background image
3-264-832-
11 (1)
IC Recorder
Operating Instructions
2004 Sony Corporation
Printed in China
ICD-B16/B26
Owner's Record
The model number is located at the rear and the serial number is located inside the battery
compartment. Record the serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
Model No. ICD-B16/B26
Serial No.
Step 1: Installing the Batteries
Slide and lift the battery
compartment lid.
Insert two LR03 (size AAA)
alkaline batteries with
correct polarity, and close the
lid.
If the battery compartment lid
is accidentally detached,
attach it as illustrated.
1
2
Clock setting display appears when you insert batteries for the first time, or
when you insert batteries after the unit has been without batteries for a certain
period of time. Please refer to Steps 2 to 3 in "Step 2: Setting the Clock" to set the
date and time.
Replacing the batteries
The battery indicator on the display
window shows the battery
condition.
When
flashes, replace the
batteries with new ones.
When
flashes, the batteries are
exhausted and the unit will stop
operation.
Battery life*
With continuous use, approx. 18.5
hours recording/9.5 hours playback in
the SP mode and 19.5 hours
recording/10 hours playback in the
LP mode is possible.
* Using Sony alkaline batteries LR03
(size AAA)
* When playing back through the
internal speaker with VOL control at
around 4
The battery life may shorten
depending on the operation of the
unit.
Notes
· Do not use manganese batteries for
this unit.
· When you replace the batteries,
insert the new ones within 3
minutes after you removed the
exhausted ones. Otherwise, the
display may show the clock setting
display or incorrect date and time
when you reinsert the batteries. In
this case, set the date and time
again.
The recorded messages and alarm
setting, however, will remain.
· When replacing the batteries, be
sure to replace both batteries with
new ones.
· Do not charge dry batteries.
· When you are not going to use the
unit for a long time, remove the
batteries to prevent damage from
battery leakage and corrosion.
Clock setting display appears when you insert batteries for the first time, or when you insert battery after the unit has been
without battery for a certain period of time. In this case, proceed from step 2.
Display the clock setting display.
Set the date.
2
Press NxPLAY/STOP.
The month digits will flash.
3
Set the month and day in sequence,
then press NxPLAY/STOP.
The hour digits will flash.
1
2
Press ­ . once to display "SET
DATE".
3
Press NxPLAY/STOP.
The year digits will flash.
1 Tip
To set the date to Year 2004, display
"04Y".
2
Step 2: Setting the Clock
Set the time.
3
3
Set the minute.
4
Press NxPLAY/STOP at the time
signal.
The display will return to "SET
DATE".
5
Press MENU to exit from the menu
mode.
Recording Messages
You can record up to 99 messages in each of the two folders (A and B).
Since a newly recorded message is automatically added behind the last recorded
message, you can start recording quickly without searching for the end of the
last recording.
Note
Before making a long recording, be sure to insert new batteries and check the battery
indicator.
Select the folder.
Start recording.
You do not need to keep pressing zREC/STOP while recording.
1
Press zREC/STOP.
Stop recording.
If you do not change the folder after you stop recording, the next time you
record you will record in the same folder.
To
Do this
pause recording*
Press XPAUSE.
During recording pause, the
OPR indicator flashes in red and
"PAUSE" flashes in the display
window.
release pause and
Press XPAUSE or zREC/STOP.
resume recording
Recording resumes from that point.
(To stop recording after pausing recording, press
STOP.)
listen to the current
Press zREC/STOP or STOP to stop recording,
recording
then press NxPLAY/STOP.
review the current
Press NxPLAY/STOP during recording.
recording instantly
select the microphone
You can select the microphone sensitivity to display
sensitivity
the following by pressing MIC SENS.
HIGH: To record at meeting or in a quiet and/or
spacious place.
LOW: To record for dictation or in a noisy place.
* About one hour after you pause recording, recording pause is automatically released
and the unit goes into the stop mode.
3
2
e.g.
X
PAUSE
Press zREC/STOP again.
The unit stops at the
beginning of the current
recording.
