SONY KDS-55A2000 - Service Manual Immediate Download

SERVICE MANUAL

MODEL

COMMANDER

DEST. CHASSIS NO.

MODEL

COMMANDER

DEST. CHASSIS NO.

CHASSIS

KDS-50A2000

RM-YD010

USA

KDS-50A2000

RM-YD010

CANADA

KDS-50A2010

RM-YD010

MEXICO

KDS-55A2000

RM-YD010

USA

KDS-55A2000

RM-YD010

CANADA

SXRD PROJECTION TV

OPEN

POWER

TIMER

LAMP

POWER

RM-YD010

KDS-50A2000/50A2010/55A2000/60A2000/60A2010

SP-3

KDS-60A2000

RM-YD010

USA

KDS-60A2000

RM-YD010

CANADA

KDS-60A2010

RM-YD010

MEXICO

KDS-50A2000/50A2010/55A2000/60A2000/60A2010

RM-YD010

Specifications

Television system:

NTSC

American TV Standard

ATSC (8VSB terrestrial) ATSC compliant 8VSB

QAM on cable

ANSI/SCTE 07 2000

(Does not include CableCARD

functionality)

Channel coverage:

Terrestrial (analog)

2-69

Cable TV (analog)

1-125

Terrestrial (digital)

2-69

Cable TV (digital)

1-135

Antenna:

75-ohm external terminal for VHF/UHF

Screen size (measured diagonally):

KDS-50A2000/KDS-50A2010: 50 inches

KDS-55A2000: 55 inches

KDS-60A2000/KDS-60A2010: 60 inches

Projection system

3 SXRD panel, 1 lens projection system

SXRD panel

0.61 inch SXRD panel 6,220,800 pixels (2,073,600

× 3)

Projection lens

High performance, large diameter hybrid lens F2.5

Lamp

Ultra High Pressure Lamp , 120W, XL-5200

VIDEO IN 1/2/3:

YPBPR

Y: 1.0 Vp-p, 75 ohms unbalanced,

sync negative

PB: 0.7 Vp-p, 75 ohms

PR: 0.7 Vp-p, 75 ohms

Signal format: 480i, 480p, 720p, 1080i

S VIDEO (4-pin mini DIN) (VIDEO 1 only):

Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative

C: 0.286 Vp-p (Burst signal), 75 ohms

VIDEO:

1 Vp-p, 75 ohms unbalanced, sync negative

AUDIO:

500 mVrms (100% modulation)

Impedance: 47 kilohms

HD/DVD IN 4/5:

YPBPR

Y: 1.0 Vp-p, 75 ohms unbalanced,

sync negative

PB: 0.7 Vp-p, 75 ohms

PR: 0.7 Vp-p, 75 ohms

Signal format: 480i, 480p, 720p, 1080i

AUDIO:

500 mVrms (100% modulation)

Impedance: 47 kilohms

HDMI IN 6/7:

HDMI:

Video: 480i, 480p, 720p, 1080i, 1080p

Audio: Two channel linear PCM 32, 44.1 and

48 kHz, 16, 20 and 24 bits

AUDIO (for HDMI IN 7):

500 mVrms (100% modulation)

Impedance: 47 kilohms

AUDIO OUT:

500 mVrms (100% modulation)

More than 1 Vrms at the maximum volume setting (Variable)

Optical Digital Audio Output (PCM/Dolby digital)

0 mVrms (Fixed)

PC IN 8:

DIGITAL OUT(OPTIVAL):

D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive

See the PC Input Signal Reference Chart on page 61

PC AUDIO INPUT:

Stereo mini jack, 0.5 Vrms, 47 kilohm

Speaker:

Full range: 70

× 130 mm (2

× 5

inches) (2)

Speaker output:

12 W + 12 W

Power requirement:

120 V AC, 60 Hz

Power consumption:

In use: 210W

In standby: Less than 0.5W

Dimensions (W/H/D):

KDS-50A2000/KDS-50A2010: 1180

× 839 × 447 mm

(46 1/2

× 33 1/8 × 17 5/8 inches)

KDS-55A2000: 1292

× 913 × 480 mm

(50 7/8

× 36 × 19 inches)

KDS-60A2000/KDS-60A2010: 1413

× 988× 514 mm

(55 3/4

× 39 × 20 1/4 inches)

Mass:

KDS-50A2000/KDS-50A2010: 34kg (75 lb.)

