background image
Marine Pack
3-065-038-11(1)
MPK-P1
Sony Corporation © 2000 Printed in Japan
F
Owner's Record
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer
regarding this product.
Model No. MPK-P1
Serial No.
Operating Instructions
Mode d'emploi
Manual de instrucciones
Gebruiksaanwijzing
English
Français
English
Main Feature
Useable at a depth of up to 30 meters (98 feet) underwater.
This marine pack MPK-P1 is exclusively for use with the Sony Digital Still
Camera DSC-P1, enabling the digital still camera to be used in the rain or
snow or at the beach as it is water-resistant.
For instructions on using your digital still camera with this pack, refer to
the operating instructions of the digital still camera.
Notice
·Before using the digital still camera underwater, first take the marine pack
to a depth of about 1 m (3.3 feet) and check that the digital still camera is
operating properly and that the marine pack is not leaking, then
commence your dive.
·In the unlikely event that a malfunction of the marine pack causes damage
due to water leakage, Sony does not guarantee against damages to the
equipment contained in it (digital still camera, battery, etc.) and the
recorded contents, nor expenses entailed in the photography.
Precautions
·Do not subject the front glass to strong shock, as it may crack.
·Avoid opening the marine pack at the beach or on the water. Preparation
such as installing the digital still camera and changing the "Memory
Stick" should be done in a place with low humidity and no salty air.
·Do not throw the marine pack into the water.
·Avoid using the marine pack in places with strong waves.
·Avoid using the marine pack under the following situations:
­ in a very hot or humid place.
­ in water hotter than 40°C (104°F).
­ at temperatures lower than 0°C (32°F).
In these situations moisture condensation or water leakage may occur and
damage the equipment.
·Use the marine pack for no longer than 30 minutes at a time in
temperatures above 35°C (95°F).
·Do not leave the marine pack under direct sunlight in a very hot and
humid place for a long period of time. If you cannot avoid leaving the
marine pack under direct sunlight, be sure to cover the pack with a towel
or other protection.
Water leakage
If water happens to leak in, stop exposing the marine pack to water
immediately.
If the digital still camera gets wet, take it to the nearest Sony dealer
immediately.
Anti-fogging lens solution
Coat the surface of the glass with the supplied anti-fogging lens solution.
This is effective in preventing fogging.
How to use the anti-fogging lens solution
Apply 1 or 2 drops of cleaner liquid to the inside of the front glass and wipe
evenly to spread the liquid using swabs, a soft cloth or tissue paper.
O-ring A
This equipment uses an O-ring to maintain its water resistance. Please
observe the following points in order to make full use of the O-ring's
function.
Improper handling of the O-ring can result in water leakage.
O-ring maintenance
Damage and cracking in the O-ring can cause water to leak into the marine
pack. You should check the O-ring each time you use the marine pack and
check that there is no damage to its surface and no dust or debris adhering
to it.
·Remove the O-ring with your fingers. Do not use pointed or metal
objects, since they may damage the seating groove on the marine pack.
·Make sure that the O-ring is not twisted when attaching it.
·Make sure that the O-ring is always coated lightly with grease. The grease
protects the O-ring and prevents wear.
·Spread out the grease evenly with your finger, or place the O-ring and a
small amount of grease in a plastic bag and knead it gently with both
hands. Do not use paper or cloth, since fibers may adhere to the O-ring.
You can obtain grease (no. 2-115-921-01) at your Sony dealer.
When closing the marine pack body
Make sure that the O-ring has not slipped out of the seating groove.
Pinching the O-ring may not only damage it but also may cause water to
leak into the marine pack.
O-ring serviceable life
The serviceable life of an O-ring varies with the frequency of use of the
marine pack and storage conditions, but generally it is about one year.
You can obtain O-rings (no. 3-065-033-01) at your Sony dealer.
O-ring storage
Keep spare O-rings (not supplied) in a cool location not exposed to direct
sunlight. Do not bend them or place heavy objects on top of them.
Checking for water leakage after replacing the O-ring
Check for water leakage before installing the digital still camera.
Close the marine pack without installing the digital still camera, and keep
the marine pack submerged under water at a depth of about 15 cm (6
inches) for about 3 minutes and then check for water leakage.
Maintenance
After recording
·After recording in a location subject to sea breezes, wash the marine pack
with fresh water to remove salt and sand with the buckles fastened
thoroughly, then wipe with a soft dry cloth. It is recommended that you
submerge the marine pack in fresh water for about 30 minutes. If it is left
with salt on it, metal portions may be damaged or rust may form and
cause water leakage.
·If you get suntan lotion or other greasy substances on your marine pack,
wash it off with tepid water.
·Clean the inside of the pack with a soft dry cloth. Do not wash the inside
of the pack. Please be sure to perform the above maintenance each time
you use the marine pack. Do not use any type of solvent such as alcohol,
benzine or thinner for cleaning, as this might damage the finish.
When storing the marine pack
·Attach the spacer supplied with your marine pack to prevent wear of the
O-ring. (See illustration B.)
·Prevent dust from collecting on the O-ring.
·Lightly coat the O-ring with grease and insert it into the seating groove,
then store the marine pack in a cool, well-ventilated location. Do not
fasten the buckle.
·Avoid storing the marine pack in a cold, very hot or humid place, or
together with naphthalene or camphor, as these conditions might damage
the unit.
Preparation
Preparing the digital still camera
For details, please refer to the operating instructions supplied with your
digital still camera DSC-P1.
1 Remove the wrist strap from the digital still camera DSC-P1.
2 Install the battery pack.
Be sure to use a fully charged battery pack.
3 Insert the "Memory Stick".
4 Turn on the POWER of the digital still camera.
5 Turn on the LCD screen.
6 Set all the adjustments of the digital still camera to automatic
mode.
D Installing the digital still camera
1 Turn off the POWER.
2 Set the Mode selector of the digital still camera to MOVIE.
(D-2)
3 Set the Mode selector on the marine pack to MOVIE. (D-3)
4 Release the buckle.
Open the side body by sliding the lock lever (1) and releasing the buckle in the
direction of the arrow 2, 3. (D-4-1)
The black rubber part is a spacer. Keep the spacer since you will need it to store the
marine pack.
5 Prepare the marine pack.
1
Coat the O-ring with grease.
Clean off any sand or other debris that is on the O-ring, in the seating groove, or
on the main body where it touches the O-ring. Coat the O-ring with a light,
even layer of grease.
If the cover is closed with sand or other debris adhering to these places, the
main body may be damaged or water may leak into the marine pack.
2
Coat the front glass with anti-fogging lens solution.
Coat the surface of the glass on the front of the marine pack with the supplied
anti-fogging lens solution.
6 Install the digital still camera.
Check that the lens and the LCD screen is clean before installing the digital still
camera.
7 Close the side body.
Secure the side body, and fasten the buckle until it clicks.
Caution
When closing the marine pack body, make sure that there is no debris, sand, hair,
or any other foreign matter on the O-ring or in the seating groove. Water leakage
may result if any such foreign matter is caught in these places.
Neck strap E
Attach the supplied neck strap before using the marine pack.
Using the Marine Pack
F Recording
1 Turn on the POWER.
Check that the Mode selector operates normally.
2 Set the Mode selector to the desired mode and press the
shutter button.
You can record pictures while looking at the LCD screen or through the finder.
To record still images, set to STILL.
To record moving images, set to MOVIE. (Sound cannot be recorded while
recording moving images.)
For details, refer to the operating instructions supplied with your digital still
camera.
Using various functions G
You can use the various functions of the digital still camera installed in the
marine pack.
1
Use the flash
2
Record images in macro
3
Adjust various settings
Use the zoom H
Press the zoom button.