B
Basic Operations
Remaining memory
indicator
* The display selected
with the DISPLAY
button appears.
Information
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY
DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
For the customers in the U.S.A.
INFORMATION
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
­ Reorient or relocate the receiving antenna.
­ Increase the separation between the equipment and
receiver.
­ Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
­ Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
Precautions
On power
· Operate the unit only on 3 V DC. Use two LR03 (size AAA)
alkaline batteries.
On safety
· Do not operate the unit while driving, cycling or operating
any motorized vehicle.
On handling
· Do not leave the unit in a location near heat sources, or in a
place subject to direct sunlight, excessive dust or mechanical
shock.
· Should any solid object or liquid fall into the unit, remove
the batteries and have the unit checked by qualified
personnel before operating it any further.
On noise
· Noise may be heard when the unit is placed near an AC
power source, a fluorescent lamp or a mobile phone during
recording or playback.
· Noise may be recorded when an object, such as your finger,
etc., rubs or scratches the unit during recording.
On maintenance
· To clean the exterior, use a soft cloth slightly moistened in
water. Do not use alcohol, benzine or thinner.
Keep personal credit cards using magnetic coding or spring-
wound watches, etc., away from the unit to prevent possible
damage from the magnet used in the speaker.
If you have any questions or problems concerning your unit,
please consult your nearest Sony dealer.
Backup recommendations
To avoid potential risk of data loss caused by accidental
operation or malfunction of the IC recorder, we recommend
that you save a backup copy of your recorded messages on
a tape recorder, etc.
Current folder
Press FOLDER to
display the folder in
which you wish to
record messages.
Note on recording
Noise may be recorded if an object,
such as your finger, etc., accidentally
rubs or scratches the unit during
recording.
Maximum recording time
The maximum recording time of all
the folders is as follows. You can
record messages for the maximum
recording time in a single folder.
Mode:
SP*
LP**
ICD-B16
5 h.
8h. 15 min.
ICD-B26
10 h.
16 h. 25 min.
(h.: hours/min.: minutes)
* SP: Standard play recording mode
(monaural sound)
** LP: Long play recording mode
(monaural sound)
Notes
· To record in better sound quality,
select the SP mode. For switching
the recording mode, see "Changing
the Recording Mode" on the reverse
side.
· Before making a long recording, be
sure to check the battery indicator.
· The maximum recording time and
the number of messages you can
make varies depending on the
conditions of use.
· When you record messages in the
mixture of SP and LP mode, the
maximum recording time will be
between those for the SP and LP
modes.
· Due to the limitation of the IC
recording system, this unit records
in the minimum recording unit of
approx. 9 seconds, therefore the
following symptoms may occur:
­ When a message is shorter than
the minimum recording unit, it is
still counted as approx. 9 seconds
so the remaining recording time
will decrease by more than the
actual length of the message.
­ When the message is longer than
the minimum recording unit, the
remaining recording time will
decrease by more than the actual
length of the message if it cannot
be divided by the minimum
recording unit without a
remainder.
­The sum of the number on the
counter (elapsed recording time)
and the remaining recording time
may be less than the unit's
maximum recording time.
Remaining memory
indication
During recording, the remaining
memory indicator decreases one by
one.
When the remaining time of
recording reaches 5 minutes, the
last one of the indication flashes.
When the remaining time of
recording reaches 1 minute, the
selected display mode and
"REMAIN" will flash one after the
other in the display window. When
the memory is full, recording
automatically stops and "FULL"
will flash in the display window
with an alarm sound. To continue
recording, first erase some of the
messages.
Notes
· If you press zREC/STOP when the
memory is full, "FULL" will flash
with an alarm sound. Erase some of
the messages before you start
recording again.
· If you press zREC/STOP after you
have recorded 99 messages, "FULL"
will flash with an alarm sound.
Select another folder or erase some of
the messages.
Starting recording
automatically in response
to the sound -- Advanced
VOR function (ICD-B26
only)
When VOR (voice operated
recording) is set to ON in the menu,
recording starts when the recorder
detects sound. ("VOR" is displayed
in the display window.)