KDS-55A2000: 38 kg (83 lb. 13 oz.)

KDS-60A2000/KDS-60A2010: 43kg (94 lb. 13 oz.)

Supplied accessories:

Remote control RM-YD010 (1)

Size AA batteries (2)

Operating Instructions (1)

Quick Setup Guide (1)

Warranty Card (1) (A2000)

Product Registration Card (1) (A2000)

Design and specifications are subject to change

without notice.

(Component Video) (VIDEO 2 only):

(Component Video) :

7/8

1/8

Optional accessories:

TV Stand: SU-RS11M(KDS-50A2000/KDS-50A2010)

SU-RS11X

(KDS-55A2000/KDS-60A2000/KDS-60A2010)

Lamp: XL-5200

KDS-50A2000/50A2010/55A2000/60A2000/60A2010

RM-YD010

Replacing the Lamp

The projection lamp, like all lamps, will eventually lose brightness and

functionality, which affects the overall performance of your TV. How long

the lamp maintains its brightness will vary depending upon your usage and

environmental conditions. To maintain the quality of your viewing

experience, Sony recommends that you replace the lamp (1) after

approximately 8,000 hours of use; (2) when the screen becomes dark or the

color looks unusual; (3) when the LAMP LED on the front of the TV blinks;

or (4) when the lamp replacement message appears on the TV screen.

Use a Sony XL-5200 replacement lamp (not supplied) for replacement.

Use of any other lamp may damage the TV.

Do not remove the lamp for any purpose other than replacement. Doing

so may cause injury or fire.

Do not put flammable materials and metal objects inside the lamp

receptacle of the TV after removing the lamp. Doing so may cause fire

or electrical shock. Do not touch the lamp receptacle once the lamp has

been removed.

When the lamp eventually burns out, you may hear a noticeable pop

sound. This is normal and it is inherent to this type of lamp.

In rare instances, the bulb may pop inside the lamp unit, but the lamp

unit is designed to contain all of the broken glass pieces inside the lamp

unit.

This TV's lamp contains mercury and should be disposed of properly.

Consult your local authorities regarding safe disposal. The material

contained in this lamp are similar to those of a fluorescent lamp, so you

should dispose of it in the same way.

How to Replace the

Lamp

Turn off the power on the main unit. Wait several minutes, then unplug

the power cord.

(The cooling fan will continue to operate for about two minutes after

turning the power off.)

Wait at least 30 minutes after unplugging the power cord to allow the

lamp to cool down before replacing it. To avoid being burned, do not

touch the lamp receptacle once the lamp has been removed.

WARNING

Electric appliances can cause fire or high temperature, resulting in

injury or death. Be sure to follow the instructions below.

(Continued)

KDS-50A2000/50A2010/55A2000/60A2000/60A2010

RM-YD010

Take the new lamp out of the box.

Do not touch the glass portion of the new lamp.

Remove the outside lamp cover.

Release the two clamps as shown in the illustration below.

Remove the lamp door.

Turn the screw counterclockwise and slide the lever to the left. Remove

the door.

Pull out the lamp.

Hold the indented grooves on the top corners of the lamp, as shown in

the illustration, and pull the lamp straight out. If the lamp is hard to

remove, pull the right side of the lamp for additional traction.

·Do not shake the lamp. Vibration can damage the lamp or shorten

its life.

·Avoid touching the front glass of a new lamp or the glass of the

lamp receptacle. This may reduce picture quality or lamp life.

Hold this part of the lamp

KDS-50A2000/50A2010/55A2000/60A2000/60A2010

RM-YD010

Put the new lamp into its place.

Insert the new lamp by pressing the two parts firmly into place as shown

in the illustration. Make sure the lamp is securely mounted into the

compartment. Failure to do so may cause a fire or the screen to go dark.

Reattach the lamp door.

Replace the door by inserting the two tabs in the slot from the left side.

Slide the lever to the right and then turn the screw clockwise to secure

the door.

·Do not touch the inside of the lamp compartment.

·The lamp is very hot immediately after use. Never touch the glass

portion of the lamp or the surrounding parts.

·After the used lamp has cooled, place it into the empty box of the

replacement lamp. Never put the used lamp into a plastic bag.

·The lamp compartment is tilted, as shown in the following

illustration.

·If the lamp is not securely reattached, the self-diagnostic function

may be triggered and the POWER LED blinks three times.

(Continued)