When using the finder to record, the zoom button will produce eclipse in
the image in the finder, but it has no effect on the recorded image.
1
Press on the W side for wide-angle. (Subject appears farther away.)
2
Press on the T side for telephoto. (Subject appears closer.)
Caution
If you do not operate the camera for over three minutes during recording,
the camera turns off automatically to prevent the battery from wearing
down. To use the camera again, slide the POWER switch to on.
I Playing back with the control button
You can play back images on the LCD screen using the control button. You
cannot hear the sound.
1 Turn on the POWER.
2 Set the Mode selector to PLAY.
3 Select the desired image with the control button.
For details, refer to the operating instructions supplied with your digital still
camera.
J Removing the digital still camera
1 Turn off the POWER.
Always be sure to turn off the POWER switch when installing or
removing the digital still camera. The lens may be damaged if
the power is left ON.
2 Set the Mode selector on the marine pack to MOVIE.
3 Release the lock lever and open the marine pack.
4 Remove the digital still camera DSC-P1.
Be careful not to drop the digital still camera when removing it.
Caution
Before opening the marine pack, rinse it with tap water or fresh water and
then wipe the water off with a soft cloth. When opening it, be careful not to
let any water from your body, hair, or wetsuit cuffs drip onto the digital
still camera.
Before making a dive
·Before recording images underwater, first take the marine pack to a depth
of about 1 m (3.3 feet) and check that it operates properly and that there
are no leaks, then commence your dive.
·Install the digital camera in the marine pack before diving, and avoid
opening and closing the marine pack while on board boats or at the
seashore as much as possible. When installing the digital camera, do it in
a place that has as low a humidity as possible.
·Before using the marine pack, make sure that no debris has been caught
between the front and back halves of the body.
T
W
MENU
C
D
G
I
J
1
2
3
4
6
1
2
12
12
Times that are suited for recording
The time best suited for recording images is between 10:00 AM and 2:00
PM, when the sun is directly overhead.
To record pictures in places where the sunlight does not reach well or at
night, please use the underwater video light HVL-ML20 (not supplied).
Note
In images recorded underwater, the subject sometimes has a bluish cast. To
correct the color when this happens, use the color filter kit VF-MP1K, which
is available as an optional accessory.
Troubleshooting
Symptom
There are drops of water
inside the marine pack.
The recording and playing
back function does not work.
Specifications
Material
Plastic (PC, ABS), stainless steel, glass
Water-resistance
O-ring, buckle
Pressure-resistance
To a depth of up to 30 m (98 feet) underwater
Switches that can be externally operated
Power, mode, shutter, zoom, flash, macro, control
Dimension
Approx. 150
× 80 × 86 mm (6 × 3 1/4 × 3 1/2 inches) (w/h/d)
Mass
Approx. 300 g (11 oz) (marine pack only)
Supplied accessories
Neck strap (1)
Grease (1)
Anti-fogging lens solution (1)
Operating Instructions (1)
Optional accessories
Color filter kit VF-MP1K
Arm kit VCT-MP1K
Underwater video light HVL-ML20 (must be used together with arm kit
VCT-MP1K, "InfoLITHIUM" (L series) battery pack and L series battery
charger)
Design and specifications subject to change without notice.
Shutter button
Déclencheur
Mode selector
Sélecteur Mode
Power switch
Commutateur
d'alimentation
Front glass
Verre avant
Buckle
Fermoir
Spacer (remove to use the
marine pack)
Entretoise (à retirer avant
d'utiliser le Marine Pack)
Lock lever
Levier de
verrouillage
Hook for neck strap
Crochet pour
courroie de cou
Tripod receptacle
Douille de
trépied
Zoom buttons
Touches Zoom
Control buttons
Touches de
commande
(flash) button
Touche
(flash)
(MACRO) button
Touche
(MACRO)
Select
Sélection
Enter
Validation
12
1
2
3
E
H
Cause/Corrective Actions
· The buckles are not fastened.
b Fasten the buckles until they click.
· The O-ring is not set correctly .
b Place the O-ring evenly in the groove.
· There are scratches or cracks on the O-ring.
b Replace the O-ring with a new one.
· The battery pack has run out.
b Charge the battery pack fully.
· The "Memory Stick" is full.
b Insert another "Memory Stick" or erase
unneeded data from the "Memory Stick."
· The write-protect tab on the "Memory Stick"
is set to LOCK.
b Set the tab to the recording position or
insert a new "Memory Stick."
B
Caractéristique principale
Utilisable jusqu'à une profondeur de 30 mètres sous l'eau.
Le Marine Pack MPK-P1 est exclusivement destiné à l'appareil photo
numérique Sony DSC-P1. Il vous permet d'utiliser le DSC-P1 sous la pluie,
sous la neige et à la plage car il le protège contre l'eau.
Pour les instructions d'utilisation de votre appareil photo numérique avec
le Marine Pack, consultez son mode d'emploi.
Avertissement
·Avant de plonger pour une prise de rues sous-marine, immergez le
Marine Pack à 1 mètre sous l'eau environ et assurez-vous que l'eau ne
s'infiltre pas à l'intérieur et que l'appareil photo numérique fonctionne
correctement.
·Dans le cas très improbable où une anomalie du Marine Pack causerait
des dommages dus à une infiltration d'eau, notez que la garantie Sony ne
couvre pas les dommages au matériel (appareil photo numérique, batterie,
etc.) à l'intérieur du Marine Pack, le contenu enregistré ou les frais
encourus pour la prise de vues.
Précautions
·Ne soumettez pas le verre avant à des chocs importants car il pourrait se
fendre.
·N'ouvrez pas le Marine Pack sur la plage ou dans l'eau. Les opérations
préparatoires telles que la mise en place de l'appareil photo numérique et
le changement de "Memory Stick" doivent être effectuées à l'abri de
l'humidité et de l'air salin.
·Ne jetez pas le Marine Pack dans l'eau.
·N'utilisez pas le Marine Pack par fortes vagues.
·N'utilisez pas le Marine Pack dans les conditions suivantes :
­ dans un endroit très chaud ou humide,
­ dans de l'eau chaude à plus de 40°C,
­ à des températures inférieures à 0°C.
Dans de telles conditions, le matériel pourrait être endommagé par une
condensation d'humidité ou une infiltration d'eau.
·N'utilisez pas le Marine Pack plus de 30 minutes d'affilée par une
température supérieure à 35°C.
·Ne laissez pas longtemps le Marine Pack en plein soleil dans un endroit
très chaud et humide. Si vous ne pouvez éviter de le laisser au soleil,
recouvrez-le d'une serviette ou d'une autre protection.
Infiltration d'eau
Si de l'eau s'infiltre dans le Marine Pack, arrêtez immédiatement de
l'exposer à l'eau.
Si l'appareil photo numérique est mouillé, portez-le immédiatement chez le
revendeur Sony le plus proche.
Liquide antibuée pour objectif
Passez du liquide antibuée pour objectif fourni sur le verre. Ce produit
empêche efficacement la formation de buée.
Comment utiliser le liquide antibuée pour objectif
Mettez 1 ou 2 gouttes de liquide sur la face intérieure du verre avant et
étalez-le uniformément à l'aide d'un coton-tige, d'un tissu doux ou de
papier de soie.
Joint torique A
Le joint torique du Marine Pack assure l'étanchéité du boîtier. Pour qu'il
soit efficace, vous devez observer les points ci-dessous.
Une mauvaise manipulation du joint torique peut provoquer une
infiltration d'eau.
Entretien du joint torique
Si le joint torique est endommagé ou fendillé, de l'eau peut s'infiltrer dans
le Marine Pack. Avant chaque utilisation du Marine Pack, assurez-vous que
le joint torique n'est pas endommagé et ne comporte pas de dépôts de
poussière ou saletés.