Recording stops when no sound is
heard. ("VOR PAUSE" flashes in
the display window.)
Note
VOR function is affected by the sound
around you. Set the MIC SENS to
HIGH or LOW. If recording is not
satisfactory after you have changed
the microphone sensitivity, or for
important recording, set VOR to OFF.
Flashing
* The display selected with the DISPLAY button appears (see the reverse side).
When playing back a previously recorded message, start from Step 1.
When playing back a message you have just finished recording, start from Step 3.
Select the folder.
Select the message number.
1
Press FOLDER to display
the folder you wish to
play back.
Press ­ . or >+ to
display the desired
message number.
>
+: for larger
message number
­ .: for smaller
message number
Selected message number
Current folder
Counter
display*
Playing Back Messages
Start playback.
After playing back one message, the unit stops at the beginning of the next
message. When the continuous play function is set to "ON" (see the reverse
side), the unit stops after playing all messages in a folder.
When the last message on a folder has been played back, the unit stops at the
beginning of the last message.
For private listening
Connect an ear receiver or headphones (not supplied) to the EAR jack. The built-
in speaker will be automatically disconnected. If you plug in headphones, you
will get output from the left channel only. If noise is heard, wipe the
headphones plug.
Other operations
To
Do this
stop at the beginning of
Press STOP.
the current message
stop at the current position
Press NxPLAY/STOP.
(Playback Pause function)*
To resume playback from that point,
press NxPLAY/STOP again.
go back to the beginning
Press ­ . once.
of the current message
skip to the next message
Press >+ once.
go back to previous
Press ­ . or >+ repeatedly.
messages/skip to succeeding
(During stop mode, keep the button
messages
pressed to skip the messages
continuously.)
* You can also pause playback by pressing XPAUSE instead of NxPLAY/STOP.
The OPR indicator will flash in green. After about one hour, the unit goes into the
stop mode at the current position.
2
Turn VOL to adjust the
volume.
EAR jack
1
Press NxPLAY/STOP.
B
Getting started
Troubleshooting
Before taking the unit for repair, check the following
sections. Should any problem persist after you have
made these checks, consult your nearest Sony dealer.
The unit does not operate.
· The batteries have been inserted with incorrect
polarity.
· The batteries are weak.
· The buttons are locked with the HOLD switch. (If
you press any button, "HOLD" will flash three
times.)
No sound comes from the speaker.
· Ear receiver or headphones are plugged in.
· The volume is turned down completely.
"FULL" is displayed and you cannot start
recording.
· The memory is full. Erase some of the messages.
· 99 messages has been recorded in the selected
folder. Select another folder or erase some of the
messages.
Noise is heard.
· An object, such as your finger, etc., accidentally
rubbed or scratched the unit during recording so
that noise was recorded.
· The unit was placed near an AC power source, a
fluorescent lamp or a mobile phone during
recording or playback.
· Plug of the connected microphone was dirty when
recording. Clean the plug.
· Ear receiver/headphones plug is dirty. Clean the
plug.
Recording level is low.
· Press MIC SENS to display "HIGH".
Recording level is unstable (when recording
music, etc.).
· This unit is designed to automatically adjust the
recording level when recording meetings, etc., and
is not suitable for music recording.
"--Y--M--D" or "--:--" is displayed.
· You have not set the clock.
"--Y--M--D" or "--:--" is displayed on the
recorded date or recorded time display.
· The date and time of recording will not be
displayed if you recorded the message when the
clock was not set.
You cannot divide a message.
· You cannot divide a message in a folder which has
99 messages.
· If you divide messages frequently, the unit may
become unable to divide a message.
· You cannot divide a message in the first or the last
1 second of a message.
You cannot combine a message.
· If you combine messages frequently, the unit may
become unable to combine messages.
You cannot record messages up to the
maximum recording time.
· If you record messages in a mixture of SP and LP
modes, the recordable time varies from the
maximum SP mode recording time to the
maximum LP mode recording time.
