background image
SERVICE MANUAL
LEVEL
2
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
DSC-P10/P12
·For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987622751.pdf).
·For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987622741.pdf).
· This service manual contains information for Japanese model as well.
· Reference No. search on printed wiring boards is available.
· Note in Lens Frame Installation
· HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Ver 1.0 2003. 03
DIGITAL STILL CAMERA
On the JK-243, JK-244 and SY-83 boards
This service manual procides the information that is premised
the circuit board replacement service and not intended repair
inside the JK-243, JK-244 and SY-83 boards.
Therefore, schematic diagram, printed wiring board and
electrical parts list of the JK-243, JK-244 and SY-83 boards are
not shown.
The following pages are not shown.
JK-243, JK-244 boards
Schematic diagram ......................... Pages 4-35 to 4-36
Printed wiring board ........................ Pages 4-51 to 4-52
Electrical parts list ........................... Pages 5-6
SY-83 board
Schematic diagram ......................... Pages 4-9 to 4-28
Printed wiring board ........................ Pages 4-43 to 4-46
Electrical parts list ........................... Pages 5-9 to 5-13
The above-described information is shown in service
manual Level 3.
Photo: DSC-P10
US Model
Canadian Model
DSC-P10
AEP Model
UK Model
DSC-P10/P12
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
DSC-P10


background image
-- 2 --
DSC-P10/P12
SPECIFICATIONS
COVER
COVER
White balance
Flash, Automatic, Daylight, Cloudy,
Fluorescent, Incandescent
Data format (DCF compliant)
Still images: Exif Ve r. 2.2 JPEG
compliant, GIF (for Clip Motion),
DPOF compatible
Audio with still image:
MPEG1 compliant (Monaural)
Moving images:
MPEG1 compliant (Monaural)
Recording media
"Memory Stick"
Flash
Recommended distance (ISO set to Auto):
0.5 m to 3.5 m (19 3/4 inches to
11 feet 5 3/16 inches) (W)
0.6 m to 2.5 m (23 5/8 inches to 8 feet
27/16 inches) (T)
[Output connectors]
A/V OUT (MONO) (Monaural)
Minijack
Video: 1 Vp-p, 75
, unbalanced,
sync negative
Audio: 327 mV (at a 47 k
load)
Output impedance 2.2 k
USB jack mini-B
[General]
Used battery pack
NP-FC11
Power requirements
3.6 V
Power consumption (during shooting)
1.6 W
Operating temperature
0
°C to 40°C (32°F to 104°F)
Storage temperature
­20
°C to +60°C (­ 4 °F to +140°F)
Dimensions
108
×51.5×35.1 mm
(4 3/8
×21/8×17/16 inches)
(W/H/D, excluding maximum
protrusions)
Mass
Approx. 200 g (7 oz) (including
battery pack NP-FC11, "Memory
Stick" and wrist strap)
Built-in microphone
Electret condenser microphone
Built-in speaker
Dynamic speaker
Exif Print Compatible
PRINT image matching II Compatible
Storage temperature
­20
°C to +60°C (­ 4 °F to +140°F)
Dimensions
Approx. 48
×29×81 mm
(1 15/16
×1 3/16×3 1/4 inches)
(W/H/D)
Mass
Approx. 130 g (5 oz)
x NP-FC11 battery pack
Used battery
Lithium-ion battery
Maximum voltage
DC 4.2 V
Nominal voltage
DC 3.6 V
Capacity 2.8 Wh (780 mAh)
Accessories
·NP-FC11 battery pack (DSC-P12: 2, DSC-P10: 1)
·AC-LS5 AC Adaptor
·Power cord (mains lead)
·A/V connecting cable
·USB cable
·Wrist strap
·"Memory Stick" (32 MB)
·CD-ROM (USB driver SPVD-010)
·Operating instructions
·Soft carrying case (DSC-P12 only)
Design and specifications are subject to change
without notice.
x Camera
[System]
Image device
9.04 mm (1/1.8 type) color CCD
Primary color filter
Total pixels number of camera
Approx. 5 250 000 pixels
Effective pixels number of camera
Approx. 5 090 000 pixels
Lens
3
× zoom lens
f = 7.9 ­ 23.7 mm (5/16 ­
15/16 inches) (38 ­ 114 mm
(1 1/2 ­ 4 1/2 inches) when converted
to a 35 mm still camera)
F2.8 ­ 5.2
Exposure control
Automatic exposure, Scene selection
(7 modes)
[LCD screen]
Used LCD panel
3.8 cm (1.5 type) TFT drive
Total number of dots
123 200 (560
×220) dots
x AC-LS5 AC Adaptor
Rated input voltage
100 to 240 V AC, 50/60 Hz, 11 W,
0.16 to 0.09 A
Rated output voltage
DC 4.2 V, 1.5 A in operating mode
Operating temperature
0
°C to 40°C (32°F to 104°F)