·Retirez le joint torique avec les doigts. Ne le retirez pas avec un
instrument pointu ou métallique car vous risqueriez d'endommager la
gorge du boîtier.
·Ne tordez pas le joint torique en le posant.
·Veillez à ce que le joint torique soit toujours recouvert d'une légère couche
de graisse. La graisse le protège et empêche son usure.
·Étalez la graisse uniformément avec le doigt ou placez le joint torique avec
une petite quantité de graisse dans un sac en plastique et pétrissez-le
doucement avec les deux mains. N'utilisez pas de papier ou de tissu pour
étaler la graisse car leurs fibres pourraient adhérer au joint torique.
Vous pourrez vous procurer la graisse (n° 2-115-921-01) chez votre
revendeur Sony.
Lorsque vous refermez le boîtier du Marine Pack
Assurez-vous que le joint torique n'est pas délogé de la gorge du boîtier. S'il
est pincé, non seulement il subira des dommages, mais de l'eau pourra
s'infiltrer dans le Marine Pack.
Durée de service du joint torique
La durée de service du joint torique varie avec la fréquence d'utilisation du
Marine Pack et les conditions de stockage. Elle est généralement de 1 an.
Vous pourrez vous procurer des joints toriques (n° 3-065-033-01) chez votre
revendeur Sony.
Stockage des joints toriques
Rangez les joints toriques de rechange (non fournis) dans un endroit frais à
l'abri des rayons directs du soleil. Ne les pliez pas et ne placez pas d'objets
lourds au-dessus.
Vérification de l'étanchéité du boîtier après le
remplacement du joint torique
Avant de mettre en place l'appareil photo numérique, assurez-vous qu'il
n'y a pas d'infiltration d'eau dans le boîtier.
Fermez le Marine Pack sans appareil photo numérique à l'intérieur,
plongez-le sous l'eau à une profondeur de 15 cm environ pendant
approximativement 3 minutes, puis vérifiez s'il n'y a pas d'infiltration
d'eau.
Entretien
Après la prise de vues
·Après une prise de vues dans un endroit soumis à la brise marine, lavez le
Marine Pack à l'eau douce avec les fermoirs correctement verrouillés pour
en faire partir le sel et le sable, puis essuyez-le avec un chiffon doux et sec.
Il est recommandé de plonger le Marine Pack dans de l'eau douce
pendant 30 minutes environ. Ne laissez pas de sel dessus car il pourrait
attaquer les parties métalliques et de la rouille risquerait de se former et
causer une infiltration d'eau.
·Si vous avez mis de la crème solaire ou une autre substance grasse sur le
Marine Pack, lavez celui-ci à l'eau tiède.
·Nettoyez l'intérieur du Marine Pack avec un chiffon doux et sec. Ne lavez
pas l'intérieur. Effectuez les opérations d'entretien ci-dessus après chaque
utilisation. N'utilisez pas de solvants tels qu'alcool, benzine ou diluant
pour le nettoyage car de telles substances peuvent attaquer la finition.
Lors du stockage du Marine Pack
·Posez l'entretoise fournie avec le Marine Pack pour protéger le joint
torique contre l'usure. (Voir l'illustration B.)
·Empêchez l'accumulation de poussière sur le joint torique.
·Passez une légère couche de graisse sur le joint torique et insérez-le dans
la gorge du boîtier. Rangez ensuite le Marine Pack dans un endroit frais et
bien aéré. Ne verrouillez pas le fermoir.
·Ne rangez pas le Marine Pack dans un endroit froid, très chaud ou
humide ou avec de la naphtaline ou du camphre. Ceci pourrait
l'endommager.
Préparation
Préparation de l'appareil photo numérique
Pour plus d'informations, consultez le mode d'emploi de l'appareil photo
numérique DSC-P1.
1 Retirez la dragonne de l'appareil photo numérique DSC-P1.
2 Mettez la batterie en place.
Utilisez une batterie complètement chargée.
3 Insérez le "Memory Stick".
4 Mettez l'appareil photo numérique sous tension (POWER).
5 Allumez l'écran LCD.
6 Placez toutes les fonctions de réglage de l'appareil en mode
automatique.
D Mise en place de l'appareil photo
numérique
1 Mettez l'appareil hors tension (POWER).
2 Placez le sélecteur Mode de l'appareil photo numérique sur
MOVIE. (D-2)
3 Placez le sélecteur Mode du Marine Pack sur MOVIE. (D-3)
4 Déverrouillez le fermoir.
Ouvrez le boîtier en poussant le levier de verrouillage (1) et déverrouillant le
fermoir dans le sens de la flèche 2, 3. (D-4-1)
La pièce en caoutchouc noir est une entretoise. Conservez-la car vous en aurez
besoin pour ranger le Marine Pack.
5 Préparez le Marine Pack.
1
Passez de la graisse sur le joint torique.
Nettoyez tout le sable et les autres saletés du joint torique, de la gorge ou de la
surface du boîtier venant en contact avec le joint torique. Passez une légère
couche uniforme de graisse sur le joint torique.
Si vous fermez le boîtier avec du sable ou d'autres saletés sur les parties
indiquées ci-dessus, il pourra être endommagé ou de l'eau risquera de s'infiltrer
à l'intérieur.
2
Passez du liquide antibuée pour objectif sur le verre avant.
Passez du liquide antibuée pour objectif fourni sur le verre avant du Marine
Pack.
6 Mettez l'appareil photo numérique en place.
Avant de mettre l'appareil en place, assurez-vous que l'objectif et l'écran LCD sont
propres.
7 Refermez le boîtier.
Fermez correctement le boîtier et rabattez le fermoir jusqu'à ce qu'il se verrouille.
Attention
Lorsque vous refermez le Marine Pack, assurez-vous qu'il n'y a pas de saletés,
sable, cheveux ou autres corps étrangers sur le joint torique ou dans la gorge du
boîtier. Ceci pourrait provoquer une infiltration d'eau.
Courroie de cou E
Fixez la courroie de cou fournie avant d'utiliser le Marine Pack.
Utilisation du Marine Pack
F Prise de vues
1 Mettez l'appareil sous tension (POWER).
Assurez-vous que le sélecteur Mode fonctionne normalement.
2 Placez le sélecteur Mode sur la position désirée et appuyez sur
le déclencheur.
Vous pouvez effectuer la prise de vues en utilisant l'écran LCD ou le viseur.
Pour enregistrer des images fixes, utilisez la position STILL.
Pour enregistrer des images animées, utilisez la position MOVIE. (Vous ne pouvez
pas enregistrer le son avec des images animées.)
Pour plus d'informations, consultez le mode d'emploi de l'appareil photo
numérique.
Utilisation de diverses fonctions G
Vous pouvez utiliser diverses fonctions de l'appareil photo numérique
installé dans le Marine Pack :
1
flash
2
mode macro
3
réglage de divers paramètres
Utilisation du zoom H
Appuyez sur la touche de zoom.
Lorsque vous utilisez la viseur pour la prise de vues, il se produit une
éclipse sur l'image dans le viseur, mais ceci est sans effet sur l'image
enregistrée.
1
Appuyez sur le côté W pour une prise de vues au grand angle. (Le sujet
s'éloigne.)
2
Appuyez sur le côté T pour une prise de vues au téléobjectif. (Le sujet
s'approche.)
Attention
Si vous n'utilisez pas l'appareil pendant plus de trois minutes lors d'une
prise de vues, il s'éteint automatiquement pour économiser la batterie. Pour
le réutiliser, placez le commutateur POWER sur marche.