· No more recording can be made when 99 messages
each have been recorded in both A and B folders.
· Due to the limitation of the IC recording system,
this unit records in the minimum recording unit of
approx. 9 seconds. If the length of each message
cannot be divided by the minimum recording unit,
the remaining recording time may decrease by
more than the total length of the messages.
The unit does not operate correctly.
· Take out the battery and insert it again.
Please note that recorded messages may be erased
during service or repair work.
2
Counter display (or the
selected display mode)
STOP
Nx
PLAY/STOP
MIC SENS
* The "ALARM" display
may appear instead of
the "MODE" display.
Current
message
number
Counter display*
1 Tip
This unit does not have a power on/off
switch. The display is shown at all
times.
Playing back a message
repeatedly
-- Repeat Play
During playback, press
Nx
PLAY/STOP for more than
one second.
"
" will be displayed and the
selected message will be played
back repeatedly.
To resume normal playback, press
Nx
PLAY/STOP again. To stop
playback, press STOP.
Playing the beginning of
each message
-- Scanning Play
During stop mode, press
Nx
PLAY/STOP for more than
one second.
"SCAN" will be displayed in the
display window and the first 5
seconds of each message in the
selected folder will be played back.
When you find the desired
message, press NxPLAY/STOP.
The message will be played back
until the end.
Playing back all messages
in a folder continuously
-- Continuous Play
You can select the continuous play
mode with the CONT in the menu.
When you set CONT to ON, you
can play back all messages in a
folder continuously.
Searching forward/
backward during playback
(Cue/Review)
To search forward, keep >+
pressed during playback and
release the button at the point you
wish to resume playback.
To search backward, keep ­ .
pressed during playback and
release the button at the point you
wish to resume playback.
If you keep >+ or ­ .pressed
for more than 10 seconds, the unit
starts to search at higher speed.
For the first 10 seconds of cue/
review, fast playback sound can be
heard. When searching at a higher
speed, playback sound will not be
heard.
During cue/review, the counter
will be displayed, regardless of the
display mode setting.
1 Tip
When fast playback is done to the end
of the last message, "END" flashes 3
times. (You cannot hear the playback
sound.) If you keep ­ . pressed
while "END" is flashing, the messages
are played back rapidly, and normal
playback will start at the point you
release the button.
When "END" stops flashing and the
OPR indicator goes off, the unit will
stop at the beginning of the last
message.
If the last message is long and you
wish to start playback at a later part of
the message, keep >+ pressed to
play back the message to the end and
then press ­ . while "END" is
flashing to go back to the desired
point .
(For messages other than the last one,
go to the beginning of the next
message and play backward to the
desired point.)
1
Press MENU to enter the menu
mode.
1
Press ­ . or >+ to select
the digits of the year.
1
Press ­ . or >+ to select
the digits of the hour.
2
Press NxPLAY/STOP.
The minute digits will flash.
2
Speak to the
built-in
microphone.
OPR indicator
(lights in red during
recording.)
Message 1
Message 2
Blank space
Newly recorded message
OPR indicator
(lights in green during
playback.)
The memory is
nearly full.
1
Microphone
sensitivity
Recording mode
Number of
messages in a folder
Number of
messages
in a folder
STOP
You can stop recording by
pressing STOP instead of
z
REC/STOP.
3


background image
You can erase the recorded messages one by one or all messages in a folder at a
time.
Note that once a recording has been erased, you cannot retrieve it.
Erasing messages one by one
When a message is erased, the remaining messages will advance and
renumbered so that there will be no space between messages.
1
Press ERASE while playing back
the message you want to erase
or press ERASE for more than 1
second during stop mode.
A beep will sound and the message
number and "ERASE" will flash
while the first and last 5 seconds of
the message is played back 10
times.
2
Press ERASE while the message
is being played back.
The message is erased and the
remaining messages will be
renumbered. (For example, if you
erase Message 3, Message 4 will be
renumbered as Message 3. When
erasing is completed, the unit will
stop at the beginning of the
following message.)
