COLOR VIDEO CAMERA
SSC-DC593
SSC-DC593P
SSC-DC598P
SERVICE MANUAL
1st Edition
SSC-DC593/DC593P/DC598P (E)
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin
de réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les
réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres.
Pour toute réparation faire appel à une personne compétente uniquement.
1
SSC-DC593/DC593P/DC598P (E)
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 5
Related manuals ......................................................................................................... 5
1. Service Overview
1-1.
Board Location ............................................................................................ 1-1
1-2.
Installation and Removal of Cabinet ........................................................... 1-1
1-2-1.
Upper Case ................................................................................. 1-1
1-2-2.
Front Assembly .......................................................................... 1-2
1-2-3.
Rear Assembly ........................................................................... 1-2
1-3.
Installation and Removal of Board ............................................................. 1-3
1-3-1.
PR-269 Board ............................................................................. 1-3
1-3-2.
FC-92 Board ............................................................................... 1-4
1-3-3.
CT-221 Board ............................................................................. 1-4
1-4.
Motor Assembly/Optical Shutter Block/Installation and Removal of CCD
Assembly ..................................................................................................... 1-5
2. Circuit Description
2-1.
BI-156 Board ............................................................................................... 2-1
2-2.
PR-269 Board .............................................................................................. 2-1
2-2-1.
Main Signal Processing Circuit .................................................. 2-1
2-2-2.
Microcomputer's Peripheral Circuit .......................................... 2-1
2-2-3.
CCD Drive Pulse Signal Circuit ................................................ 2-1
2-2-4.
External Sync Circuit ................................................................. 2-2
2-2-5.
DC Servo Circuit ........................................................................ 2-2
2-2-6.
Motor Drive Circuit .................................................................... 2-2
2-2-7.
Character Generator Circuit ....................................................... 2-2
2-3.
FC-92 Board ................................................................................................ 2-3
2-3-1.
RS-485 Communication Circuit ................................................. 2-3
2-3-2.
Function Selection Switches ...................................................... 2-3
2-3-3.
I/O Sircuit ................................................................................... 2-3
2-3-4.
CT-221 Board ............................................................................. 2-3
3. Adjustment
3-1.
Preparations ................................................................................................. 3-1
3-1-1.
Adjusting Fixtures and Measurement Equipment ...................... 3-1
3-1-2.
Connection Diagram .................................................................. 3-2
3-1-3.
Camera Adjustment Commander ............................................... 3-2
3-1-4.
Adjustment Commander Relay Tool ......................................... 3-3
3-1-5.
Selection Flowchart of Adjustment Required Items .................. 3-3
2
SSC-DC593/DC593P/DC598P (E)
3-2.
Adjustment Procedure ................................................................................. 3-3
3-2-1.
Preparation for Adjustment ........................................................ 3-3
3-2-2.
Writing of Initial Data ................................................................ 3-4
3-3.
Camera Adjustment ..................................................................................... 3-4
3-3-1.
Adjusting Mode Setting ............................................................. 3-4
3-3-2.
fsc Adjustment ........................................................................... 3-4
3-3-3.
57 MHz Adjustment ................................................................... 3-5
3-3-4.
VCO Adjustment ........................................................................ 3-5
3-3-5.
Burst Level Adjustment ............................................................. 3-5
3-3-6.
SET UP Adjustment ................................................................... 3-5
3-3-7.
WB Adjustment (3200K Preset and WB Data Reading) ........... 3-6
3-3-8.
Color Reproduction Adjustment ................................................ 3-6
3-3-9.
WB Data Reading ...................................................................... 3-7
3-3-10. Data Writing ............................................................................... 3-7
3-4.
Confirmation after Adjustment ................................................................... 3-8
3-4-1.
Preparation for Confirmation ..................................................... 3-8
3-4-2.
Menu Operation ......................................................................... 3-8
3-5.
Confirmation ............................................................................................... 3-8
3-5-1.
Confirmation of fsc Adjustment ................................................. 3-8
3-5-2.
Confirmation of 57 MHz Adjustment ........................................ 3-8
3-5-3.
Confirmation of VCO Adjustment ............................................. 3-9
3-5-4.
Confirmation of Burst Level Adjustment .................................. 3-9
3-5-5.
Confirmation of SET UP Adjustment ........................................ 3-9
3-5-6.
Confirmation of WB Adjustment (3200K Preset and WB Data
Reading) ..................................................................................... 3-9
3-6.
Defect Correction Setting Procedure ........................................................ 3-10
4. Spare Parts
4-1.
Notes on Repair Parts .................................................................................. 4-1
4-2.
Exploded Views .......................................................................................... 4-2
4-3.
Electrical Parts List ..................................................................................... 4-6
4-4.
Parts List for Frame ................................................................................... 4-11
4-5.
Packing Materials & Supplied Accessories .............................................. 4-11
5. Semiconductor Pin Assignments
6. Block Diagrams
Overall .................................................................................................... 6-1
Overall (for SSC-DC593/DC593P) .......................................................... 6-2
Overall (for SSC-DC598P) ....................................................................... 6-3
3
SSC-DC593/DC593P/DC598P (E)
7. Schematic Diagrams
BI-156
.................................................................................................... 7-1
CT-221 .................................................................................................... 7-2
FC-92
.................................................................................................... 7-3
PR-269 .................................................................................................... 7-4
8. Board Layouts
BI-156
.................................................................................................... 8-1
CT-221 .................................................................................................... 8-1
FC-92
.................................................................................................... 8-2
PR-269 .................................................................................................... 8-4