background image
Setup Procedures
Unpacking
When you unpack the unit, make sure that all the following are accounted for.
· Router Unit
· Wireless Unit
(Broadband Router Unit PCWA-R1)
(Wireless LAN Access Point PCWA-A820)
* The Wireless Unit has Access Point functions.
· AC Adapter
· Power cord
· Read This First
· Quick Start Guide (this document)
· Troubleshooting Guide
· Limited Warranty
Continued on next page
Confirm the connection method of the wireless connection on
the computer.
Refer to the documentation provided with your wireless LAN PC card or Wireless LAN
Converter to confirm the connection method of the computer to the Access Point when
using a wireless LAN PC card or Wireless LAN Converter.
If using a wireless LAN PC card with the Windows XP operating system, connect to the
network using the Windows XP Wireless Network function.
Configure the TCP/IP settings for the Wireless Network
connection on the computer.
Configure the TCP/IP settings on the computer as follows.
· IP address setting: Select "Obtain an IP address automatically".
· DNS setting: Select "Disable DNS" in the Windows Me operating system.
Select "Obtain a DNS server address automatically" in the Windows 2000
and Windows XP operating systems.
Prepare the Ethernet cable to connect the Router Unit and
ADSL or cable modem.
z Hint
Use a straight-through or cross-over Ethernet cable.
Configure the computer firewall or proxy settings
If you are using the Windows XP Internet Connection Firewall or another personal
firewall, you may need to change the security level setting. To display the Router Unit
Setup Page or Access Point Setup Page, you may also need to change the proxy settings
of your Web browser. Refer to "Miscellaneous", "Case 4: Computer firewall function and
browser proxy settings" in the separate Troubleshooting Guide for details.
Enable the Java settings of your Web browser
Wireless LAN Security
Making security settings for the wireless LAN is extremely important. Sony assumes no
responsibility for any security problems that may arise from the use of the Wireless
LAN.
Procedure
2
Check
Connect each unit and turn the power on
Connect each unit as shown in the next figure, and turn the power on.
1 Use an Ethernet cable to connect the cable or DSL modem to the WAN connector of the
Router Unit.
2 Connect the Wireless Unit to a Wireless Unit/LAN connector.
z Hint
There are two Wireless Unit/LAN connectors. Use either one.
3 Connect the AC Adapter to the Router Unit, and turn the AC Adapter on.
4 Connect an end of the Ethernet cable to a LAN connector of the Router Unit.
5 Connect the other end of the Ethernet cable to your computer.
z Hint
The Ethernet port of your computer is on its back panel.
Internet
When you turn the power on, confirm that the Status indicators on the Wireless Unit and
Router Unit change as follows before proceeding to Procedure 3.
Wireless Unit: Changes from a quickly flashing white light to a slowly flashing one.
Router Unit: Change from flashing white light to a steadily lit one.
Establish Wireless Connections
Procedure
3
Check
Establish communications between
the computer and the Access Point
This description assumes that the connection is
established with factory default settings.
Access Point factory default settings
Network Name (SSID):
The 6-character identifier printed on the label inside the rear
cover of the Wireless Unit
Security settings
Encryption (WEP):
Disabled
IEEE 802.11 Mode:
11g, 11b (High multicast rate)
Confirming the network name (SSID)
Configure the wireless communication settings on the computer, and then establish
communications between the computer and the Access Point.
Refer to the instructions for your wireless LAN PC card or Wireless LAN Converter for the
setting method.
z Comments
· The network name (SSID) may also be called something like the "ESSID" or "network ID", depending on
the particular device.
· Encryption may also be called something like "encoding" or "security", depending on the particular device.
Router Unit Setup
Procedure
4
Check
Display the Router Unit Setup Page
Access the Access Point from a Web browser to display the Router Unit Setup Page.
Compatible browsers:
Internet Explorer 5.5 or later
Netscape 6.1 or later
Note
If the Setup Page does not appear, refer to "Connections", "Case 1: Cannot display the Setup Page (error
message appears)" in the separate Troubleshooting Guide for details about bypassing the proxy server.
Launch the Web browser.
1
Enter http://192.168.11.1/ in the Address field, and press the Enter key.
2
Preparation
Procedure
1
Check
Perform the necessary preparations and
confirmations for connections
Procedure
2
Check
Connect each unit and turn the power on
Establish Wireless Connections
Procedure
3
Check
Establish communications between a computer and
the Access Point
Router Functions Setup
Procedure
4
Check
Display the Router Unit Setup Page
Procedure
5
Check
Configure the Router functions
Each procedure is preceded by a check box. Before proceeding to the next step,
confirm that you have completed all necessary tasks by ticking the box.
Check
Access Point Functions Setup
Procedure
7
Check
Configure the Access Point functions
Preparation
Procedure
1
Check
Perform the necessary preparations
and confirmations for connections
Obtain the information required to make the computer
connections.
The procedure in this guide describes the connection process using the factory
default settings.
The factory default settings of the Access Point function are:
Network Name (SSID):
The 6-character identifier printed on the label inside the rear
cover of the Wireless Unit
Security settings
Encryption (WEP):
Disabled
IEEE 802.11 Mode:
11g, 11b (High multicast rate)
Before setting up the Broadband Router, perform the following.
Set up the wireless LAN PC card or Wireless LAN Converter
Perform the required software installation and settings according to the instructions
provided with your wireless LAN PC card or Wireless LAN Converter to make it
operational.
Ethernet
cable
1
2
Switch`
3
Cable modem or DSL modem
Use either connector.