I Lecture avec la touche de commande
Vous pouvez visionner les images sur l'écran LCD à l'aide de la touche de
commande. Il n'y a pas de son.
1 Mettez l'appareil sous tension (POWER).
2 Placez le sélecteur de mode sur PLAY.
3 Sélectionnez l'image désirée avec la touche de commande.
Pour plus d'informations, consultez le mode d'emploi de l'appareil photo
numérique.
J Retrait de l'appareil photo numérique
1 Mettez l'appareil hors tension (POWER).
Placez toujours le commutateur POWER sur arrêt avant de mettre
en place ou de retirer l'appareil photo numérique. Si vous laissez
l'appareil sous tension, son objectif risque d'être endommagé.
2 Placez le sélecteur Mode du Marine Pack sur MOVIE.
3 Libérez le levier de verrouillage et ouvrez le Marine Pack.
4 Retirez l'appareil photo numérique DSC-P1.
Veillez à ne pas faire tomber l'appareil en le retirant.
Attention
Avant d'ouvrir le Marine Pack, rincez-le avec de l'eau du robinet ou de
l'eau douce, puis essuyez-le complètement avec un chiffon doux. Lorsque
vous l'ouvrez, veillez à ne pas le mouiller avec l'eau de votre combinaison
de plongée, de vos cheveux ou de votre corps.
Avant de partir en plongée
·Avant de partir faire de la photographie sous-marine, immergez le Marine
Pack à 1 mètre sous l'eau environ et assurez-vous qu'il fonctionne
correctement et que de l'eau ne s'infiltre pas à l'intérieur.
·Installez l'appareil dans le Marine Pack avant de plonger et évitez autant
que possible de l'ouvrir ou de le fermer à bord d'un bateau ou sur la
plage. Installez l'appareil photo numérique dans le Marine Pack dans un
endroit aussi peu humide que possible.
·Avant d'utiliser le Marine Pack, assurez-vous qu'il n'y a pas de saleté
coincée entre les demi-boîtiers.
Meilleur moment de la journée pour la prise
de vues
Le meilleur moment de la journée pour la prise de vues est entre 10 h et
14 h 00 lorsque le soleil est à la verticale.
Pour photographier dans des endroits que le soleil atteint mal ou la nuit,
utilisez la torche de plongée HVL-ML20 (non fournie).
Remarque
Sur les images prises sous l'eau, le sujet peut parfois présenter une
dominante bleue. Pour corriger ce phénomène, utilisez le kit de filtre VF-
MP1K disponible en option.
En cas de problème
Symptôme
Présence de gouttes d'eau à
l'intérieur du Marine Pack.
Les fonctions
d'enregistrement et de lecture
ne fonctionnent pas.
Cause/Remèdes
· Les fermoirs sont mal verrouillés.
b Verrouillez correctement les fermoirs.
· Le joint torique n'est pas correctement en
place.
b Placez le joint torique uniformément dans
la gorge.
· Le joint torique est entaillé ou fendillé.
b Remplacez le joint torique par un neuf.
· La batterie est déchargée.
b Rechargez complètement la batterie.
· Le "Memory Stick" est plein.
b Insérez un autre "Memory Stick" ou
effacez les données inutiles du "Memory
Stick".
· Le taquet d'interdiction en écriture du
"Memory Stick" est sur LOCK.
b Placez le taquet sur la position
d'enregistrement ou insérez un "Memory
Stick" neuf.
Spécifications
Matière
Plastique (PC, ABS), acier inoxydable, verre
Étanchéité à l'eau
Joint torique, fermoir
Résistance à la pression
Jusqu'à une profondeur de 30 m sous l'eau
Commutateurs pouvant être commandés de l'extérieur
Alimentation, mode, déclencheur, zoom, flash, macro, commande
Dimensions
150
× 80 × 86 mm (l/h/p) environ
Poids
300 g environ (Marine Pack seulement)
Accessoires fournis
Courroie de cou (1)
Graisse (1)
Solution antibuée pour objectif (1)
Mode d'emploi (1)
Accessoires en option
Kit de filtre VF-MP1K
Kit de bras VCT-MP1K
Torche de plongée HVL-ML20 (doit être utilisée avec le kit de bras
VCT-MP1K, la batterie "InfoLITHIUM" (série L) et le chargeur de batterie
série L)
La conception et les caractéristiques sont susceptibles d'être modifiées sans
préavis.
D
A
Filter kit mount
Monture pour filtre


background image
Español
Característica principal
Utilizable bajo agua a una profundidad de hasta 30 metros.
Este portacámara subacuático MPK-P1 es para usar exclusivamente con la
cámara digital Sony DSC-P1, y permite utilizarla en días de lluvia o nieve, o
en la playa porque es estanco al agua.
Para ver instrucciones sobre cómo usar la cámara digital con este
portacámara, consulte el manual de instrucciones de la cámara digital.
Aviso
·Antes de utilizar la cámara digital bajo el agua, sumerja primero el
portacámara subacuático a una profundidad de aproximadamente 1
metro y compruebe que la cámara digital funciona debidamente y que el
portacámara subacuático no tiene fugas, y a continuación comience su
buceo.
·En el caso improbable de que un mal funcionamiento del portacámara
subacuático ocasione daños debidos a una fuga de agua, Sony no se
responsabilizará de los daños al equipo alojado en él (cámara digital,
batería, etc.) ni del contenido grabado, ni tampoco de los gastos
relacionados con la fotografía.
Precauciones
·No someta el cristal frontal a golpes fuertes porque podrá agrietarse.
·Evite abrir el portacámara subacuático en la playa o en el agua. Los
preparativos tales como la instalación de la cámara digital y el cambio del
"Memory Stick" deberán realizarse en un lugar de poca humedad y sin
aire salino.
·No arroje el portacámara subacuático al agua.
·Evite utilizar el portacámara subacuático en lugares de fuertes olas.
·Evite utilizar el portacámara subacuático en las situaciones siguientes:
­ en un lugar muy cálido o húmedo.
­ en agua más caliente de 40°C.
­ a temperaturas inferiores a 0°C.
En estas situaciones podrá producirse condensación de humedad o fugas
de agua y dañarse el equipo.
·No utilice el portacámara subacuático durante más de 30 minutos por vez
en temperaturas superiores a los 35°C.
·No deje el portacámara subacuático bajo la luz solar directa en un lugar
muy cálido y húmedo durante largo tiempo. Si no puede evitar dejarlo
bajo la luz solar directa, asegúrese de cubrirlo con una toalla u otra
protección.
Fugas de agua
En caso producirse una fuga de agua al interior, deje de exponer el
portacámara subacuático al agua inmediatamente.
Si se moja la cámara digital, llévela inmediatamente al distribuidor Sony
más cercano.
Líquido antiempañante para objetivos
Cubra la superficie del cristal con el líquido antiempañante para objetivos
suministrado. Esto sirve para evitar el empañamiento.
Modo de utilizar el líquido antiempañante para objetivos
Aplique 1 ó 2 gotas de líquido de limpieza a la parte interior del cristal
frontal y frote uniformemente para extender el líquido utilizando palillos de
cabeza de algodón, un paño suave o pañuelo de papel.
Junta tórica A
Este equipo emplea una junta tórica para mantener su estanqueidad.
Observe los puntos siguientes para sacarle el máximo partido a la función
de la junta tórica.
El manejo incorrecto de la junta tórica puede resultar en fugas de agua.
Mantenimiento de la junta tórica
Los daños o grietas en la junta tórica pueden ocasionar fugas de agua al
interior del portacámara subacuático. Cada vez que utilice el portacámara
subacuático deberá inspeccionar la junta tórica y comprobar que su
superficie no está dañada y que no haya polvo ni residuos adheridos a ella.