background image
-- 3 --
DSC-P10/P12
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
·Keep the temperature of the soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.


background image
-- 4 --
DSC-P10/P12
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
Note for Repair ································································ 1-1
1-2.
Discharging of the ST-81 Flexible Board's Charging
Capacitor (C001) ····························································· 1-1
1-3.
Precaution on Replacing the Video Lens or the SY-83
Board ··············································································· 1-2
1-4.
Note in Lens Frame Installation ······································ 1-2
1-5.
Description on Self-diagnosis Display ···························· 1-3
2.
DISASSEMBLY
2-1.
Battery Lid ······································································· 2-3
2-2.
Cabinet (Rear) Assembly ················································· 2-3
2-3.
LCD Module ···································································· 2-4
2-4.
Cabinet Front Assembly ·················································· 2-4
2-5.
Control Switch Block ······················································ 2-5
2-6.
Cabinet (Lower) Assembly ·············································· 2-6
2-7.
Lens Block Assembly ······················································ 2-6
2-8.
ST-81 Board ····································································· 2-7
2-9.
SY-83 Board ···································································· 2-7
2-10. MS-130 Board ································································· 2-8
2-11. SW-386 Board ································································· 2-8
2-12. JK-244 Board ·································································· 2-9
2-13. CD-434 Board ································································· 2-9
2-14. Circuit Boards Location ················································ 2-10
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram (1/2) ··········································· 3-1
3-2.
Overall Block Diagram (2/2) ··········································· 3-3
3-3.
Power Block Diagram (1/2) ············································· 3-5
3-4.
Power Block Diagram (2/2) ············································· 3-7
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagrams ············································· 4-1
4-2.
Schematic Diagrams ························································ 4-5
CD-434 (CCD IMAGER) ··············································· 4-7
SW-386 (1/2) (CONTROL SWITCH) ·························· 4-29
SW-386 (2/2)
(LCD DRIVE, TIMING GENERATOR) ····················· 4-31
ST-81 (FLASH DRIVE) ··············································· 4-33
MS-130 (MEMORY STICK CONNECTOR) ·············· 4-37
CONTROL SWITCH BLOCK ····································· 4-38
4-3.
Printed Wiring Boards ··················································· 4-39
CD-434 ·········································································· 4-41
SW-386 ·········································································· 4-47
ST-81 ············································································· 4-49
MS-130 ·········································································· 4-53
4-4.
Waveforms ····································································· 4-56
4-5.
Mounted Parts Location ················································ 4-57
5.
REPAIR PARTS LIST
5-1.
Exploded Views ······························································· 5-2
5-1-1. Cabinet Section ································································ 5-2
5-1-2. Lens Section ···································································· 5-3
5-1-3. Battery Holder Section ···················································· 5-4
5-2.
Electrical Parts List ························································· 5-5
Section
Title
Page


background image
1-1
SECTION 1
SERVICE NOTE
DSC-P10/P12
COVER
COVER
1-2. DISCHARGING OF THE ST-81
FLEXIBLE BOARD'S CHARGING
CAPACITOR (C001)
The charging capacitor (C001) of the ST-81 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 k/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don't pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don't press down at wire of connector.
It is possible that a wire is snapped.
R:1 k/1 W
(Part code:
1-215-869-11)
Capacitor
ST
-81