Erasing Messages
To cancel erasing
Press STOP before step 2.
To erase other messages
Repeat steps 1 and 2.
To erase a message
partially
First divide the message and then
follow the steps to erase the
message.
Erasing all messages in a folder
To cancel erasing
Press STOP before step 3.
B
Various Ways of Recording
Adding a Recording to a
Previously Recorded Message
You can add a recording to the message being played
back.
The added recording will be placed after the current
message and counted as a part of the message.
MIC
Tape recorder, TV,
radio, etc.
EAR,
EARPHONE,
v
or REC OUT
3
While the display
is flashing, press
ERASE.
Moving Messages to a Different
Folder -- Move Function
You can move the recorded messages to another folder.
Example: Moving Message 3 in Folder A to Folder B
1 Play back the message you want
to move.
2 While playing back the message,
press FOLDER to flash the
indication of the folder to which
you want to move the message
(B in this case).
The first and last 5 seconds of the
message will be played back 10
times, while the folder indication
and "MOVE" flash.
3 Press NxPLAY/STOP.
The message is moved in the
destination folder. Messages are
sorted in order of the recorded
date and time.
To cancel moving the message(s)
Press STOP before step 3.
Note
The move function does not duplicate a message in another
folder. When you move a message to another folder, the one
in the previous folder will be deleted.
Playing Back a Message at a
Desired Time with an Alarm
You can sound an alarm and start playback of a selected
message at a desired time.
1 Use FOLDER and ­ ./
>
+ to select the folder
and the message you want
to play back.
2 Enter the alarm setting mode.
1
Press MENU.
The unit enters the menu mode
and "ALARM OFF" will be
displayed.
(If "ALARM ON" is displayed,
the alarm has been set. If you do
not wish to change the setting,
press MENU and exit the menu
mode.)
Note
"ALARM OFF (or ON)" will not appear and the
alarm cannot be set if the clock has not been set or no
message has been recorded in the selected folder.
2
Press NxPLAY/STOP.
"OFF" starts to flash.
3
Press ­ . or >+ to flash
"ON".
4
Press NxPLAY/STOP.
"DATE" will flash in the display
window.
3 Set the alarm date.
To play back on a desired date
(the message will be played back at the same time on
the same date every year until you erase the
message)
1
Press NxPLAY/STOP while
"DATE" is flashing.
The month digits will flash.
Note
You cannot set an alarm for a
specific year. "--Y 1M 1D" will be
displayed.
2
Press ­ . or >+ to select
the month digits and press
Nx
PLAY/STOP.
The day digits will flash.
3
Press ­ . or >+ to select
the day digits.
To play back once a week
Press ­ . or >+ to select
the day of the week.
To play back at the same time
every day
Press ­ . or >+ to select
"DAILY".
During
playback of
Message 3
After
adding a
recording
Message 4
at Conference room A
Message 4
Added recording
1 During playback, press zREC/
STOP for more than 1 second.
The REC indicator appears and
"ADD" flashes three times on the
display window.
The OPR indicator will turn red.
The new recording will be added at
the end of the current message.
2 Press zREC/STOP or STOP to stop the
recording.
Recording with an External
Microphone or from Other
Equipment
1 Connect a plug-in-power type microphone or
other equipment to the MIC (PLUG IN POWER)
jack.
When recording with an external
microphone
When you connect an external microphone, the built-in
microphone is automatically cut off. When a plug in
power type microphone is connected, power is
automatically supplied to the microphone from the IC
recorder.
When recording from other equipment
2 Follow the steps in "Recording messages" to
record messages.
Notes
· Make sure that the plugs are connected securely.
· We recommend you make a trial recording to check the
connections and volume control.
· When connecting equipment other than Sony's, refer to the
instruction manual of the equipment.
Starting recording
automatically in response to the
sound -- Advanced VOR function
(ICD-B26 only)
VOR ON:
The VOR (Voice Operated Recording)
function is activated. Recording starts when
the unit detects sound and stops when no
sound is heard, eliminating recording from
soundless period.
