background image
DCR-TRV8/TRV8E/TRV10/TRV10E
RMT-808/809/811/812
US Model
Canadian Model
DCR-TRV8/TRV10
AEP Model
UK Model
Australian Model
Chinese Model
DCR-TRV8E/TRV10E
E Model
Hong Kong Model
DCR-TRV8/TRV8E/TRV10/TRV10E
Tourist Model
DCR-TRV10/TRV10E
SERVICE MANUAL
DIGITAL VIDEO CAMERA RECORDER
MICROFILM
D300 MECHANISM
Photo: DCR-TRV10
RMT-811
DCR-TRV8/TRV10:
NTSC model
DCR-TRV8E/TRV10E: PAL model
For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL
ADJUSTMENT MANUAL
D MECHANISM " (original: 9-973-815-
11, supplement: 9-973-815-81) and "DV MECHANICAL
ADJUSTMENT MANUAL
D200 MECHANISM " (original: 9-973-
981-11).
SPECIFICATIONS
-- Continued on next page --
Ver 1.5 2001. 11


background image
-- 2 --
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE WITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
· SUPPLIED ACCESSORIES
Check that the following accessories are supplied with your
camcorder.
· DIFFERENCE TABLE
DCR-TRV8
NTSC
RMT-808
10
×
120
×
--
--
IN/OUT
IN/OUT
Model
Color System
Remote Commander
Lens
Optical
Digital
Memory Stick
Memory Key
DV
AUDIO/VIDEO
DCR-TRV8E
PAL
RMT-808
RMT-809 *
10
×
120
×, 40 × *
--
--
IN/OUT
* OUT_ONLY
IN/OUT
* OUT_ONLY
DCR-TRV10E
PAL
RMT-811
RMT-812 *
10
×
120
×, 40 × *
g
g
IN/OUT
* OUT_ONLY
IN/OUT
* OUT_ONLY
DCR-TRV10
NTSC
RMT-811
10
×
120
×
g
g
IN/OUT
IN/OUT
*: AEP, UK model
· Abbreviation
AUS:
Australian model
JE:
Tourist model
CND:
Canadian model
CN:
Chainese mode
HK:
Hong Kong model


background image
-- 3 --
TABLE OF CONTENTS
SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS ····························· 6
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ································································ 6
SELF-DIAGNOSIS FUNCTION
1.
SELF-DIAGNOSIS FUNCTION ······································· 7
2.
SELF-DIAGNOSIS DISPLAY ·········································· 7
3.
SERVICE MODE DISPLAY ············································· 7
3-1.
Display Method ·································································· 7
3-2.
Switching of Backup No. ··················································· 7
3-3.
End of Display ···································································· 7
4.
SELF-DIAGNOSIS CODE TABLE ··································· 8
1.
GENERAL
Welcome! ··················································································· 1-1
Checking supplied accessories ·················································· 1-1
Quick Start Guide ······································································ 1-1
Getting Started ··········································································· 1-2
Using this manual ·································································· 1-2
Step 1 Preparing the power supply ······································· 1-2
Step 2 Inserting a cassette ···················································· 1-4
Recording ­ Basics ···································································· 1-4
Recording a picture ································································ 1-4
Checking the recording
­ END SEARCH/EDIT SEARCH/Rec Review ···················· 1-7
Playback ­ Basics ······································································ 1-7
Playing back a tape ································································ 1-7
Viewing the recording on TV ················································ 1-9
Advanced Recording Operations ··············································· 1-9
Photo recording ······································································ 1-9
Using the wide mode ··························································· 1-10
Using the fader function ······················································ 1-11
Using special effects ­ Picture effect ··································· 1-11
Using special effects ­ Digital effect ··································· 1-12
Adjusting the white balance manually ································· 1-13
Using the PROGRAM AE function ····································· 1-13
Adjusting the exposure manually ········································ 1-14
Focusing manually ······························································· 1-14
Advanced Playback Operations ··············································· 1-15
Playing back a tape with picture effects ······························ 1-15
Playing back a tape with digital effects ······························· 1-15
