background image
REVISION HISTORY BG3R
MODEL
KV-AR34M36
KV-AR34M60
KV-AR34M64
KV-AR34M64
KV-AR34M66
KV-AR34M94
PART NO. :
9-872-322-01
NO.
SUFFIX
DATE
SUPPL. / CORR
DESCRIPTION
CHASSIS
1
-01
2002/07
--
1st. Issue


background image
MODEL
COMMANDER DEST. CHASSIS NO.
CHASSIS
TRINITRON ® COLOR TV
SERVICE MANUAL
BG3R
MODEL
COMMANDER DEST.
CHASSIS NO.
KV-AR34M36 RM-993 Oceania
SCC-U44F-A
KV-AR34M60 RM-995 Thailand
SCC-U49M-A
KV-AR34M64 RM-993 India
SCC-U60K-A
KV-AR34M64 RM-993 Thailand
SCC-U49L-A
KV-AR34M66 RM-993 GE
SCC-U52H-A
KV-AR34M94 RM-993 India
SCC-U60K-A
RM-993
RM-995


background image
­ 2 ­
KV-AR34M36/AR34M64/AR34M66/AR34M94
RM-993
KV-AR34M60
RM-995
Power requirements
220-240 V AC, 50/60 Hz
KV-AR34M36/AR34M60/
AR34M64 (THAILAND)
110-240 V AC, 50/60 Hz
KV-AR34M64 (INDIA)/
AR34M66/AR34M94
Power consumption (W)
Indicated on the rear of the TV
Television system
B/G, I, D/K, M
Color system
PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
Stereo/Bilingual System NICAM Stereo/ Bilingual B/G, I;A2 Stereo/ Bilingual B/G
Teletext language
English, Arabic, French
KV-AR34M36/AR34M66 Only
Channel coverage
B/G
VHF: E2 to E12 / UHF: E21 to E69
CATV: S01 to S03, S1 to S41
I
UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K
VHF: C1 to C12, R1 to R12 /
UHF: C13 to C57, R21 to R60 /
CATV: S01 to S03, S1 to S41, Z1 to Z39
M
VHF: A2 to A13 / UHF: A14 to A79
CATV: A-8 to A-2, A to W+4, W+6 to W+84
(Antenna)
75-ohm external terminal
Audio output (Speaker)
8W + 8W
Number of terminal
DVideo
Input: 4*
Output: 1
* Three input lines available
Phono jacks; 1 Vp-p, 75 ohms
Audio
Input: 4*
Output: 1
* Three input lines available
Phono jacks; 500 mVrms
(S Video)
Input : 2
Y: 1 Vp-p, 75 ohms
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
(Component
Input : 1
Phono jacks:
Video)
Y: 1 Vp-p, 75 ohms
sync negative
CB: 0.7 Vp-p, 75 ohms
CR: 0.7 Vp-p, 75 ohms
Audio: 500mVrms
2 (Headphone)
Output: 1
Stereo minijack
Picture tube
34
Tube size (cm)
86
Measured diagonally
Screen size (cm)
80
Measured diagonally
Dimension (w/h/d,mm)
896
× 686 × 569
Mass (kg)
78
Design and specifications are subject to change without notice.
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.
Note


