background image
1
Ver. 1.3 2005. 11
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-611TA-186//K
Optical Pick-up Name
KSS1000E
SERVICE MANUAL
US Model
CDX-S2210/SW330
Canadian Model
CDX-S2210
E Model
CDX-S2210S/S2210X
East European Model
CDX-S2250EE
CDX-S2210/S2210S/S2210X/
S2250EE/SW330
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 ­ 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
US, Canadian Model:
87.5 ­ 107.9 MHz
E model:
FM tuning interval:
50 kHz/200 kHz
switchable
87.5 ­ 108 MHz (at 50 kHz step)
87.5 ­ 107.9 MHz (at 200 kHz step)
East European Model:
FM1/FM2: 87.5 ­ 108.0 MHz (at 50 kHz step)
FM3: 65 ­ 74 MHz (at 30 kHz step)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 ­ 15,000 Hz
SPECIFICATIONS
AM
Tuning range
US, Canadian Model:
530 ­ 1,710 kHz
E Model:
AM tuning interval:
9 kHz/10 kHz switchable
531 ­ 1,602 kHz (at 9 kHz step)
530 ­ 1,710 kHz (at 10 kHz step)
East European Model:
531 ­ 1,602 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30
µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 ­ 8 ohms
Maximum power output Except East European model:
52 W
× 4 (at 4 ohms)
East European model:
50 W
× 4 (at 4 ohms)
General
Outputs
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Inputs
Antenna input terminal
Remote controller input terminal (CDX-S2210C only)
· The tuner and CD sections have no adjustments.
Sony Corporation
eVehicle Division
Published by Sony Engineering Corporation
9-879-323-04
2005K04-1
© 2005. 11
­ Continued on next page ­
FM/AM COMPACT DISC PLAYER
Photo: CDX-S2250EE


background image
2
CDX-S2210/S2210S/S2210X/S2250EE/SW330
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Tone controls
Low:
±10 dB at 60 Hz (XPLOD)
Mid:
±10 dB at 1 kHz (XPLOD)
High:
±10 dB at 10 kHz (XPLOD)
Power requirements
12 V DC car battery
(negative ground)
Dimensions
Approx. 178
× 50 × 178 mm
(7 1/8
× 2 × 7 1/8 in.) (w/h/d)
Mounting dimensions
Approx. 182
× 53 × 161 mm
(7 1/4
× 2 1/8 × 6 3/8 in.) (w/h/d)
Mass
Approx. 1.2 kg
(2 lb. 10 oz.)
Supplied accessories
Card remote commander: RM-X151 (CDX-S2210S/SW330
only) Parts for installation and connections (1 set)
Front panel case (1)
Design and specifications are subject to change without
notice.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
SERVICE NOTES
· E, East European Model
This label is located on the bottom of the chassis.
optical pick-up
semi-fixed resistor


background image
3
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CDX-S2210/S2210S/S2210X/S2250EE/SW330
· CD Playback:
You can play CD-DA (also containing CD TEXT*1), CD-R/CD-
RW (MP3 files also containing Multi Session and ATRAC CD
(ATRAC3 and ATRAC3plus format).