Quickly locating a scene using the
zero set memory function ····················································· 1-15
Searching a recording by date ­ Date search ­ ···················· 1-16
Searching the boundaries of recorded tape by title
­ Title search ········································································ 1-16
Searching for a photo ­ Photo search/Photo scan ················ 1-16
Editing ····················································································· 1-17
Dubbing a tape ····································································· 1-17
Editing partially on a DV tape ­ DV synchro-editing
(DCR-TRV10E only) ··························································· 1-18
Audio dubbing ····································································· 1-18
Superimposing a title ··························································· 1-19
Making your own titles ························································ 1-20
Labeling a cassette ······························································· 1-20
Customizing Your Camcorder ················································· 1-21
Changing the MENU settings ·············································· 1-21
Resetting the date and time ·················································· 1-22
Memory Stick Operations ························································ 1-23
Using a memory stick ­ introduction ··································· 1-23
Recording still images on memory sticks
­ Memory photo recording ·················································· 1-24
Recording an image from a mini DV tape
as a still image ····································································· 1-25
Copying still images from a recorded tape ­ Photo save ······· 1-26
Viewing a still picture ­ Memory photo playback ··············· 1-26
Superimposing a still picture in a memory stick on a moving
picture­ M. CHROM/M. LUMI/C. CHROM ······················ 1-27
Preventing accidental erasure ­ Image protection ··············· 1-28
Writing a print mark ­ PRINT MARK ································ 1-29
Deleting images ··································································· 1-29
Playing back images in a continuous loop
­SLIDE SHOW ··································································· 1-30
Additional Information ···························································· 1-30
Usable cassettes ··································································· 1-30
Troubleshooting ··································································· 1-31
Self-diagnosis display ·························································· 1-32
Warning indicators and messages ········································ 1-32
Using your camcorder abroad ·············································· 1-33
Maintenance information and precautions ··························· 1-33
Quick Reference ······································································ 1-34
Identifying the parts and controls ········································ 1-34
2.
DISASSEMBLY
2-1.
LCD PANEL (PD-110 BOARD,
INVERTOR TRANS UNIT) ··········································· 2-1
2-2.
FRONT PANEL ASSEMBLY ········································· 2-2
2-3.
CABINET (L), BT PANEL ASSEMBLY ······················· 2-2
2-4.
EVF ················································································· 2-3
2-5.
LB-60 BOARD ································································ 2-3
2-6.
DD-123 BOARD, VC-217 BOARD ······························· 2-4
2-7.
MECHANISM DECK ····················································· 2-4
2-8.
CS FLAME ASSEMBLY ················································ 2-5
2-9.
LENS, OUTER CONNECTOR (HOT SHOE),
JK-170 BOARD ······························································ 2-5
2-10. MS SHASSIS,
CONTROL SWITCH BLOCK (PS-4550) ······················ 2-6
2-11. CK-84 BOARD, SPEAKER ··········································· 2-6
2-12. LCD, CONTROL SWITCH BLOCK ····························· 2-7
2-13. SERVICE POSITION
(Mainly for voltage measurement and check) ················· 2-8
2-14. CIRCUIT BOARD LOCATION ····································· 2-9
2-15. FLEXIBLE BOARDS LOCATION ······························ 2-10
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM (TRV8/TRV8E) ········· 3-1
3-2.
OVERALL BLOCK DIAGRAM (TRV10/TRV10E) ····· 3-5
3-3.