·Retire la junta tórica con los dedos. No utilice objetos puntiagudos ni
metálicos, porque podrá dañar la ranura de asiento del portacámara
subacuático.
·Asegúrese de que la junta tórica no esté retorcida cuando la instale.
·Asegúrese de que la junta tórica esté siempre ligeramente recubierta con
grasa. La grasa protege a la junta tórica y evita su desgaste.
·Extienda la grasa uniformemente con el dedo, o ponga la junta tórica y
una pequeña cantidad de grasa en una bolsa de plástico y sóbela
suavemente con ambas manos. No utilice papel ni tejido, porque las fibras
se podrán adherir a la junta tórica.
La grasa (número 2-115-921-01) puede obtenerla en su distribuidor Sony.
Cuando cierre el cuerpo del portacámara subacuático
Asegúrese de que la junta tórica no se haya salido de la ranura de asiento. Si
pellizca la junta tórica no sólo dañará la junta, sino que también podrá
ocasionar fugas de agua en el portacámara subacuático.
Vida de servicio de la junta tórica
La vida de servicio de la junta tórica varía con la frecuencia de uso del
portacámara subacuático y las condiciones de almacenamiento, pero
generalmente es de un año aproximadamente.
Las juntas tóricas (número 3-065-033-01) puede obtenerlas en su
distribuidor Sony.
Almacenamiento de las juntas tóricas
Guarde las juntas tóricas (no suministrada) en un lugar fresco no expuesto a
la luz solar directa. No las doble ni ponga objetos pesados sobre ellas.
Comprobación de la estanqueidad después de sustituir la
junta tórica
Compruebe que no haya fugas de agua antes de instalar la cámara digital.
Cierre el portacámara subacuático sin instalar la cámara digital, y
manténgalo sumergido bajo el agua a una profundidad de unos 15 cm
durante unos 3 minutos y luego compruebe que no haya fugas de agua.
Mantenimiento
Después de grabar
·Después de grabar en un lugar expuesto a brisas marinas, lave el
portacámara subacuático con agua dulce para retirar la sal y la arena con
las hebillas perfectamente abrochadas, y a continuación frote con un paño
suave y seco. Se recomienda sumergir el portacámara subacuático en agua
dulce durante unos 30 minutos. Si se deja sal en él, podrán dañarse las
partes metálicas o formarse óxido y ocasionar fugas de agua.
·Si mancha el portacámara subacuático con bronceador u otras sustancias
grasientas, lávelo con agua tibia.
·Limpie el interior del portacámara subacuático con un paño suave y seco.
No lave el interior del portacámara subacuático. Asegúrese de realizar el
mantenimiento indicado arriba cada vez que utilice el portacámara
subacuático. No utilice ningún tipo de disolvente tal como alcohol,
bencina ni diluyente para limpieza, porque con ello podrá dañar el
acabado.
T
W
MENU
C
D
G
I
J
1
2
4
6
1
2
12
12
Seleccionar
Kiezen
Introducir
Bevestigen
12
1
2
3
F
H
B
A
E
3
Cuando guarde el portacámara subacuático
·Ponga el espaciador suministrado con el portacámara subacuático para
evitar el desgaste de la junta tórica. (Vea la ilustración B.)
·Evite que se acumule polvo en la junta tórica.
·Recubra ligeramente la junta tórica con grasa e insértela en la ranura de
asiento, luego guarde el portacámara subacuático en un lugar fresco y
bien ventilado. No abroche la hebilla.
·Evite guardar el portacámara subacuático en un lugar muy cálido o
húmedo, o junto con naftalina o alcanfor, ya que en estas condiciones se
puede dañar la unidad.
Preparación
Preparación de la cámara digital
Para más detalles, consulte el manual de instrucciones suministrado con la
cámara digital DSC-P1.
1 Retire la correa de muñeca de la cámara digital DSC-P1.
2 Instale la batería.
Asegúrese de utilizar una batería completamente cargada.
3 Inserte el "Memory Stick".
4 Conecte la alimentación (POWER) de la cámara digital.
5 Encienda la pantalla LCD.
6 Ponga todos los ajustes de la cámara digital en el modo
automático.
D Instalación de la cámara digital
1 Desconecte la alimentación (POWER).
2 Ponga el selector de modo de la cámara digital en MOVIE. (D-2)
3 Ponga el selector de modo del portacámara subacuático en
MOVIE. (D-3)
4 Suelte la hebilla.
Abra el cuerpo lateral deslizando la palanca de bloqueo (1) y soltando la hebilla
en los sentidos de las flechas 2, 3. (D-4-1)
La parte de goma negra es un espaciador. Guarde el espaciador porque lo
necesitará para guardar el portacámara subacuático.
5 Prepare el portacámara subacuático.
1
Recubra la junta tórica con grasa.
Limpie cualquier resto de arena o otros residuos que pueda haber en la junta
tórica, en la ranura de asiento, o en el cuerpo principal donde éste hace contacto
con la junta tórica. Recubra la junta tórica con una capa de grasa liguera y
uniforme.
Si se cierra la cubierta con arena u otros residuos adheridos a estos lugares, se
podrá dañar el cuerpo principal o se podrá fugar agua al interior del
portacámara subacuático.
2
Recubra el cristal frontal con líquido antiempañante para objetivos.
Recubra la superficie del cristal de la parte delantera del portacámara
subacuático con el líquido antiempañante para objetivos suministrado.
6 Instale la cámara digital.
Compruebe que el objetivo y la pantalla LCD estén limpios antes de instalar la
cámara digital.
7 Cierre el cuerpo lateral.
Fije el cuerpo lateral, y abroche la hebilla hasta que se oiga un chasquido.
Precaución
Cuando cierre el cuerpo del portacámara subacuático, asegúrese de que no haya
residuos, arena, cabellos, ni ninguna otra materia extraña en la junta tórica o en la
ranura de asiento. Si hay alguna de tales materias extrañas en estos lugares podrá
producirse una fuga de agua.
Correa para el cuello E
Instale la correa para el cuello suministrada antes de utilizar el portacámara
subacuático.
Utilización del portacámara
subacuático
F Grabación
1 Conecte la alimentación.
Compruebe que el selector de modo funciona normalmente.
2 Ponga el selector de modo en el modo deseado y pulse el
disparador.
Podrá sacar fotografías mientras mira a la pantalla LCD o a través del visor.
Para grabar imágenes fijas, póngalo en STILL.
Para grabar imágenes en movimiento, póngalo en MOVIE. (Durante la grabación
de imágenes en movimiento no se puede grabar el sonido.)
Para más detalles, consulte el manual de instrucciones suministrado con la cámara
digital.
Utilización de las distintas funciones G
Puede utilizar las distintas funciones de la cámara digital instalada en el
portacámara subacuático.
1
Utilización del flash
2
Grabación de imágenes en macro
3
Fijación de los distintos ajustes
Utilización del zoom H
Pulse el botón del zoom.
Cuando utilice el visor para grabar, el botón del zoom se producirá eclipse
en la imagen del visualizador, pero no repercutirá en la imagen grabada.
1
Pulse el lado W para gran angular. (El motivo aparecerá más alejado.)
2
Pulse el lado T para telefoto. (El motivo aparecerá más cerca.)
Precaución
Si no utiliza ninguna operación de la cámara por más de tres minutos
durante la grabación, ésta se apagará automáticamente para evitar que se
descargue la batería. Para volver a utilizar la cámara, deslice el interruptor
POWER a la posición activada.
I Reproducción con el botón de control
Puede reproducir imágenes en la pantalla LCD utilizando el botón de
control. No podrá oír el sonido.
