1
Ver. 1.0 2005. 09
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-611XE-186//C
Optical Pick-up Name
KSS1000E
SERVICE MANUAL
US Model
Canadian Model
CDX-GT10W/GT100
E Model
CDX-GT150/GT150S
CDX-GT10W/GT100/
GT150/GT150S
CD Player section
Signal-to-noise ratio:
120 dB
Frequency response:
10 20,000 Hz
Wow and flutter:
Below measurable limit
Tuner section
FM
Tuning range (CDX-GT10W/GT100):
87.5 107.9 MHz
Tuning range (CDX-GT150/GT150S):
87.5 108.0 MHz (at 50 kHz step)
87.5 107.9 MHz (at 200 kHz step)
FM tuning interval (CDX-GT150/GT150S):
50 kHz/200 kHz switchable
Antenna terminal:
External antenna connector
Intermediate frequency:
10.7 MHz/450 kHz
Usable sensitivity:
9 dBf
Selectivity:
75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation:
35 dB at 1 kHz
Frequency response:
30 15,000 Hz
AM
Tuning range (CDX-GT10W/GT100):
530 1,710 kHz
Tuning range (CDX-GT150/GT150S):
531 1,602 kHz (at 9 kHz step)
530 1,710 kHz (at 10 kHz step)
Antenna terminal:
External antenna connector
Intermediate frequency:
10.7 MHz/450 kHz
Sensitivity:
30 µV
SPECIFICATIONS
Power amplifier section
Outputs:
Speaker outputs (sure seal connectors)
Speaker impedance:
4 8 ohms
Maximum power output: 52 W
× 4 (at 4 ohms) (CDX-GT10/GT100/GT150)
45 W
× 4 (at 4 ohms) (CDX-GT150S)
General
Outputs:
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Inputs:
Antenna input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements:
12 V DC car battery (negative ground)
Dimensions:
Approx. 178
× 50 × 179 mm
(7 1/8
× 2 × 7 1/8 in) (w/h/d)
Mounting dimensions:
Approx. 182
× 53 × 161 mm
(7 1/4
× 2 1/8 × 6 3/8 in) (w/h/d)
Mass:
Approx. 1.2 kg (2 lb 11 oz)
Supplied accessories:
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
· The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Group
Published by Sony Engineering Corporation
9-879-863-01
2005I04-1
© 2005. 09
FM/AM COMPACT DISC PLAYER
(Photo: CDX-GT100)
AUDIO POWER SPECIFICATIONS (US, Canadian model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
2
CDX-GT10W/GT100/GT150/GT150S
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
·Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SERVICE NOTES
This label is located on the bottom of the chassis.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
optical pick-up
semi-fixed resistor
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior. (CDX-GT150/GT150S)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
3
CDX-GT10W/GT100/GT150/GT150S
Notes on CD-DA/CD-R/CD-RW
· CD playback:
You can play CD-DA and CD-R/CD-RW for audio use.
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SERVO BOARD
CN1
MAIN BOARD
CNP301
J-2502-076-1
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
· Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
4
CDX-GT10W/GT100/GT150/GT150S
TABLE OF CONTENTS
1. GENERAL
Location of controls and basic operations ............................... 5
Connections ............................................................................. 6
2. DISASSEMBLY
2-1. Sub Panel Assy .................................................................... 8
2-2. CD Mechanism Block ......................................................... 8
2-3. Main Board ......................................................................... 9
2-4. Chassis (T) Sub Assy .......................................................... 9
2-5. Roller Arm Assy ................................................................ 10
2-6. Chassis (OP) Assy ............................................................. 10
2-7. Optical Pick-up ................................................................. 11
2-8. SL Motor Assy (M902) ..................................................... 11
2-9. LE Motor Assy (M903) ..................................................... 12
2-10. Servo Board ....................................................................... 12
3. DIAGRAMS
3-1. Block Diagram CD Section ......................................... 13
3-2. Block Diagram Main Section ...................................... 14
3-3. Block Diagram Display Section .................................. 15
3-4. Circuit Boards Location .................................................... 15
3-5. Printed Wiring Boards CD Mechanism Section ......... 16
3-6. Schematic Diagram CD Mechanism Section .............. 17
3-7. Printed Wiring Board Main Section ............................ 18
3-8. Schematic Diagram Main Section (1/3) ...................... 19
3-9. Schematic Diagram Main Section (2/3) ...................... 20
3-10. Schematic Diagram Main Section (3/3) ...................... 21
3-11. Printed Wiring Boards Key Section ............................ 22
3-12. Schematic Diagram Key Section ................................ 23
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 31
4-2. Front Panel Section ........................................................... 32
4-3. CD Mechanism Section (1) (MG-611XE-186//C) ............ 33
4-4. CD Mechanism Section (2) (MG-611XE-186//C) ............ 34
4-5. CD Mechanism Section (3) (MG-611XE-186//C) ............ 35
4-6. CD Mechanism Section (4) (MG-611XE-186//C) ............ 36
5. ELECTRICAL PARTS LIST ........................................ 37
5
CDX-GT10W/GT100/GT150/GT150S
SECTION 1
GENERAL
This section is extracted
from instruction manual.
· CDX-GT10W/GT100
· CDX-GT150/GT150S
5
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
A OFF button
To power off; stop the source.
B Volume control dial/select button 6
To adjust volume (rotate); select setup items
(press and rotate).
C EQ3 (equalizer) button 6
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
D Disc slot
To insert the disc (label side up), playback
starts.
E Display window
F Z (eject) button
To eject the disc.
G DSPL (display)/DIM (dimmer) button
4
To change display items (press); change the
display brightness (press and hold).
H
(front panel release) button 4
I SEEK /+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
J SOURCE button
To power on; change the source (Radio/CD/
AUX).
K BTM button 6
To start the BTM function (press and hold).
L MODE button 6
To select the radio band (FM/AM).
M RESET button (located behind the front
panel) 4
N Number buttons
CD:
(3): REP
To play the current track repeatedly.
(4): SHUF
To play the tracks in random order.
Radio:
To receive stored stations (press); store
stations (press and hold).
O SENS button
To improve weak reception: LOCAL/
MONO.
P AUX input jack 7
To connect a portable audio device.
CDX-GT100
CDX-GT10W
5
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
A OFF button
To power off; stop the source.
B Volume control dial/select button 6
To adjust volume (rotate); select setup items
(press and rotate).
C EQ3 (equalizer) button 6
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF).
D Disc slot
To insert the disc (label side up), playback
starts.
E Display window
F Z (eject) button
To eject the disc.
G DSPL (display)/DIM (dimmer) button
4
To change display items (press); change the
display brightness (press and hold).
H
(front panel release) button 4
I SEEK /+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
J SOURCE button
To power on; change the source (Radio/CD/
AUX).
K BTM button 6
To start the BTM function (press and hold).
L MODE button 6
To select the radio band (FM/AM).
M RESET button (located behind the front
panel) 4
N Frequency select switch (located on
the bottom of the unit)
See "Frequency Select switch" in the
supplied installation/connections manual.
O Number buttons
CD:
(3): REP
To play the current track repeatedly.
(4): SHUF
To play the tracks in random order.
Radio:
To receive stored stations (press); store
stations (press and hold).
P SENS button
To improve weak reception: LOCAL/
MONO.
Q AUX input jack 7
To connect a portable audio device.
CDX-GT150S
CDX-GT150