POWER BLOCK DIAGRAM ········································· 3-9
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ············································ 4-4
· FP-83 (CCD IMAGER)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ······························ 4-6
· VC-217 (FOCUS/ZOOM MOTOR DRIVE)(1/11)
SCHEMATIC DIAGRAM ······························ 4-9
· VC-217 (CAMERA)(2/11)
SCHEMATIC DIAGRAM ···························· 4-12
· VC-217 (BLOCKING COMPRESS)(3/11)
SCHEMATIC DIAGRAM ···························· 4-15
· VC-217 (VIDEO INTERFACE)(4/11)
SCHEMATIC DIAGRAM ···························· 4-18
· VC-217 (DV PROCESS)(5/11)
SCHEMATIC DIAGRAM ···························· 4-21
· VC-217 (REC/PB HEAD AMP)(6/11)
SCHEMATIC DIAGRAM ···························· 4-25
· VC-217 (VIDEO IN/OUT)(7/11)
SCHEMATIC DIAGRAM ···························· 4-29


background image
-- 4 --
· FP-91 (TOP/END SENSOR), FP-92 (TAPE LED),
FP-242 (S/T REEL SENSOR)
PRINTED WIRING BOARDS ····················· 4-33
· VC-217 (MECHANISM CONTROL)(8/11)
SCHEMATIC DIAGRAM ···························· 4-34
· VC-217 (SERVO)(9/11)
SCHEMATIC DIAGRAM ···························· 4-37
· VC-217 (HI CONTROL)(10/11)
SCHEMATIC DIAGRAM ···························· 4-41
· VC-217 (AUDIO)(11/11)
SCHEMATIC DIAGRAM ···························· 4-45
· FP-82 (VC-CK CONNECT)
PRINTED WIRING BOARD ······················· 4-47
· VC-217 (FOCUS/ZOOM MOTOR DRIVE, CAMERA,
BLOCKING COMPRESS, VIDEO INTERFACE,
DV PROCESS, REC/PB HEAD AMP, VIDEO IN/OUT,
MECHANISM CONTROL, SERVO, HI CONTROL,
AUDIO)
PRINTED WIRING BOARD ······················· 4-48
· CK-84 (FUNCTION SWITCH, IR),
CF4550 (CONTROL DIAL),
FP-91 (PANEL REV/CLOSE)
PRINTED WIRING BOARDS ····················· 4-54
· CK-84 (FUNCTION SWITCH, IR),
CF4550 (CONTROL DIAL),
FP-91 (PANEL REV/CLOSE)
SCHEMATIC DIAGRAMS ·························· 4-57
· JK-170 (AV IN/OUT)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-61
· MA-358 (MIC AMP, SIRCS IN)
PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM ···························· 4-65
· SE-94 (MF DIAL), LB-60 (BACK LIGHT DRIVE)
PRINTED WIRING BOARDS ····················· 4-70
· LB-60 (BACK LIGHT DRIVE)
SCHEMATIC DIAGRAM ···························· 4-73
· FP-90 (BRT, VOL CONTROL),
PD-110 (RGB DECODER, LCD,
TIMING GENERATOR)
PRINTED WIRING BOARDS ····················· 4-77
· FP-90 (BRT, VOL CONTROL),
PD-110 (RGB DECODER, LCD)(1/2)
SCHEMATIC DIAGRAMS ·························· 4-79
· PD-110 (TIMING GENERATOR)(2/2)
SCHEMATIC DIAGRAMS ·························· 4-82
· FP-85 (VTR CONTROL SWITCH BLOCK),
PS4550 (S/S SWITCH)
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ·························· 4-85
· DD-123 (COLOR EVF, DC/DC CONVERTER)
PRINTED WIRING BOARD ······················· 4-88
· DD-123 (COLOR EVF)(1/2)
SCHEMATIC DIAGRAM ··························· 4-91
· DD-123 (DC/DC CONVERTER)(2/2)
SCHEMATIC DIAGRAM ··························· 4-95
5.
ADJUSTMENTS
1.
Before starting adjustment ··············································· 5-1
1-1.
Adjusting items when replacing main parts and boards. · 5-2
5-1.
CAMERA SECTION ADJUSTMENT ··························· 5-4
1-1.
PREPARATIONS BEFORE ADJUSTMENT
(CAMERA SECTION) ··················································· 5-4
1-1-1. List of Service Tools ························································ 5-4
1-1-2. Preparations ····································································· 5-5
1-1-3. Precaution ········································································ 5-7
1.
Setting the Switch ···························································· 5-7
2.
Order of Adjustments ······················································ 5-7
3.
Subjects ··········································································· 5-7
1-2.
INITIALIZATION OF B, C, D, E, F PAGE DATA ········ 5-8
1-2-1. INITIALIZATION OF C PAGE DATA ··························· 5-8
1.
Initializing the C Page Data ············································· 5-8
2.
Modification of C Page Data ··········································· 5-8
3.
C Page Table ···································································· 5-8
1-2-2. INITIALIZATION OF D PAGE DATA ························ 5-10
1.
Initializing the D Page Data ·········································· 5-10
2.
Modification of D Page Data ········································· 5-10
3.
D Page Table ·································································· 5-11
1-2-3. INITIALIZATION OF B PAGE DATA ························· 5-12
1.
Initializing the B Page Data ··········································· 5-12
2.
Modification of B Page Data ········································· 5-12
3.
B Page Table ·································································· 5-13
1-2-4. INITIALIZATION OF E, F PAGE DATA ····················· 5-14
1.
