Conf
idential
PCG-FR130
SERVICE MANUAL
NOTEBOOK COMPUTER
9-876-046-02
For American Area
US Model
Canadian Model
Lineup : PCG-FR130
· Design and specifications are subject to
change without notice.
Ver 2-2003C
Revision History
S400
-- 2 --
Information in this document is subject to change without notice.
Sony, VAIO and CLIE are trademarks or registered trademarks of
Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf
and other Microsoft products are trademarks or registered trademarks
of Microsoft Corporation in the United States and other countries.
The word Bluetooth and the Bluetooth logo are trademarks of
Bluetooth SIG, Inc. AMD, the AMD logo, other AMD product names
and combinations thereof are trademarks of Advanced Micro
Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks
or registered trademarks of Intel Corporation. Transmeta, the
Transmeta logo, Crusoe Processor, the Crusoe logo and
combinations thereof are trademarks of Transmeta Corporation in
the USA and other countries. Graffiti, HotSync, PalmModem, and
Palm OS are resistered trademarks, and the Hotsync logo and Palm
are trademarks of Palm, Inc. or its subsidiaries. (M) and Motrola
are trademarks of Motrora, Inc. Other Motrola products and services
with (R) mark like Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and services in this manual
are trademarks or registered trademarks of their respective owners.
In this manual, the (TM) or (R) mark are not specified.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as well
as all precautions listed in the operating manual and other associated
documents.
2. Use designated parts only
The set's components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the 0 mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3. Always follow the original design when mounting
parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts or
routing wires, therefore, be sure to duplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6. When handling flexible print boards...
· The temperature of the soldering-iron tip should be about 270C.
· Do not apply the tip more than three times to the same pattern.
· Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
Caution Markings for Lithium/Ion Battery - The following or similar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Discard used batteries according to the
manufacturer's instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat
above 100
°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
· Overcharging, short circuiting, reverse charging, multilation or
incineration of the cells must be avoided to prevent one or more of
the following occurrences; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface temperature.
· If a cell has leaked or vented, it should be replaced immediately
while avoiding to touch it without any protection.
PCG-FR130 (AM)
Confidential
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
-- 3 --
TABLE OF CONTENTS
Section
Title
Page
PCG-FR130 (AM)
Confidential
CHAPTER 1. BLOCK DIAGRAM ............................... 1-1
(to 1-2)
CHAPTER 2. FRAME HARNESS DIAGRAM ........ 2-1
(to 2-2)
CHAPTER 3. EXPLODED VIEWS AND
PARTS LIST ............................................ 3-1
3-1. Main Section .................................................................... 3-2
3-2. LCD Section Made by HI .......................................... 3-5
3-3. Connector Section (CH Type Only) ................................. 3-7
(to 3-8)
CHAPTER 4. OTHERS
4-1. Replacing the CPU .......................................................... 4-1
1. Removing the CPU .......................................................... 4-1
2. Installing the CPU ............................................................ 4-1
History of the changes is shown as the
"Revision History" at the end of this data.
Confidential
PCG-FR130 (AM)
(END)
1-2
1-1
CHAPTER 1.
BLOCK DIAGRAM
462 PIN PGA
SOCKET A
KT266A-VT8366A
CRT
LCD
SLOT0/1
VT8235
ICS94228
RICOH 5C554
CARDBUS+1394LINK/PHY
SO-DIMM 1/2
CLOCK GENERATOR
SOUTH BRIDGE
NORTH BRIDGE
1394
RJ11
CTRL
SIGNAL
DATA
ADDRESS
DRAM SIGNAL
R/G/B
LVDS SIGNAL
PCI BUS
USB*3
INT.SPKR.
AD1981A
EXT.MIC.
TPA0142
POWER SWITCH BOARD
DC/DC BOARD
POWER SWITCH
BATTERY
MAXIM 1717
MAXIM 1632
CPU-VCC_CORE
3V/3VSUS
5V/5VSUS
POWER CIRCUIT
DC JACK
VIN
MOTHER BOARD
AC
LINK1
AC
LINK2
MDC
TOUCH
PAD
PCI CLOCK
USB CLOCK
CPU CLOCK
14M CLOCK
T/P BOARD
T/P SWITCH
AMD
ATHLON 35W
Nvidia
Squish17V
AGP
TV
TV SIGNAL
LPT
FDD
RJ45
MBX-80
DDR VRAM
16MB
K/B LED
USB
SIGNAL*3
NS PC87391
SUPER I/O
Realtek
PWS-26
SWX-127
SWX-128
LPC
ICS93712
CLOCK BUFER
DDR CLOCK
DDR
VLNK
SIGNAL
XBUS
NS PC87570
PCU
BIOS
INT.K/B
SECONDARY
IDE
BUS
PRIMARY
IDE
BUS
HDD
CDROM
RTL8100BL
EXT.SPKR.
WIRELESS SWITCH
HDD LED
Bettery LED
Power LED
Confidential
PCG-FR130 (AM)
(END)
2-2
2-1
CHAPTER 2.
FRAME HARNESS DIAGRAM
PRINTER
MONTOR
USB
USB
USB
DC-IN
PHONE
AV OUT
NETWORK
IEEE 1394 i.LINK
EXTERNAL
MICROPHONE
HEADPHONE
L Side
Rear Panel
KEY BOARD
RAM
DDR SO-DIMM
SLOT A
BATTERY PACK
PCN3
81
CON8
CON11
CON5
CON6
PCN1
CON4
CON10
CON23
SWX-127 Board
(Side-A)
PWS-26 Board
(Side-A)
SWX-128 Board
(Side-A)
MBX-80 Board
(Side-A)
PCN2
CON19
CON2
CON3
CON1
CON13
CON15
CON14
CON25
CON24
CON17
CON20
CON7
CON22
CON21
CON12
PC CARD
CONNECTOR
DC FAN
200
199
2
1
200
199
2
1
225
124
PCN2
PCN1
1
2
59
60
28
17
JP2
JP1
112
18
PAD, TOUCH
FLOPPY DISK DRIVE
HARD DISK
Optical DRIVE
13
1
2
59
60
26
27
1
52
2
1
50
49
2
1
1
2
21
22
30
29
2
1
12
A77
A1
B1
B77
1
2
JP3
JP1
1
2
CON1
1
21
22
2
SPEAKER
1
2
29
30
J1
J2
1
2
CARD, MODEM
LCD
INVERTER
LCD HARNESS
LCD Block
From board to connector (direct connection)
Harness (connector at both end)
Harness (soldered at one end)
Connectors soldered on board and appearing on the panel
CON9