background image
HISTORY
When clicking an item, it's detail is displayed.
Date
SUPP./CORR.
Description of SUP/COR
Change of
main text
2005.8
­
NEW
­
Model Name : KDS-R50XBR1/R60XBR1
SERVICE MANUAL
Part No.
: 9-872-762-01


background image
SERVICE MANUAL
MODEL
COMMANDER
DEST. CHASSIS NO.
­­­­­­
­­­­­­­­­­­­ ­­­­­ ­­­­­­­­­­­
MODEL
COMMANDER
DEST. CHASSIS NO.
­­­­­­
­­­­­­­­­­­­ ­­­­­ ­­­­­­­­­­­
CHASSIS
KDS-R50XBR1 RM-Y914
USA
KDS-R50XBR1 RM-Y914
CANADA
KDS-R50XBR1 RM-Y914
MEXICO
KDS-R60XBR1 RM-Y914
USA
KDS-R60XBR1 RM-Y914
CANADA
KDS-R60XBR1 RM-Y914
MEXICO
SXRD PROJECTION TV
RM-Y914
KDS-R50XBR1/R60XBR1
SP-1


background image
­ 2 ­
KDS-R50XBR1/R60XBR1
RM-Y914
RM-Y914
Specifications
Projection System
3 SXRD Panel, 1 lens projection system
SXRD Panel
0.61 inch SXRD panel 6,220,800 pixels (2,073,600
× 3)
Projection Lens
High Performance, large diameter hybrid lens F2.5
Antenna
75 ohm external terminal for VHF/UHF
Lamp
UHP lamp, 120W, XL-5100
Television System
NTSC
American TV Standard
ATSC (8VSB terrestrial)
ATSC compliant 8VSB
QAM on cable
ANSI/SCTE 07 2000
Visible Screen Size
(picture measured diagonally)
KDS-R50XBR1: 50 inches
KDS-R60XBR1: 60 inches
Channel Coverage
Terrestrial (analog)
2-69
Cable TV (analog)
1-125
Terrestrial (digital)
2-69
Cable TV (digital)
1-135
Power Requirements
120V, 60 Hz
Inputs/Outputs
HDMI IN
2 total
Video: 1080i, 720p, 480p, 480i
Audio: Two channel linear PCM 32, 44.1 and
48 kHz, 16, 20 and 24 bit
Video (IN)
3 total (1 on front panel)
1 Vp-p, 75 ohms unbalanced, sync negative
S Video (IN)
3 total (1 on front panel)
Y: 1 Vp-p, 75 ohms unbalanced, sync
negative
C: 0.286 Vp-p (Burst signal), 75 ohms
Audio (IN)
6 total (1 on front panel)
500 mVrms (100% modulation)
Impedance: 47 kilohms
Component Video Input
2 (YPBPR)
Y: 1 Vp-p, 75 ohms unbalanced, sync
negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
CONTROL S (IN)
1
Mini jack
CONTROL S (OUT)
1
Mini jack
AUDIO OUT (VAR/FIX)
1
500 mVrms at the maximum volume setting
(Variable)
500 mVrms (Fixed)
Impedance (output): 2 kilohms


background image
­ 3 ­
KDS-R50XBR1/R60XBR1
RM-Y914
RM-Y914
Other Information
Design and specifications are subject to change without notice.
PC IN
D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive
i.LINK
3 total (1 on front panel)
4-pin S400 i.LINK terminal
RF Inputs
2
Digital Audio Optical Output
(PCM/Dolby Digital)
1Optical Rectangular (1)
CableCARD Slot
PCMCIA Type I/II
Speaker Output
15 W (L), 15 W (R)
Dimensions (W H D)
KDS-R50XBR1 1,453
× 863 × 47 8 mm (57 1/4 × 34 × 18 7/8 inches)
KDS-R60XBR1 1,674
× 1,009 × 514 mm (66 × 39 3/4 × 20 1/4 inches)
Mass
KDS-R50XBR1 43kg (94 lb. 13 oz.)
KDS-R60XBR1 51kg (112 lb. 7 oz.)
Power Consumption
In Use
240 W
In Standby
0.5 W
In i.LINK/CableCARD Standby
Less than 30 W
Supplied Accessories
Remote Control
RM-Y914
AA (R6) Batteries
2 supplied for remote control
Operating Instructions
1
Quick Setup Guide
1
Warranty
1
Product Registration Card
1


background image
­ 4 ­
KDS-R50XBR1/R60XBR1
RM-Y914
RM-Y914
Indicators
The indicators show the current status of your TV. If there is a change in the
condition or a problem with the TV, the indicators will flash or light up in
the manner described below to let you know that it requires your attention.
Projection Lamp
Your TV uses a projection lamp as its light source. As with any lamp, it has
limited life and needs to be replaced when the Lamp indicator flashes or the
screen becomes darker. Note the following:
After turning on your TV, it may take a while (1 minute or less) before
the picture appears.
When the projection lamp wears out, the screen goes dark. Replace the
lamp with a new Sony XL-5100 replacement lamp (not supplied).
Indicator
Flashing because...
POWER/
STANDBY
flashing
Green
The lamp for the light source is preparing to turn
on. When it is ready, it turns on.
Red
The lamp door or the lamp is not securely attached.
The red indicator will continue to flash in intervals
of three blinks at a time until the lamp door or the
lamp is placed correctly.
The red indicator is on when i.LINK STANDBY is
on or when your TV is in the PC power saving
mode.
LAMP indicator
flashes
The projection lamp has burned out. Replace it with new one
(see page 5 ).
TIMER indicator
is lit
When one of the timers is set the indicator will remain lit (will
not flash) even when the TV is turned off.
POWER/STANDBY
POWER
LAMP
TIMER
STD/DUO
Indicators
Screen
The light emitted from the lamp is quite bright when your TV i s in
use. To avoid eye discomfort or injury, do not look into the light
housing when the power is on.