VOR OFF:
The VOR function is disabled. Normal
recording operation is selected.
1 Press MENU to enter the menu
mode.
2 Press ­ . or >+ to display
"VOR" and press NxPLAY/
STOP.
"OFF (or ON)" will flash.
3 Press ­ . or >+ to select
"ON" or "OFF" and press
Nx
PLAY/STOP.
Now the setting is completed.
4 Press MENU to exit the menu
mode.
MIC
4 Press NxPLAY/STOP.
The hour digits will flash.
5 Set the alarm time.
1
Press ­ . or >+ to select
the hour digits and press
Nx
PLAY/STOP.
The minute digits will flash.
2
Press ­ . or >+ to select
the minute digits and press
Nx
PLAY/STOP.
6 Press MENU to exit the menu
mode.
"," is displayed when the number of the message with
alarm setting is selected.
At the set time, the alarm will sound for about 10 seconds
and the selected message will be played back.
During playback, "ALARM" will flash in the display
window.
When the playback ends, the unit will stop automatically
at the beginning of that message.
To listen to the same message again
Press NxPLAY/STOP. The same message will be played
back from the beginning.
To cancel the alarm setting before the
playback starts
Press STOP while the alarm sound is heard. You can stop
even when the HOLD function is activated.
Notes
· You cannot set the alarm if you have not set the clock or there
is no message in the selected folder (the unit will not enter
the alarm setting mode when you press MENU in Step 2).
· If you try to set the alarm to play back a message at a
previously set time on another message, "PRE SET" will be
displayed, preventing new settings.
· If the alarm time comes while another message is being
played back with an alarm, the playback stops and the new
message will be played back.
· If the alarm time comes during recording, alarm will sound
for 10 seconds after the recording is finished and playback
begins. "," will flash when the alarm time comes.
· If more than one alarm time comes during recording, only
the first message will be played back.
· When the alarm time comes when the unit is in the menu
mode, alarm will sound and the menu mode will be
cancelled.
· If you erase the message you set the alarm to play back, the
alarm setting will be cancelled.
· If you divide a message with the playback alarm, playback
will stop at the point you divided a message.
· If you combine messages with the playback alarm, the alarm
setting will be cancelled.
· You can adjust the playback volume with the VOL control.
· If the alarm time comes during erasing, alarm will sound for
10 seconds after the erasing is finished and playback begins.
· Alarm setting will not be cancelled when the alarm playback
finishes. To cancel alarm setting, see below.
To cancel the alarm setting or change the
alarm time
1 Select the message you set the alarm to play back, and
press MENU.
"ALARM ON" will be displayed.
2 Press NxPLAY/STOP to flash "ON".
3 To cancel the alarm setting: Press ­ . or >+ to
flash "OFF" and press NxPLAY/STOP.
To change the alarm date and time: Press
Nx
PLAY/STOP. When the alarm date is displayed,
follow the steps 3 to 5 above to change the alarm date
and time.
4 Press MENU to exit the menu mode.
Preventing Accidental Operation
-- HOLD function
Slide the HOLD switch in the direction of
the arrow. "HOLD" will flash three times,
indicating that all the functions of the
buttons are locked.
To cancel the HOLD function, simply
slide the HOLD switch in the opposite
direction.
Note
When the HOLD function is activated during recording, cancel
the HOLD function first to stop recording.
1 Tip
Even if the HOLD function is activated, you can stop the alarm
playback. To stop the alarm or playback, press STOP.
Selecting the Display Mode
You can select the display mode for the stop, recording
and playback modes. (If the unit is left unoperated for
more than 3 seconds in the stop mode, the display will
show the current time, regardless of the display mode
setting.)
Each time you press DISPLAY, the display mode will
change as shown below:
Counter:
Elapsed playback/recording
time in one message
m
Remaining
recording time:
m
Recorded date*:
The date the current message
was recorded.
m
Recorded time**:
The time the current message
was recorded.
* If the clock has not been set, "--Y--M--D" will be displayed.
