background image
1
Ver 1.0 2003. 12
Model Name Using Similar Mechanism
CDX-S2000/SW200
CD Drive Mechanism Type
MG-611XA-186//K
Optical Pick-up Name
KSS1000E
SERVICE MANUAL
US Model
CDX-F7000/F7005X/FW700
Canadian Model
CDX-F7000/F7005X
CDX-F7000/F7005X/FW700
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 ­ 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 ­ 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 ­ 15,000 Hz
AM
Tuning range
530 ­ 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 ­ 8 ohms
Maximum power output 52 W
× 4 (at 4 ohms)
SPECIFICATIONS
General
Outputs
Audio output terminals (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Inputs
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input or AUX IN terminal
Remote controller input terminal
Antenna input terminal
Tone controls
Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
Loudness
+8 dB at 100 Hz
+2 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
Dimensions
Approx. 178
× 50 × 178 mm
(7 1/8
× 2 × 7 1/8 in.) (w/h/d)
Mounting dimensions
Approx. 182
× 53 × 161 mm
(7 1/4
× 2 1/8 × 6 3/8 in.) (w/h/d)
Mass
Approx. 1.3 kg (2 lb. 14 oz.)
Supplied accessories
Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X118A
Design and specifications are subject to change without
notice.
· The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-961-473-01
2003L04-1
© 2003. 12
FM/AM COMPACT DISC PLAYER


background image
2
CDX-F7000/F7005X/FW700
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SERVICE NOTES
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
Notes on CD-R/CD-RW discs
·You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
· Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
·You cannot play a CD-R/a CD-RW that is not finalized*.
*A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
optical pick-up
semi-fixed resistor


background image
3
CDX-F7000/F7005X/FW700
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
· Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
SERVO BOARD
CN1
MAIN BOARD
CNP301
J-2502-076-1


background image
4
CDX-F7000/F7005X/FW700
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 5
Connections (CDX-F7000/F7005X) ....................................... 6
Connections (CDX-FW700) .................................................... 7
2. DISASSEMBLY
2-1. Sub Panel Assy (CD) ........................................................... 9
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ....................................................................... 10
2-4. Chassis (T) Sub Assy ........................................................ 10
2-5. Roller Arm Assy ................................................................ 11
2-6. Chassis (OP) Assy ............................................................. 11
2-7. Optical Pick-up ................................................................. 12
2-8. SL Motor Assy (M902) ..................................................... 12
2-9. LE Motor Assy (M903) ..................................................... 13
2-10. Servo Board ....................................................................... 13
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 14
3-2. Block Diagram ­CD Section­ ........................................... 19
3-3. Block Diagram ­Main Section­ ........................................ 20
3-4. Block Diagram ­Display Section­ .................................... 21
3-5. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................... 22
3-6. Waveforms ......................................................................... 22
3-7. Circuit Boards Location .................................................... 22
3-8. Printed Wiring Boards ­CD Mechanism Section­ ............ 23
3-9. Schematic Diagram ­CD Mechanism Section­ ................ 24
3-10. Schematic Diagram ­Main Section (1/3)­ ........................ 25
3-11. Schematic Diagram ­Main Section (2/3)­ ........................ 26
3-12. Schematic Diagram ­Main Section (3/3)­ ........................ 27
3-13. Printed Wiring Boards ­Main Section­ ............................ 28
3-14. Printed Wiring Board ­Sub Section­ ................................ 30
3-15. Schematic Diagram ­Sub Section­ ................................... 31
3-16. Printed Wiring Board ­Key Section­ ................................ 32
3-17. Schematic Diagram ­Key Section­ ................................... 33
3-18. IC Block Diagrams ............................................................ 34
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 36
4-2. Front Panel Section ........................................................... 37
4-3. CD Mechanism Section (1) ............................................... 38
4-4. CD Mechanism Section (2) ............................................... 39
4-5. CD Mechanism Section (3) ............................................... 40
4-6. CD Mechanism Section (4) ............................................... 41
5. ELECTRICAL PARTS LIST ......................................... 42