background image
­ 3 ­
KV-AR34M36/AR34M64/AR34M66/AR34M94
RM-993
KV-AR34M60
RM-995
TABLE OF CONTENTS
SELF DIAGNOSTIC FUNCTION ........................................ 4
1. DISASSEMBLY
1-1.
Rear Cover Removal ................................................... 7
1-2.
Speaker Removal ........................................................ 7
1-3.
Chassis Assy Removal ................................................ 7
1-4.
F Board Removal ........................................................ 7
1-5.
Service Position .......................................................... 7
1-6
HV Cap Block, PWB Holder and
DH Board Removal .................................................... 7
1-7.
Terminal Bracket and J Board Removal .................... 8
1-8.
D2 Board Removal ..................................................... 8
1-9.
H1 and H2 Boards Removal ....................................... 8
1-10. P5 Board Removal ...................................................... 8
1-11. B1 Board Removal ...................................................... 9
1-12. V1 Board Removal ..................................................... 9
1-13. A and B8 Boards Removal ......................................... 9
1-14. A and B10 Boards Removal ....................................... 9
1-15. Picture Tube Removal ............................................... 10
2. ADVANCE OPERATION
2-1.
"RESET" Function .................................................... 11
3. SET-UP ADJUSTMENTS
3-1.
Beam Landing ........................................................... 12
3-2.
Convergence .............................................................. 13
3-3.
Focus Adjustment ..................................................... 15
3-4.
G2 (SCREEN) and White Balance Adjustment ....... 16
4. CIRCUIT ADJUSTMENTS
4-1.
Adjustment With Commander .................................. 17
4-2.
Adjustment Method .................................................. 17
4-3.
Adjustment for Non Digital Texture Enhancer (DTE)
Model (KV-AR34M60 only) .................................... 40
4-4.
Adjustment for Digital Texture Enhancer (DTE)
Model (except KV-AR34M60) ................................. 40
4-5.
Display Position Adjustment .................................... 41
4-6.
Deflection Adjustment .............................................. 41
4-7.
H-Trapezoid Adjustment .......................................... 42
4-8.
A Board Adjustment After IC003 (MEMORY)
Replacement .............................................................. 42
4-9.
Picture Distortion Adjustment .................................. 43
Section
Title
Page
Section
Title
Page
5. DIAGRAMS
5-1.
Block Diagram .......................................................... 44
5-2.
Circuit Board Location ............................................. 48
5-3.
Schematic Diagram ................................................... 49
(1) C6 and J Boards Schematic Diagrams ............... 50
(2) A Board Schematic Diagram .............................. 52
(3) B8 Board Schematic Diagram ............................ 56
(4) P5 Board Schematic Diagram ............................. 58
(5) D2 Board Schematic Diagram ............................ 66
(6) H1 and F Boards Schematic Diagrams ............... 68
(7) B10 Board Schematic Diagram .......................... 70
(8) V1 Board Schematic Diagram ............................ 72
(9) B1 Board Schematic Diagram ............................ 74
(10) DH Board Schematic Diagram ......................... 75
(11) H2 Board Schematic Diagram .......................... 76
(12) VM1 Board Schematic Diagram ...................... 77
5-4.
Voltage List and Waveforms ..................................... 82
5-5.
Printed Wiring Boards and Parts Location ............... 91
5-6.
Semiconductors ....................................................... 107
6. EXPLODED VIEWS
6-1.
Speaker Bracket ...................................................... 109
6-2.
Chassis .................................................................... 110
6-3.
Picture Tube ............................................................ 112
7. ELECTRICAL PARTS LIST ....................................... 114
OPERATING MANUAL


background image
­ 4 ­
KV-AR34M36/AR34M64/AR34M66/AR34M94
RM-993
KV-AR34M60
RM-995
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user's knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1.
DIAGNOSTIC TEST INDICATORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a "0".
Diagnostic
Item
Description
· Power does not
turn on
· +B overcurrent
(OCP) or
overvoltage
(OVP)
· Vertical deflection
stopped
· Horizontal
deflection
overdrive
· White balance
failure (no
PICTURE)
· Micro reset
Detected
Symptoms
· Power does not come on.
· No power is supplied to the
TV.
· AC power supply is faulty.
· Power does not come on.
· Load on power line is
shorted.
· Has entered standby state
after horizontal raster.
· Vertical deflection pulse is
stopped.
· Power line is shorted or
power supply is stopped.
· No raster is generated.
· CRT cathode current
detection reference pulse
output is small.
· Power is shut down shortly,
after this return back to
normal.
· Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
* R(Q703), G(Q702) or B(Q701) out is faulty (C6 board).
SELF DIAGNOSTIC FUNCTION
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
--
Self-diagnostic
display/Diagnostic
result
--
002:000 or
002:001~255
003:001~255
004:001~255
at the same time
005:000 or
005:001~225
101:00 or
101:001~225
Probable
Cause
Location
· Power cord is not plugged
in.
· Fuse is burned out F4601
(F)
· H.OUT Q511 is shorted.
(A board)
· Q701, Q702, Q703 is
shorted (C6 board)
· -13V is not supplied.
(A board)
· IC 503 faulty (A board)
· G2 is improperly adjusted.
(Note 2)
· CRT problem.
· R(Q703), G(Q702) or
B(Q701) out is faulty
(C6 board)
· IC301 is faulty. (A board)
· No connection A board to
C6 board.
· Discharge CRT (C6 Board)
· Static discharge
· External noise