Type of discs
Label on the disc
CD-DA
MP3
ATRAC CD
*1 A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
· Connect the MAIN board (CNP301) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
SERVO BOARD
CN2
MAIN BOARD
CNP301
J-2502-076-1


background image
4
CDX-S2210/S2210S/S2210X/S2250EE/SW330
TABLE OF CONTENTS
1. GENERAL
Location of controls and basic operations (CDX-S2210) ....... 5
Location of controls and basic operations (CDX-S2250EE) .. 5
Location of controls and basic operations
(CDX-S2210S/S2210X) .......................................................... 5
Location of controls and basic operations (CDX-SW330) ..... 6
Connections (CDX-S2210) ..................................................... 7
Connections (CDX-S2210S/S2210X) ..................................... 8
Connections (CDX-S2250EE) ................................................ 9
Connections (CDX-SW330) .................................................. 10
2. DISASSEMBLY
2-1. Sub Panel (LCD) Assy ...................................................... 11
2-2. CD Mechanism Block ....................................................... 12
2-3. Main Board ....................................................................... 12
2-4. Chassis (T) Sub Assy ........................................................ 13
2-5. Roller Arm Assy ................................................................ 13
2-6. Chassis (OP) Assy ............................................................. 14
2-7. Optical Pick-up ................................................................. 14
2-8. SL Motor Assy (M902) ..................................................... 15
2-9. LE Motor Assy (M903) ..................................................... 15
2-10. Servo Board ....................................................................... 16
3. DIAGRAMS
3-1. Block Diagram ­CD Section­ ........................................... 17
3-2. Block Diagram ­Main Section­ ........................................ 18
3-3. Block Diagram ­Display Section­ .................................... 19
3-4. Printed Wiring Boards ­SERVO Board­ .......................... 21
3-5. Schematic Diagram ­SERVO Board (1/2)­ ...................... 22
3-6. Schematic Diagram ­SERVO Board (2/2)­ ...................... 23
3-7. Printed Wiring Board ­Main Board­ ................................ 24
3-8. Schematic Diagram ­Main Board (1/4)­ .......................... 25
3-9. Schematic Diagram ­Main Board (2/4)­ .......................... 26
3-10. Schematic Diagram ­Main Board (3/4)­ .......................... 27
3-11. Schematic Diagram ­Main Board (4/4)­ .......................... 28
3-12. Printed Wiring Board ­KEY Board­ ................................ 29
3-13. Schematic Diagram ­KEY Board­ ................................... 30
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 39
4-2. Front Panel Section ........................................................... 40
4-3. CD Mechanism Section (1) (MG-611TA-186//K) ............ 41
4-4. CD Mechanism Section (2) (MG-611TA-186//K) ............ 42
4-5. CD Mechanism Section (3) (MG-611TA-186//K) ............ 43
4-6. CD Mechanism Section (4) (MG-611TA-186//K) ............ 44
5. ELECTRICAL PARTS LIST ......................................... 45


background image
5
CDX-S2210/S2210S/S2210X/S2250EE/SW330
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
a Volume +/­ button
To adjust volume.
b SEL (select) button 4, 7
To select items.
c SOURCE button
To power on/change the source (Radio/CD).
d MODE button 6
To select the radio band (FM/AM).
e Disc slot
Insert the disc (label side up), playback
starts.
f Display window
g ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
h EQ3 (equalizer) button 7
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
i Z (eject) button
To eject the disc.
j SEEK +/­ button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
k
(front panel release) button 4
l DSPL (display)/DIM (dimmer) button
4
To change display items (press); change the
display brightness (press and hold).
m SENS button
To improve weak reception: LOCAL/
MONO.
n RESET button (located behind the front
panel) 4
o Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD:
(1)/(2): GROUP* ­/+
To skip groups (press); skip groups
continuously (press and hold).
(3): REP 6
(4): SHUF 6
p BTM button 6
To start the BTM function (press and hold).
q OFF button
To power off/stop the source.
r Receptor for the card remote
commander 8
* When an MP3/ATRAC CD is played.
SENS
BTM
OFF
DSPL
1
2
3
4
5
6
SEL
DIM
SHUF
REP
EQ3
ATT
SOURCE MODE
SEEK
CDX-S2250EE
­
+
GROUP
qa
12 3 4
5
6
7 8 9
0
qs qd
qg
qh qj
qk
qf
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
a Volume +/­ button
To adjust volume.
b SEL (select) button 4, 7
To select items.
c SOURCE button
To power on/change the source (Radio/CD).
d MODE button 6
To select the radio band (FM/AM).
e Disc slot
Insert the disc (label side up), playback
starts.
f Display window
g ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
h EQ3 (equalizer) button 7
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
i Z (eject) button
To eject the disc.
j SEEK +/­ button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
k
(front panel release) button 4
l DSPL (display)/DIM (dimmer) button
4, 6
To change display items (press); change the
display brightness (press and hold).
m SENS button
To improve weak reception: LOCAL/
MONO.
n RESET button (located behind the front
panel) 4
o Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD:
(1)/(2): GROUP* ­/+
To skip groups (press); skip groups
continuously (press and hold).