**If the clock has not been set, "--:--" will be displayed.
To turn off the display
This unit does not have a power on/off switch. The
display is shown at all times, which will not almost
influence the battery life. To turn off the display, slide the
HOLD switch in the direction of the arrow in the stop
mode.
"HOLD" will flash for three times and then the display
turns off in the window. To turn on the display, slide the
HOLD switch in the opposite direction.
Turning off the Beep Sound
BEEP ON:
A beep will sound to indicate that operation
has been accepted.
BEEP OFF: No beep sound will be heard except for the
alarm and timer.
1 Press MENU to enter the menu
mode.
2 Press ­ . or >+ to display
"BEEP ON (or OFF)" and press
Nx
PLAY/STOP.
"ON (or OFF)" will flash.
3 Press ­ . or >+ to select
"ON" or "OFF" and press
Nx
PLAY/STOP.
The setting is completed.
4 Press MENU to exit the menu
mode.
Changing the Recording Mode
SP: You can record with better sound (monaural sound).
LP: You can record for longer time (monaural sound).
1 Press MENU to enter the menu
mode.
2 Press ­ . or >+ to display
"MODE" and press NxPLAY/
STOP.
"SP (or LP)" will flash.
3 Press ­ . or >+ to select
"SP" or "LP" and press
Nx
PLAY/STOP.
Now the setting is completed.
4 Press MENU to exit the menu
mode.
The selected recording mode is
displayed.
Index to Parts and Controls
Main unit
MIC jack
(PLUG IN POWER)
EAR (earphone) jack
OPR (operation) indicator
z
REC (record) /STOP
X
PAUSE
­ .REVIEW/
>
+CUE
Nx
PLAY/STOP·
EXECUTE
HOLD
VOL (volume)
MIC
(built-in microphone)
Display window
FOLDER
DIVIDE
DISPLAY
MIC SENS
(microphone sensitivity)
MENU
ERASE
Speaker
STOP
Rear
Battery
compartment
Hook for handstrap
(not supplied)
Playing Back All Messages in a
Folder Continuously
CONT ON: You can play back all messages in a folder
continuously.
CONT OFF: Playback stops at the end of each message.
1 Press MENU to enter the menu
mode.
2 Press ­ . or >+ to display
"CONT" and press NxPLAY/
STOP.
"OFF (or ON)" will flash.
3 Press ­ . or >+ to select
"ON" or "OFF" and press
Nx
PLAY/STOP.
Now the setting is completed.
4 Press MENU to exit the menu
mode.
Specifications
Recording media
Built-in flash memory, Monaural recording
Recording time
ICD-B16:
SP: 5 hours
LP: 8 hours 15 minutes
ICD-B26:
SP: 10 hours
LP: 16 hours 25 minutes
Frequency range
160 Hz - 3 300 Hz
Speaker
approx. 3.2 cm (1 5/
16 in.) dia.
Power output
250 mW
Input/Output
·Earphone jack (minijack) for 8 - 300 ohms ear
receiver/headphones
·Microphone jack (minijack, monaural)
Plug in power
Minimum input level 0.6 mV
3 kilohms or lower impedance microphone
Power requirements
Two LR03 (size AAA) alkaline batteries: 3 V DC
Dimensions (w/h/d) (not incl. projecting parts and
controls)
44.5
× 105.3 × 14.0 mm (1 13/
16 × 4
1/
4 ×
9/
16 in.)
Mass (incl. batteries)
69 g (2.5 oz)
Supplied accessories
LR03 (size AAA) alkaline batteries (2) (For the
U.S.A. only)
Optional accessories
Electret Condenser Microphone ECM-C10,
ECM-DM5P, ECM-Z60
Audio connecting cable RK-G64HG (excluding
Europe)
Your dealer may not handle some of the above listed
optional accessories. Please ask the dealer for detailed
information.
Design and specifications are subject to change without
notice.
Erase Message 3
Before erasing
After erasing
Remaining messages are renumbered.