1 Conecte la alimentación (POWER).
2 Ponga el selector de modo en PLAY.
3 Seleccione la imagen deseada con el botón de control.
Para más detalles, consulte el manual de instrucciones suministrado con la cámara
digital.
J Extracción de la cámara digital
1 Desconecte la alimentación (POWER).
Asegúrese siempre de desactivar el interruptor POWER cuando
instale o extraiga la cámara digital. Si está conectada la
alimentación podrá dañarse el objetivo.
2 Ponga el selector de modo del portacámara subacuático en
MOVIE.
3 Suelte la palanca de bloqueo y abra el portacámara subacuático.
4 Extraiga la cámara digital DSC-P1.
Tenga cuidado de no dejar caer la cámara digital cuando la
extraiga.
Precaución
Antes de abrir el portacámara subacuático, aclárelo con agua del grifo o con
agua dulce y luego frótelo con un paño suave y seco. Cuando lo abra, tenga
cuidado de no dejar que chorree agua de su cuerpo, cabello, o traje de agua
en la cámara digital.
Antes de bucear
·Antes de grabar imágenes bajo el agua, sumerja primero el portacámara
subacuático a una profundidad de aproximadamente 1 metro y
compruebe que funciona debidamente y que no haya fugas, y a
continuación comience su buceo.
·Instale la cámara digital en el portacámara subacuático antes de bucear, y
evite en la medida de lo posible abrirlo y cerrarlo mientras esté embarcado
o en la costa. Cuando instale la cámara digital, hágalo en un lugar que
tenga la menor humedad posible.
·Antes de utilizar el portacámara subacuático, asegúrese de que no haya
residuos pillados entre las mitades delantera y trasera del cuerpo.
Horas apropiadas para grabar
La hora más apropiada para grabar imágenes es entre las 10:00 de la
mañana y las 2:00 de la tarde, cuando el sol se encuentra directamente
encima.
Para grabar imágenes en lugares donde la luz solar no llegue bien o durante
la noche, utilice la lámpara para vídeo subacuática HVL-ML20 (no
suministrada).
Nota
En las imágenes grabadas bajo el agua, algunas veces el motivo tendrá un
tono azulado. Para corregir el color cuando ocurra esto, utilice el juego de
filtros VF-MP1K, que está disponible como accesorio opcional.
Solución de problemas
Síntoma
Hay gotas de agua dentro del
portacámara subacuático.
Las funciones de grabación y
reproducción no responden.
Causa/acciones correctivas
· Las hebillas no están abrochadas.
b Abroche las hebillas hasta que produzcan
un chasquido.
· La junta tórica no está puesta correctamente.
b Ponga la junta tórica uniformemente en la
ranura.
· Hay raspaduras o grietas en la junta tórica.
b Sustituya la junta tórica con otra nueva.
· La batería se ha agotado.
b Cargue completamente la batería.
· El "Memory Stick" está lleno.
b Inserte otro "Memory Stick" o borre datos
que no necesite del "Memory Stick".
· La lengüeta de protección contra el borrado
del "Memory Stick" está puesta en LOCK.
b Ponga la lengüeta en la posición de
grabación o inserte un "Memory Stick"
nuevo.
Especificaciones
Material
Plástico (PC, ABS), acero inoxidable, cristal
Estanqueidad
Junta tórica, hebilla
Resistencia a la presión
Hasta una profundidad de 30 metros bajo el agua
Interruptores que se pueden accionar externamente
Alimentación, modo, disparador, zoom, flash, macro, control
Dimensiones
Aprox. 150
× 80 × 86 mm (An/Al/Prf)
Peso
Aprox. 300 g (portacámara subacuático solamente)
Accesorios suministrados
Correa para el cuello (1)
Grasa (1)
Líquido antiempañante para objetivos (1)
Manual de instrucciones (1)
Accesorios opcionales
Juego de filtros VF-MP1K
Brazo acoplable VCT-MP1K
lámpara para vídeo subacuática HVL-ML20 (ha de utilizarse junto con el
brazo acoplable VCT-MP1K, la batería "InfoLITHIUM" (serie L) y el cargador
de batería serie L)
El diseño y las especificaciones están sujetos a cambio sin previo aviso.
Disparador
Sluiterknop
Selector de modo
Moduskeuzeschakelaar
Interruptor de
alimentación
Spannings-
schakelaar
Cristal frontal
Glas aan
voorkant
Hebilla
Gesp
Espaciador (quítelo para usar el
portacámara subacuático)
Afstandsstuk (verwijderen voor
gebruik van onderwaterbehuizing)
Palanca de bloqueo
Grendelhefboom
Gancho para la
correa para el cuello
Haak voor halsriem
Receptáculo
para trípode
Schroefgang
voor statief
Botones del
zoom
Zoomknoppen
Botones de
control
Regelknoppen
Botón
(flash)
Flitserknop (
)
Botón
(MACRO)
Macroknop (
)
Montura del juego
de filtros
Filtersetmontage
Nederlands
Belangrijkste kenmerk
Te gebruiken tot op een diepte van maar liefst 30 meter onder water
Deze onderwaterbehuizing MPK-P1 is uitsluitend bestemd voor gebruik
met de digitale stilbeeldcamera DSC-P1 van Sony. Aangezien deze
onderwaterbehuizing waterbestendig is, kan de digitale stilbeeldcamera
hiermee ook worden gebruikt in de regen, in de sneeuw of op het strand.
Nadere aanwijzingen over het gebruik van uw digitale stilbeeldcamera met
deze behuizing vindt u in de gebruiksaanwijzing van de digitale
stilbeeldcamera.
Opmerking
·Alvorens u de digitale stilbeeldcamera onder water gaat gebruiken, dient
u de onderwaterbehuizing eerst tot op een diepte van circa 1 meter te
brengen en te controleren of de digitale stilbeeldcamera naar behoren
werkt en de onderwaterbehuizing niet lekt. Daarna kunt u beginnen met
duiken.
·Indien er door een defect van de onderwaterbehuizing als gevolg van
waterlekkage schade ontstaat, hetgeen overigens zeer onwaarschijnlijk is,
aanvaardt Sony geen aansprakelijkheid voor eventuele beschadiging van
de daarin aanwezige apparatuur (digitale stilbeeldcamera, batterij, enz.)
en de gemaakte opnamen, en evenmin voor de kosten die verbonden zijn
aan het fotograferen.
Voorzorgsmaatregelen
·Stel het glas aan de voorkant niet bloot aan krachtige schokken, aangezien
het hierdoor kan gaan barsten.
·Open de onderwaterbehuizing niet op het strand of op het water. De
voorbereidingen, zoals het installeren van de digitale stilbeeldcamera en
het verwisselen van de "Memory Stick", dienen te geschieden op een
plaats met een lage vochtigheid en zonder zoute lucht.
·Gooi de onderwaterbehuizing niet in het water.
·Gebruik de onderwaterbehuizing niet op plaatsen met een sterke golfslag.
·Gebruik de onderwaterbehuizing niet onder de volgende
omstandigheden:
­ op een zeer warme of vochtige plaats
­ in water met een temperatuur boven 40°C
­ bij temperaturen beneden 0°C
Onder bovengenoemde omstandigheden kan er condensvorming of
waterlekkage optreden waardoor de apparatuur beschadigd kan raken.
·Bij temperaturen boven 35°C mag u de onderwaterbehuizing niet langer
dan 30 minuten aaneen gebruiken.
·Laat de onderwaterbehuizing niet achter op een zeer warme en vochtige
plaats waar deze langdurig is blootgesteld aan direct zonlicht. Indien u de
onderwaterbehuizing beslist moet achterlaten op een plaats met direct
zonlicht, dient u de behuizing altijd te bedekken met een handdoek of
andere bescherming.