(3): REP 6
(4): SHUF 6
p BTM button 6
To start the BTM function (press and hold).
q OFF button
To power off/stop the source.
r Receptor for the card remote
commander 8
* When an MP3/ATRAC CD is played.
SENS
BTM
OFF
DSPL
1
2
3
4
5
6
SEL
DIM
SHUF
REP
EQ3
ATT
SOURCE MODE
SEEK
CDX-S2210
­
+
GROUP
qa
12 3 4
5
6
7 8 9
0
qs qd
qg
qh qj
qk
qf
Location of controls and basic operations
Main unit
Card remote commander RM-X151
(CDX-S2210S only)
)
SENS
BTM
OFF
DSPL
1
2
3
4
5
6
SEL
DIM
SHUF
REP
EQ3
ATT
SOURCE MODE
SEEK
CDX-S2210X
CDX-S2210S
CDX-S2210C
­
+
GROUP
qa
12 3 4
5
6
7 8 9
0
qs qd
qg
qh
qj qk
qf
ql
SENS
BTM
OFF
DSPL
1
2
3
4
5
6
SEL
DIM
SHUF
REP
EQ3
ATT
SOURCE MODE
SEEK
CDX-S2210X
CDX-S2210S
CDX-S2210C
­
+
GROUP
qa
12 3 4
5
6
7 8 9
0
qs qd
qg
qh
qj qk
qf
ql
OFF
DSPL
SCRL
SEL
SOURCE
MODE
13
2
46
5
ATT
VOL
+
­
+
­
7
qs
qk
3
4
2
wd
w;
wa
wf
ws
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
a Volume +/­ button
To adjust volume.
b SEL (select) button 4, 9
To select items.
c SOURCE button
To power on/change the source (Radio/CD).
d MODE button 8
To select the radio band (FM/AM).
e Disc slot
Insert the disc (label side up), playback
starts.
f Display window
g ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
h EQ3 (equalizer) button 9
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
i Z (eject) button
To eject the disc.
j SEEK +/­ button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
k
(front panel release) button 4
l DSPL (display)/DIM (dimmer) button
4, 8
To change display items (press); change the
display brightness (press and hold).
m SENS button
To improve weak reception: LOCAL/
MONO.
n RESET button (located behind the front
panel) 4
o Frequency select switch (located on the
bottom of the unit)
See "Frequency select switch" in the
supplied installation/connections manual.
p Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD:
(1)/(2): GROUP* ­/+
To skip groups (press); skip groups
continuously (press and hold).
(3): REP 8
(4): SHUF 8
q BTM button 8
To start the BTM function (press and hold).
r OFF button
To power off/stop the source.
s Receptor for the card remote
commander 10
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
t < (.)/, (>) buttons
To control radio/CD, the same as (SEEK)
+/­ on the unit. (For details of other
operations, see "With the card remote
commander" on each pages.)
u VOL +/­ button
To adjust volume.
v M (+)/m (­) buttons
To control CD, the same as (1)/(2) ­/+ on
the unit. (For details of other operations, see
"With the card remote commander" on each
pages.)
w SCRL button
To scroll the display item.
x Number buttons
To receive stored stations (press); store
stations (press and hold).
* When an MP3/ATRAC CD is played.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
"Replacing the lithium battery of the card remote
commander" on page 13.
SECTION 1
GENERAL
This section is extracted
from instruction manual.
(CDX-S2210)
(CDX-S2250EE)
(CDX-S2210S/S2210X)