Configure the Wireless Communication Settings
on the Computer
© 2004 Sony Corporation Printed in Japan
4-680-203-11 (1)
Wireless
Broadband Router
Quick Start Guide
Before reading this guide, be sure to read the "Read This
First" supplement.
This guide describes the preparations and settings
required to connect to the Internet using the Wireless
Broadband Router.
The PCWA-AR800 consists of:
· Broadband Router Unit
PCWA-R1
· Wireless LAN Access Point
PCWA-A820
In this document, we refer to the Broadband Router Unit as the
Router Unit and to the Wireless LAN Access Point as the
Access Point.
The PCWA-AR800 can be used at frequency settings of 2.4 GHz
and 5 GHz. Change this setting as necessary. (By default, the
PCWA-AR800 is set to 2.4 GHz.)
· Sony, VAIO,
,
, and the Eco Info logo are trademarks of Sony Corporation.
· Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
· In this document, Microsoft® Windows® XP Home Edition and Microsoft® Windows® XP Professional are
referred to as Windows XP.
· Netscape is a registered trademark of Netscape Communications Corporation.
· All other names of systems, products and services are trademarks of their respective owners.
· In the document, the TM or ® marks are not specified.
Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil
based ink.
Procedure
6
Check
Display the Access Point Setup Page
Procedure
8
Check
Configure computer settings
PCWA-AR800
4
5
Remove the rear cover
by sliding it in the
direction of the arrow.
This ID is used as the default
network name (SSID).
z Hint
The IP address 192.168.11.1 is the Router Unit
factory default. If the Router's IP address has
been changed, contact your network
administrator.
The Router Unit Setup Page appears.
z Hint
Clicking
or
displays Help.
The following procedures describe the setup process using "Easy Setup".


background image
Access Point Function Setup
Procedure
6
Check
Display the Access Point Setup Page
Click "Scan".
1
Access Points are searched for, and any discovered Access Points are displayed in the list.
Select the Access Point to configure, and click the "Access Point Setup" button.
2
A user name and password input dialog box appears.
In the user name text box, enter "admin", and then click "OK".
3
z Hint
· The default password is "admin".
· Leave the "Password" text box blank.
The Access Point Setup Page appears in a new window.
The Setup Completed window appears.
3
Close the Web browser.
Note
When you change the wireless settings, the connection to the Access Point is severed. After performing
procedure 7, make sure that you perform procedure 8 to reestablish the connection.
Configure the Wireless Communication
Settings on the Computer
Procedure
8
Check
Configure computer settings
Configure the wireless communication settings on the computer used for the setup to match
the Access Point settings.
Configure the network name (SSID) and security settings on the computer to
match those set in procedure 7.
z Hint
Refer to the instructions of your wireless LAN PC card or Wireless LAN Converter for the setting method.
This completes the configuration.
Refer to Help for details about Wireless Broadband
Router settings.
To display Help, click
or
on the Router Unit Setup Page or the
Access Point Setup Page.
Refer to the Read This First supplement for the following
information:
· Safety information
· Installation
· Ethernet cable connection method
· Reset to factory defaults
· Factory default settings
· Status Indicator indications
Procedure
5
Check
Configure the Router functions
Configure the Router functions of the Router Unit.
The basic settings to connect to the Internet are described here. For details about the settings,
refer to Help on the Router Unit Setup Page.
Specific information required to establish an Internet connection is
normally provided by your Internet service provider when making the
service contract. You may have to refer to this information when setting up
the connection, so have the information at hand.
Note
Depending on your Internet service provider, you may not be allowed to connect a router type access point to
your DSL or cable modem. Refer to the provisions of the contract with your Internet service provider for
details.
Click "Easy Setup".
1
The Wireless Broadband Router setup wizard starts.
Follow the instruction on the screen to complete the setup.
2
z Hint
If the administrator password is configured in step 2 of the Easy Setup, a user name and password input
dialog box appears.
Enter the administrator user name and password to proceed.
When setup is complete, the following screen appears.
Proceed to procedure 6 to configure the Access Point.
Procedure
7
Check
Configure the Access Point functions
The wireless functions are set in the Wireless Unit. The basic wireless connection settings are
described here. For details about the settings, refer to Help the Access Point Setup Page.
Click "Easy Setup".
1
The Easy Setup Page appears.
Configure settings.
2
1
Enter the network name (SSID).
The network name (SSID) is an ID that serves to identify the wireless network. You should enter up
to 32 characters. Permissible characters are letters, numbers, and symbols.
Note
Do not forget the network name (SSID).
2
Set "Encryption (WEP)" to "Enable".
z Hint
Encryption (WEP) encodes wireless communications and prevents unauthorized access to the network.
The encryption key is the password required for WEP communications on an encrypted network.
3
Select "Key Length".
4
Enter the encryption key, and re-enter it again at "WEP Key (Confirmation)"
If you select "40 bits" for the "Key Length", enter up to five letters, numbers and symbols. If you
select "104 bits" for the "Key Length", enter up to 13 letters, numbers and symbols.
Note
Do not forget the encryption key.
5
Select the "IEEE 802.11 Mode".
Check that the settings are correct, and click "Execute Setup".
3
1
When finished making settings, click "Next".
The Setup Confirmation window appears.
2
Check that the settings are correct, and click "Execute Setup".
2
3
4
1
When satisfied with the displayed
settings, click here.
If you want to modify the settings, click here to return to the previous window.
If you do not want to configure the Access Point, click here.
Enter "admin" here.
Enter the administrator password here,
as set in step 2 of the Easy Setup.
Enter "admin" here.
Leave this text box blank.
5