Initializing the E, F Page Data ······································· 5-14
2.
Modification of E, F Page Data ····································· 5-14
3.
F Page Table ·································································· 5-15
4.
E Page Table ·································································· 5-17
1-3.
CAMERA SYSTEM ADJUSTMENTS ························ 5-19
1.
36 MHz Origin Oscillation Adjustment
(VC-217 board) ····························································· 5-19
2.
Zoom Key Center Adjustment ······································· 5-19
3.
HALL Adjustment ························································· 5-19
4.
Flange Back Adjustment (Using Minipattern Box) ······· 5-20
5.
Flange Back Adjustment
(Using Flange Back Adjustment Chart and Subject More
Than 500m Away) ························································· 5-21
5-1.
Flange Back Adjustment(1) ··········································· 5-21
5-2.
Flange Back Adjustment (2) ·········································· 5-21
6.
Flange Back Check ························································ 5-22
7.
Optical Axis Adjustment ··············································· 5-23
8.
Picture Frame Setting ···················································· 5-24
9.
AGC GAIN Calibration Adjustment ····························· 5-24
10.
Color Reproduction Adjustment ···································· 5-25
11.
MAX GAIN Adjustment ··············································· 5-25
12.
Auto White Balance & LV Standard Data Input ··········· 5-26
13.
Auto White Balance Adjustment ··································· 5-26
14.
White Balance Check ···················································· 5-27
15.
Angular Velocity Sensor Sensitivity Adjustment ·········· 5-27
1-4.
COLOR ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENT ····························································· 5-28
1.
VCO Adjustment (DD-123 board) ································ 5-28
2.
Bright Adjustment (DD-123 board) ······························ 5-29
3.
Contrast Adjustment (DD-123 board) ··························· 5-29
4.
Backlight Consumption Current Adjustment
(DD-123 board) ····························································· 5-30
5.
White Balance Adjustment (DD-123 board) ················· 5-30
1-5.
LCD SYSTEM ADJUSTMENT ··································· 5-31
1.
VCO Adjustment (PD-110 board) ································· 5-31
2.
D range Adjustment (PD-110 board) ····························· 5-32
3.
Bright Adjustment (PD-110 board) ······························· 5-32
4.
Contrast Adjustment (PD-110 board) ···························· 5-33
5.
V-COM Level Adjustment (PD-110 board) ·················· 5-33
6.
V-COM Adjustment (PD-110 board) ···························· 5-34
7.
White Balance Adjustment (PD-110 board) ·················· 5-34
5-2.
MECHANISM SECTION ADJUSTMENT ·················· 5-35
2-1.
HOW TO ENTER RECORD MODE
WITHOUT CASSETTE ················································ 5-35
2-2.
HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE ··································································· 5-35
2-3.
TAPE PATH ADJUSTMENT ········································ 5-35
1.
Preparation for Adjustment ··········································· 5-35
2.
Procedure after operations ············································· 5-35
5-3.
VIDEO SECTION ADJUSTMENTS ··························· 5-36
3-1.
PREPARATIONS BEFORE ADJUSTMENTS ············ 5-36


background image
-- 5 --
3-1-1. Equipment Required ····················································· 5-36
3-1-2. Precautions on Adjusting ·············································· 5-37
3-1-3. Adjusting Connectors ···················································· 5-38
3-1-4. Connecting the Equipment ············································ 5-38
3-1-5. Checking the Input Signals
(Except AEP/UK model) ·············································· 5-38
3-1-6. Alignment Tapes ··························································· 5-39
3-1-7. Input/Output Level and Impedance ······························ 5-39
3-2.
SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-40
1.
Initialization of B, C, D, E, F Page Data ······················· 5-40
2.
Battery End Check (VC-217 board) ······························ 5-40
3-3.
SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-41
1.
Cap FG Duty Adjustment (VC-217 board) ··················· 5-41
2.
T reel FG Duty Adjustment (VC-217 board) ················ 5-41
3.
PLL f0 & LPF f0 Adjustment (VC-217 board) ··············· 5-41
4.
Switching Position Adjustment (VC-217 board) ··········· 5-42
5.
AGC Center Level and APC & AEQ Adjustment ········· 5-42
5-1.
Preparations before adjustments ···································· 5-42
5-2.
AGC Center Level Adjustment (VC-217 board) ··········· 5-42
5-3.