Message 3
HOLD
Display window
Remaining battery
indicator
Repeat play indicator
Recording mode
indication
REC (recording)
indicator
Selected message
number/Mode
indication of the
menu (ON, OFF, etc.)
Counter /Remaining time indication /Recording date
indication /Current time indication (15:30, etc.) /Menu
indication (ALARM, BEEP, etc.) /Messages (ERASE, HOLD,
etc.)
Remaining memory indicator
Folder indication
Alarm indicator
Microphone sensitivity
indication
Message 1
Message 2
Message 3
Message 4
Message 5
Message 4
Message 3
Message 2
Message 1
Message 1 Message 2 Message 3 Blank space
Message 1 Message 2
Folder B
e.g.
Folder A
Blank space
Message 1 Message 2
Message 3
1
Press FOLDER
to select the
folder you
want to erase.
2
While pressing STOP, press
ERASE for more than 1 second.
"ALL ERASE" will flash for 10
seconds.
Message 3
Message 3
Meeting at 2 o'clock
on December 1.
B
Other Functions
Dividing a Message into Two/
Combining Messages
You can divide a message, or combine messages.
· You can divide a message into two while recording/
playing back messages.
· You can combine messages in stop mode.
Note
Due to the recording system of an IC recorder, you may not be
able to divide or combine messages in some cases (see
"Troubleshooting").
Dividing a Message
You can divide a message during recording or playback,
so that the message is divided into two and the new
message number is added to the divided message. By
dividing a message, you can easily find the point you want
to play back when you make a long recording such as a
meeting.
You can divide messages until the total number of
messages in the folder becomes 99.
While recording or playing back a message, press
DIVIDE at the point you want to divide.
· When you press DIVIDE during recording:
The new message number is added at the
point you pressed the button, and the
new message number flashes for 3
seconds. The message will be divided
into two; however, the messages will be
recorded without a break.
1 Tip
You can divide a message during recording pause.
· When you press DIVIDE during playback:
The message is divided into two at the
point you pressed the button, and the
new message number flashes for 3
seconds. The message numbers of the
following messages will increase by
one.
1 Tip
You can divide a message after you have paused playback with
X
PAUSE.
To play the divided message
Press ­. or >+ to display the message number as the
divided messages each have message numbers.
1 To play the divided messages continuously
Select ON for CONT in the menu as described in "Playing Back
All Messages in a Folder Continuously".
Notes
· If 99 messages have been recorded in a folder, you cannot
divide a message. In that case, reduce the number of
messages to 98 or less by erasing unnecessary messages or by
moving some of the messages to another folder before
dividing a message.
· If you divide a message with an alarm setting, the alarm
setting remains only with the former message divided.
Combining Messages
You can combine two messages into one.
In stop mode, follow the steps below:
1 Press ­ . or >+ to display
the number of the second of the
two messages you want to
combine.
2 While pressing ERASE, press
DIVIDE for more than 1 second.
"CMB" (combine) will flash for 10
seconds.
3 Press ERASE while the display is flashing.
The two messages are combined into one and the
messages will be renumbered as in the illustration
above.
To cancel erasing
Press STOP before step 3.
Notes on dividing and combining messages
When recording with an IC recorder, the following symptoms
may occur because of the limitation of the system, however,
they are not malfunction.
· If you divide or combine messages frequently, the unit may
become unable to divide or combine messages.
· You cannot divide a message in the first or the last 1 second.
· After combining messages, the latter message's alarm setting
will be erased.
· You cannot combine messages of different recording modes.
Message 1 Message 2 Message 3 Message 4
Message 1
Message 2
Message 3
The message numbers decrease.
Messages are combined.
Message 3
A message is divided.
Recording continues
Message 1 Message 2
Message 4
The message numbers increase.
A message is divided.
Message 1
Message 2
Message 3
Message 1
Message 2
Message 3
mini-plug (monaural)
External
microphone
(not supplied)
Audio connecting
cable with
attenuator
(not supplied)
mini-plug (monaural)
mini-plug (stereo
or monaural)
,