background image
5
CDX-F7000/F7005X/FW700
4
Location of controls
Refer to the pages listed for details.
a DSPL (display mode change) button
12, 14, 21
b Number buttons
Radio:
To store stations/receive stored stations.
CD/MD:
(1): REP 13
(2): SHUF 13
c DSO button 23
d MENU button
To display the menus.
e SOURCE (Power on/Radio/CD/MD*1/
AUX*2) button
To select the source.
f SEEK/AMS (</,) buttons
To skip tracks/fast-forward, reverse a track/
tune in stations automatically, find a station
manually/select a setting.
g SOUND button 20
h OFF (Stop/Power off) button 11, 24
i VOL (+/­) buttons
To turn up or down the volume.
j EQ7 button 22
Card remote commander RM-X118A
DISC ­
ATT
OFF
REP
PTY
SHUF
DSPL
1
4
MODE
2
5
3
6
SOURCE
DISC +
SEEK+
SEEK­
SOUND
ENTER
MENU
LIST
CAT
EQ7
DSO
VOL
DISC ­
SOURCE
DISC +
SEEK+
SEEK­
In menu mode, the currently selectable button(s) of
these four are indicated with a " v" in the display.
(SEEK) (<):
to select
leftwards
(DISC) (M):
to select upwards
(DISC) (m):
to select downwards
(SEEK) (,):
to select
rightwards
SECTION 1
GENERAL
This section is extracted
from instruction manual.
5
k MODE button
To change operation.
l LIST (CAT)*3 button 15, 18
m DISC (ALBUM) (M/m) buttons
To receive preset stations/change the disc*4,
skip albums*5/select a menu.
n ENTER button
To enter a setting.
o ATT button 20
*1 When an optional MD unit is connected.
*2 Available only when an optional Sony portable
device is connected to AUX IN terminal of the unit.
When you connect a Sony portable device and CD/
MD unit(s) at the same time, use the AUX IN
selector.
*3 The CAT button is available only when the XM
tuner is connected.
*4 When an optional CD/MD unit is connected.
*5 Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
Note
If the display disappears by pressing (OFF), it cannot
be operated with the card remote commander unless
(SOURCE)
on the unit is pressed, or a disc is inserted
to activate the unit first.
Tip
For details on how to replace the battery, see
"Replacing the lithium battery" on page 25.
Selecting a disc and album
Disc and album can be skipped using the DISC
(ALBUM) (M/m) buttons.
(With optional unit)
*6 Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
Skipping tracks continuously
Press once either SEEK/AMS (< or ,)
button, then press again within about 1 second
and hold.
To
Press
Skip discs
­Disc selection
M or m [once for each disc]
Skip albums*6
­Album selection
M or m [hold for a moment]
and release.
To continuously skip
albums, press (and hold)
within about 1 second of
first releasing the button.
6
The buttons on the unit share the same
functions as those on the card remote
commander.
a 5 SEEK/AMS (.m/M>)
buttons
b Volume control dial/SOUND button
Rotate to:
­ Adjust the volume.
­ Adjust the sound settings.
Press to:
­ Select the sound items.
3 qs DISC (ALBUM)/PRESET (+/­)
buttons
4 MODE button
6 DSO button
7 SCRL (scroll) button
8 Display window
9 Z (eject) button (located on the front side
of the unit, behind the front panel) 10, 11
0 OPEN button 9, 10, 11
qa Receptor for the card remote
commander
qd OFF (Stop/Power off) button*
qf EQ7 button
qg RESET button (located on the front side of
the unit, behind the front panel) 8
qh SOURCE button
qj Number buttons
qk DSPL (display mode change) button
ql IMAGE button 23
* Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
PUS
H SOUND
DISC/
PRESET
MODE
DISC/
PRESET
SEEK
+
SEEK
­
IMAGE
OFF
DSO
EQ7
SCRL
REP
SHUF
6
OPEN
D
E
SOURCE
DSPL
1
S
25
34
CDX-F7005X/F7000
6
The buttons on the unit share the same
functions as those on the card remote
commander.
a 5 SEEK/AMS (.m/M>)
buttons
b Volume control dial/SOUND button
Rotate to:
­ Adjust the volume.
­ Adjust the sound settings.
Press to:
­ Select the sound items.
3 qs DISC (ALBUM)/PRESET (+/­)
buttons
4 MODE button
6 DSO button
7 SCRL (scroll) button
8 Display window
9 Z (eject) button (located on the front side
of the unit, behind the front panel) 10, 11
0 OPEN button 9, 10, 11
qa Receptor for the card remote
commander
qd OFF (Stop/Power off) button*
qf EQ7 button
qg RESET button (located on the front side of
the unit, behind the front panel) 8
qh SOURCE button
qj Number buttons
qk DSPL (display mode change) button
ql IMAGE button 23
* Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
PUS
H SOUND
DISC/
PRESET
MODE
DISC/
PRESET
SEEK
+
SEEK
­
IMAGE
OFF
DSO
EQ7
SCRL
REP
SHUF
6
OPEN
D
E
SOURCE
DSPL
1
S
25
34
CDX-FW700