by Sony Engineering Corporation
SPECIFICATIONS
SA-VE322/VE325/WMS325/
SS-CN325/V325
· SA-VE322/VE325 consists of the following models respectively.
SA-VE322
SA-VE325
Active Subwoofer (SA-WMS325)
aa
Center Speaker (SS-CN325)
­
a
Front and Rear Speakers (SS-V325)
aa
SA-WMS325
SS-V325
SS-CN325
SS-V325 (front and rear speakers)
Speaker system
Full range,
magnetically shielded
Speaker units
5.5
× 11 cm (7/
32 ×
7/
16
in.), cone type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
100 watts
Sensitivity level
87 dB (1 W, 1 m)
Frequency range
90 Hz - 20,000 Hz
Dimensions (w/h/d)
Approx. 70
× 152 × 126
mm (2 7/
8 × 6 × 5 in.),
including front grille
Mass
Approx. 830 g (18 lb 5
oz) each
SS-CN325 (center speaker)
Speaker system
Full range
× 2,
magnetically shielded
Speaker units
5.5
× 11 cm (7/
32 ×
7/
16
in.), cone type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
120 watts
Sensitivity level
89 dB (1 W, 1 m)
Frequency range
90 Hz - 20,000 Hz
Dimensions (w/h/d)
Approx. 300
78
126 mm (11 7/
8 × 3
1
/
8 ×
5 in.), including front
grille
Mass
Approx. 1600 g (35 lb 4
oz)
SA-WMS325 (subwoofer)
Speaker system
Active subwoofer,
magnetically shielded
Speaker unit
Woofer: 16 cm (6 3/
8 in.),
cone type
Enclosure type
Advanced SAW type
Reproduction frequency range
28 Hz - 200 Hz
Amplifier section
Continuous RMS power output
75 W (8 ohms, 20 Hz -
20 kHz, 0.8% THD)
Inputs
LINE IN (input pin jack)
SPEAKER IN (input terminals)
Outputs
LINE OUT (output pin jack)
SPEAKER OUT (output terminals)
General
Power requirements
North American model:
120 V AC, 60 Hz
European model:
220 - 230 V AC, 50/60 Hz
Other models:
110 - 120 V/220-240 V
AC, 50/60 Hz
Power consumptions
70 W
1 W (standby mode)
Dimensions (w/h/d)
Approx. 205
× 385 × 389
mm (8 1/
8 × 15
1/
4 × 15
3/
4
in.), including front grille
Mass
Approx. 10.3 kg
(22 lb 11 oz)
Supplied accessories
SA-VE325
Foot pads (20)
Audio connecting cord (1)
Speaker connecting cords, 10 m (32 ft 9 3/4 in.) (2)
Speaker connecting cords, 3.5 m (11 ft 6 in.) (3)
Speaker connecting cords, 2.5 m (8 ft 2 1/2 in.) (2)
SA-VE322
Foot pads (8)
Audio connecting cord (1)
Speaker connecting cords, 3.5 m (11 ft 6 in.) (2)
Speaker connecting cords, 2.5 m (8 ft 2 1/2 in.) (2)
Design and specifications are subject to change without
notice.


background image
2
SA-VE322/VE325/WMS325/SS-CN325/V325
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The "limit" indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15
µF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground


background image
3
SA-VE322/VE325/WMS325/SS-CN325/V325
SECTION 1
DIAGRAMS
1-1.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
·
: Pattern from the side which enables seeing.
· Abbreviation
AR
: Argentina model
SP
: Singapore model
Note on Schematic Diagram:
· All capacitors are in
µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
· All resistors are in
and 1/4 W or less unless otherwise
specified.
· 2 : nonflammable resistor.
· C : panel designation.
· A : B+ Line.
· B : B­ Line.
· Voltages are dc with respect to ground under no-signal
conditions.
· Voltages are dc with respect to ground in service mode.
no mark : MUSIC MODE
(
) : MOVIE MODE
· Voltages are taken with a VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal produc-
tion tolerances.
· Signal path.
F
: AUDIO
· Abbreviation
AR
: Argentina model
AUS
: Australian model
CH
: Chinese model
CND : Canadian model
MX
: Mexican model
SP
: Singapore model
Note:
The components identi-
fied by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.
· Circuit Boards Location
(SA-WMS325)
MAIN board
POWER board
AUTO POWER board
POWER SWITCH board
CONTROL board
CONNECTOR board
MODE board


background image
4
SA-VE322/VE325/WMS325/SS-CN325/V325
D101
E-5
D102
E-5
D103
D-5
D104
D-5
D301
B-2
D302
B-2
D303
D-2
D304
D-2
D305
F-4
D306
H-3
D501
H-4
D502
D-3
D503
D-3
D701
F-5
D702
F-5
D703
F-4
D704
G-4
IC101
D-5
IC102
B-5
IC103
B-4
IC104
F-5
IC701
G-5
Q101
B-5
Q102
A-5
Q103
A-4
Q104
A-4
Q301
D-2
Q302
C-2
Q303
C-2
Q304
C-3
Q305
C-3
Q306
D-2
Q307
D-3
Q308
F-2
Q309
E-2
Q310
F-2
Q311
F-2
Q701
F-5
Q702
F-5
Q703
H-5
Q704
H-5
Q705
H-5
1-2.
PRINTED WIRING BOARD ­ MAIN Section (SA-WMS325) ­
· See page 3 for Circuit Boards Location.
· Semiconductor
Location
Ref. No.
Location
MAIN BOARD
J101
OUT
OUT
IN
LINE
SPEAKER
TM101
IN
L
R
+
+
+
+
­
­
­
­
POWER SAVE
AUTO
OFF
S701
(11)
11
1-680-777-
T501
POWER
TRANSFORMER
SP1
A
CONNECTOR BOARD
CN202
E
AUTO POWER
BOARD
CN604
B
POWER BOARD
CN401
C
AUTO POWER
BOARD
CN605
D
POWER SWITCH
BOARD
CN801
A
B
C
D
E
F
G
H
I
J
K
L
1
2
3
4
5
6
IC102
IC103
IC101
IC104
IC701
(Page 7)
(Page 7)
(Page 8)
(Page 8)
(Page 8)


background image
SA-VE322/VE325/WMS325/SS-CN325/V325
5
5
1-3.
SCHEMATIC DIAGRAM ­ MAIN Section (SA-WMS325) ­
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que
par une pièce portant le numéro spécifié.
(Page 6)
(Page 9)
(Page 9)
(Page 6)
(Page 9)