APC & AEQ Adjustment (VC-217 board) ···················· 5-43
5-4.
Processing after Completing Adjustments ···················· 5-43
6.
PLL f0 & LPF f0 Final Adjustment (VC-217 board) ····· 5-43
3-4.
VIDEO SYSTEM ADJUSTMENTS ····························· 5-44
3-4-1. Base Band Block Adjustments ······································ 5-44
1.
Chroma BPF fo Adjustment (VC-217 board) ················ 5-44
2.
S VIDEO OUT Y Level Adjustment (VC-217 board) ··· 5-44
3.
S VIDEO OUT Chroma Level Adjustment
(VC-217 board) ····························································· 5-45
4.
AV OUT Y, Chroma Level Check (VC-217 board) ······· 5-45
5.
PLL Adjustment (VC-217 board)
(Except AEP/UK model) ··············································· 5-46
3-4-2. BIST Check ·································································· 5-47
1.
Playback System Check ················································ 5-47
1-1.
Preparation for Playback ··············································· 5-47
1-2.
IC1900 (TRX) BIST (PB) Check ·································· 5-47
1-3.
IC1601 (TFD) BIST (PB) Check ·································· 5-47
1-4.
IC1600 (SFD) BIST (PB) Check ··································· 5-47
1-5.
IC1501 (VFD) BIST (PB) Check ·································· 5-48
2.
Recording System Check ·············································· 5-49
2-1.
Preparations for recording ············································· 5-49
2-2.
IC1501 (VFD) BIST (REC) Check ······························· 5-49
2-3.
IC1600 (SFD) BIST (REC) Check ································ 5-49
2-4.
IC1601 (TFD) BIST (REC) Check ······························· 5-50
2-5.
IC1900 (TRX) BIST (REC) Check ······························· 5-50
3-5.
IR TRANSMITTER ADJUSTMENTS ························· 5-51
1.
IR Video Carrier Frequency Adjustment
(CK-84 board) ······························································· 5-51
2.
IR Video Deviation Adjustment (CK-84 board) ············ 5-51
3.
IR Audio Deviation Adjustment (CK-84 board) ··········· 5-52
3-6.
AUDIO SYSTEM ADJUSTMENTS ···························· 5-53
1.
Playback Level Check ··················································· 5-54
2.
Overall Level Characteristics Check ····························· 5-54
3.
Overall Distortion Check ··············································· 5-54
4.
Overall Noise Level Check ············································ 5-54
5.
Overall Separation Check ·············································· 5-54
5-4.
SERVICE MODE ·························································· 5-55
4-1.
ADJUSTMENT REMOTE COMMANDER ················ 5-55
1.
Using the adjustment remote commander ····················· 5-55
2.
Precautions upon using
the adjustment remote commander ································ 5-55
4-2.
DATA PROCESS ··························································· 5-56
4-3.
SERVICE MODE ·························································· 5-57
1.
Setting the Test Mode ···················································· 5-57
2.
Emergence Memory Address ········································ 5-57
2-1.
EMG Code (Emergency Code) ····································· 5-57
2-2.
MSW Code ···································································· 5-58
3.
Bit value discrimination ················································ 5-59
4.
Switch check (1) ···························································· 5-59
5.
Switch check (2) ···························································· 5-60
6.
Record of Use check ······················································ 5-60
6.
REPAIR PARTS LIST
6-1.
EXPLODED VIEWS ······················································ 6-1
6-1-1. FRONT PANEL SECTION ············································· 6-1
6-1-2. CABINET (R) SECTION ··············································· 6-2
6-1-3. LCD PANEL SECTION ·················································· 6-3
6-1-4. CHASSIS SECTION ······················································· 6-4
6-1-5. CABINET (L) SECTION ················································ 6-5
6-1-6. EVF AND LENS SECTION ··········································· 6-6
6-1-7. CASSETTE COMPARTMENT AND
DRUM ASSY SECTION ················································ 6-7
6-1-8. LS CHASSIS BLOCK SECTION ·································· 6-8
6-1-9. MECHANISM CHASSIS BLOCK SECTION-1 ··········· 6-9
6-1-10. MECHANISM CHASSIS BLOCK SECTION-2 ······· 6-10
6-2.
ELECTRICAL PARTS LIST ········································ 6-11
* The optical axis frame and color reproduction frame is shown
on page 264 and 265.