Waterlekkage
Indien er toevallig water naar binnen is gelekt, zorg dan onmiddellijk dat
de onderwaterbehuizing niet langer aan water wordt blootgesteld.
Indien de digitale stilbeeldcamera nat is geworden, dient u deze
onmiddellijk naar de dichtstbijzijnde Sony-handelaar te brengen.
Lensvloeistof
Breng op het glasoppervlak een laagje lensvloeistof aan. Deze bijgeleverde
lensvloeistof is een doeltreffend middel om te voorkomen dat de lens
beslaat.
Gebruiksaanwijzing voor de lensvloeistof
Breng één of twee druppeltjes lensvloeistof aan op de binnenkant van het
glas aan de voorkant en op het glas van het oculair, en wrijf de vloeistof
gelijkmatig uit over het glasoppervlak door gebruikmaking van een
wattenstaafje, een zachte doek of tissuepapier.
O-ring A
Deze apparatuur is voorzien van een O-ring om de waterbestendigheid te
handhaven. Neem de volgende punten in acht om de functie van de O-ring
volledig te benutten.
Een onjuiste behandeling van de O-ring kan waterlekkage tot gevolg
hebben.
Onderhoud van de O-ring
Indien de O-ring beschadigd of gescheurd is, kan er water in de
onderwaterbehuizing gaan lekken. Elke keer wanneer u de
onderwaterbehuizing gebruikt, dient u de O-ring derhalve aan de
buitenkant te controleren om ervan verzekerd te zijn dat deze niet
beschadigd is en dat er zich geen stof of vuil aan heeft vastgehecht.
·Verwijder de O-ring met uw vingers. Gebruik hiervoor geen puntige of
metalen voorwerpen, aangezien deze de zittinggroef op de
onderwaterbehuizing kunnen beschadigen.
·Zorg dat de O-ring niet gedraaid is wanneer u deze vastmaakt.
·Zorg dat de O-ring altijd is bedekt met een dun laagje vet. Het vet
beschermt de O-ring en voorkomt slijtage.
·Smeer het vet gelijkmatig uit met uw vinger, of leg de O-ring en een kleine
hoeveelheid vet in een plastic zak en kneed deze voorzichtig met beide
handen. Gebruik hiervoor geen papier of doek, aangezien er zich dan
vezels aan de O-ring kunnen vasthechten.
Vet (nr. 2-115-921-01) is verkrijgbaar bij uw Sony-handelaar.
Sluiten van de onderwaterbehuizing
Zorg dat de O-ring niet uit de zittinggroef is gegleden. Wanneer de O-ring
ergens tussen bekneld is geraakt, wordt deze niet alleen beschadigd, maar
kan hierdoor ook water in de onderwaterbehuizing lekken.
Gebruiksduur van O-ringen
De gebruiksduur van een O-ring is afhankelijk van de gebruiksfrequentie
van de onderwaterbehuizing en de omstandigheden waaronder deze wordt
bewaard, maar over het algemeen gaat een O-ring ongeveer één jaar mee.
O-ringen (nr. 3-065-033-01) zijn verkrijgbaar bij uw Sony-handelaar.
Opbergen van O-ringen
Bewaar extra O-ringen niet meegeleverd op een koele plaats waar ze niet
aan direct zonlicht zijn blootgesteld. Buig ze niet en plaats er geen zware
voorwerpen op.
Controle op waterlekkage na vervanging van de O-ring
Alvorens u de digitale stilbeeldcamera installeert, dient u de
onderwaterbehuizing te controleren op waterlekkage.
Sluit de onderwaterbehuizing zonder de digitale stilbeeldcamera te
installeren. Houd de onderwaterbehuizing gedurende circa 3 minuten
onder water op een diepte van circa 15 cm en controleer vervolgens op
waterlekkage.
Onderhoud
Na het opnemen
·Na het maken van opnamen op een plaats met harde zeewind dient u de
onderwaterbehuizing ­ met de gespen stevig vast ­ met zoet water te
wassen om zout en zand te verwijderen. Veeg na met een zachte droge
doek. Het is aan te bevelen om de onderwaterbehuizing gedurende circa
30 minuten ondergedompeld te houden in zoet water. Indien er zout op
blijft zitten, bestaat de kans dat de metalen onderdelen beschadigd raken
of gaan roesten n en waterlekkage veroorzaken.
·Indien er zonnebrandolie of andere vettige stoffen op de
onderwaterbehuizing terecht zijn gekomen, dient u deze er met lauw
water af te wassen.
·Reinig de binnenkant van de behuizing met een zachte droge doek. De
binnenkant van de behuizing mag niet worden gewassen. Elke keer
wanneer u de onderwaterbehuizing hebt gebruikt, dient u altijd het
bovenstaande onderhoud te verrichten. Gebruik voor het reinigen geen
oplosmiddelen zoals alcohol, benzine of verdunner aangezien deze de
afwerklaag kunnen beschadigen.
Opbergen van de onderwaterbehuizing
·Bevestig het met de onderwaterbehuizing meegeleverde afstandsstuk om
slijtage van de O-ring te voorkomen. (Zie afbeelding B.)
·Zorg dat er zich geen stof op de O-ring kan ophopen.
·Breng een dun laagje vet aan op de O-ring en plaats deze in de
zittinggroef. Berg de onderwaterbehuizing vervolgens op een koele, goed
geventileerde plaats op. Maak de gesp niet vast.
·De onderwaterbehuizing mag niet worden opgeborgen op een koude of
zeer warme of vochtige plaats, en ook niet samen met naftaleen of kamfer,
aangezien de behuizing hierdoor beschadigd kan raken.
Voorbereiding
Voorbereiden van de digitale stilbeeldcamera
Nadere bijzonderheden vindt u in de gebruiksaanwijzing die met uw
digitale stilbeeldcamera DSC-P1 is meegeleverd.
1 Verwijder de polsband van de digitale stilbeeldcamera DSC-P1.
2 Installeer de batterij.
Zorg dat u altijd gebruikmaakt van een volledig opgeladen batterij.
3 Plaats de "Memory Stick".
4 Schakel de spanning (POWER) van de digitale stilbeeldcamera
in.
5 Schakel het LCD-scherm in.
6 Zet alle instellingen van de digitale stilbeeldcamera in de
automatische modus.
D Installeren van de digitale stilbeeldcamera
1 Schakel de spanning (POWER) uit.
2 Zet de moduskeuzeschakelaar van de digitale stilbeeldcamera
op MOVIE. (D-2)
3 Zet de moduskeuzeschakelaar van de onderwaterbehuizing op
MOVIE. (D-3)
4 Maak de gesp los.
Open het zijblok door de grendelhefboom (1) te schuiven en de gesp los te maken,
in de richting van de pijltjes 2 en 3. (D-4-1)
Het zwarte rubberen onderdeel is een afstandsstuk. Bewaar het afstandsstuk,
aangezien u dit nodig zult hebben voor het opbergen van de onderwaterbehuizing.
5 Tref de nodige voorbereidingen voor de onderwaterbehuizing.
1
Breng een laagje vet aan op de O-ring.
Verwijder alle zand en ander vuil dat eventueel nog aanwezig is op de O-ring,
in de zittinggroef of op de onderwaterbehuizing waar deze in aanraking komt
met de O-ring. Breng een dun gelijkmatig laagje vet aan op de O-ring.
Indien het deksel wordt gesloten terwijl er op de genoemde plaatsen nog zand
of ander vuil zit vastgehecht, bestaat de kans dat de onderwaterbehuizing
beschadigd raakt en dat er water in kan gaan lekken.
2
Breng een laagje lensvloeistof aan op het glas aan de voorkant.
Breng op het glas aan de voorkant van de onderwaterbehuizing een laagje van
de bijgeleverde lensvloeistof aan om te voorkomen dat de lens beslaat.
6 Installeer de digitale stilbeeldcamera.
Alvorens u de digitale stilbeeldcamera installeert, dient u te controleren of de lens
en het LCD-scherm goed schoon zijn.
7 Sluit het zijblok.
Zet het zijblok vast en maak de gesp vast totdat deze klikt.
Let op
Bij het sluiten van de onderwaterbehuizing dient u ervan verzekerd te zijn dat er
op de O-ring en in de zittinggroef geen vuil, zand, haren of andere voorwerpen
meer aanwezig zijn die daar niet thuishoren. Indien dergelijke voorwerpen op de
genoemde plaatsen blijven zitten, kan er waterlekkage optreden.
Halsriem E
Alvorens u de onderwaterbehuizing gaat gebruiken, dient u de bijgeleverde
halsriem vast te maken.
Gebruik van de onderwaterbehuizing
F Opnemen
1 Schakel de spanning (POWER) in.
Controleer of de moduskeuzeschakelaar normaal functioneert.
2 Zet de moduskeuzeschakelaar in de gewenste stand en druk op
de sluiterknop.
U kunt opnamen maken terwijl u naar het LCD-scherm of door de zoeker kijkt.
Om stilstaande beelden op te nemen, kiest u STILL.
Om bewegende beelden op te nemen, kiest u MOVIE. (Tijdens het opnemen van
bewegende beelden kunt u geen geluid opnemen.)
Nadere bijzonderheden vindt u in de gebruiksaanwijzing die met uw digitale
stilbeeldcamera is meegeleverd.
Gebruik van verschillende functies G
Ook wanneer de digitale stilbeeldcamera in de onderwaterbehuizing is
geplaatst, kunt u verschillende functies van de camera blijven gebruiken.
Zo kunt u:
1
de flitser gebruiken
2
beelden in macro opnemen
3
verschillende instellingen maken
Gebruik van de zoom H
Druk op de zoomknop.
Wanneer u bij het opnemen gebruikmaakt van de zoeker, zal het
onderwerp tijdelijk uit de zoeker verdwÿnen, maar dit heeft geen effect op
het opgenomen beeld.
1
Druk op de W-kant voor groothoek-opnamen (onderwerp lijkt verder
weg)
2
Druk op de T-kant voor tele-opnamen (onderwerp lijkt dichterbij)
Let op
Indien u de camera tijdens het opnemen gedurende een periode van langer
dan drie minuten niet bedient, zal deze automatisch uitschakelen om te
voorkomen dat de batterij uitgeput raakt. Om de camera opnieuw te
gebruiken, verschuift u de POWER-schakelaar naar "ON" (aan).
I Weergave met de regelknop
U kunt beelden weergeven op het LCD-scherm door gebruikmaking van de
regelknop. Er is dan echter geen geluid te horen.
1 Schakel de spanning (POWER) in.
2 Zet de moduskeuzeschakelaar op PLAY.
3 Kies met de regelknop het gewenste beeld.
Nadere bijzonderheden vindt u in de gebruiksaanwijzing die met uw digitale
stilbeeldcamera is meegeleverd.
J Verwijderen van de digitale stilbeeldcamera
1 Schakel de spanning (POWER) uit.
Schakel altijd de spanning (POWER) uit alvorens u de digitale
stilbeeldcamera gaat installeren of verwijderen. Indien de
spanning is ingeschakeld, kan de lens beschadigd raken.
2 Zet de moduskeuzeschakelaar van de onderwaterbehuizing op
MOVIE.
3 Maak de grendelhefboom los en open de onderwaterbehuizing.
4 Verwijder de digitale stilbeeldcamera DSC-P1.
Pas op dat u de digitale stilbeeldcamera niet laat vallen wanneer
u deze verwijdert.
Let op
Alvorens u de onderwaterbehuizing opent, dient u deze af te spoelen met
leidingwater of zoet water. Veeg het water er vervolgens af met een zachte
doek. Wanneer u de onderwaterbehuizing opent, dient u erop te letten dat
er geen waterdruppels van uw lichaam, haar of duikpak op de digitale
stilbeeldcamera terechtkomen.
Alvorens u gaat duiken
·Alvorens u beelden onder water gaat opnemen, dient u de
onderwaterbehuizing eerst tot op een diepte van circa 1 meter te brengen
en te controleren of deze niet lekt. Daarna kunt u beginnen met duiken.
·Installeer de digitale stilbeeldcamera in de onderwaterbehuizing alvorens
u gaat duiken. Probeer de onderwaterbehuizing aan zee en aan boord van
vaartuigen zo weinig mogelijk te openen en te sluiten. Installeer de
digitale stilbeeldcamera op een plaats met een zo laag mogelijke
vochtigheid.
·Alvorens u de onderwaterbehuizing gaat gebruiken, dient u zich ervan te
verzekeren dat er tussen de voorste en achterste helft van de behuizing
geen vuil meer zit.
Geschikte tijden voor opnemen
De beste tijd voor het maken van opnamen is overdag tussen 10.00 uur en
14.00 uur wanneer de zon recht boven u staat.
Wanneer u opneemt op plaatsen waar het zonlicht moeilijk kan
binnendringen of wanneer u in het donker opneemt, gebruik dan de
onderwatervideolamp HVL-ML20 (niet bijgeleverd).
Opmerking
Bij opnamen die onder water zijn gemaakt, ziet het onderwerp er soms
enigszins blauwachtig uit. Om in een dergelijk geval de kleur te corrigeren,
dient u gebruik te maken van de filterset VF-MP1K die als losse accessoire
verkrijgbaar is.
Verhelpen van storingen
Symptoom
Er zitten druppeltjes water
binnen in de
onderwaterbehuizing.
De functie voor opname en
weergave werkt niet.
Oorzaak en/of oplossing
· De gespen zijn niet vastgemaakt.
b Maak de gespen vast totdat deze klikken.
· De O-ring is niet correct aangebracht.
b Plaats de O-ring gelijkmatig in de groef.
· De O-ring is gekrast of gescheurd.
b Vervang de O-ring door een nieuw
exemplaar.
· De batterij is leeg.
b Laad de batterij volledig op.
· De "Memory Stick" is vol.
b Plaats een andere "Memory Stick" of wis
overbodige gegevens uit de "Memory
Stick".
· Het schrijfbeveiligingsnokje op de "Memory
Stick" staat op LOCK.
b Breng het nokje in de opnamestand of
plaats een nieuwe "Memory Stick".
Specificaties
Materiaal
Kunststof (PC, ABS), roestvrij staal, glas
Waterbestendigheid
O-ring, gesp
Drukbestendigheid
Tot op een diepte van 30 m onder water
Regelaars die vanaf de buitenkant bediend kunnen worden
Spanningsschakelaar, moduskeuzeschakelaar, sluiterknop, zoomknop,
flitserknop, macroknop, regelknop
Afmetingen
Circa 150
× 80 × 86 mm (b/h/d)
Gewicht
Circa 300 g (alleen onderwaterbehuizing)
Bijgeleverde accessoires
Halsriem (1)
Vet (1)
Lensvloeistof (1)
Gebruiksaanwijzing (1)
Los verkrijgbare accessoires
Filterset VF-MP1K
Armset VCT-MP1K
Onderwatervideolamp HVL-ML20 (dient te worden gebruikt met armset
VCT-MP1K, "InfoLITHIUM" batterij (serie L) en batterijlader serie L)
Wijzigingen in ontwerp en technische gegevens voorbehouden zonder
voorafgaande kennisgeving.