background image
1
Ver 1.0 2004. 01
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-611XA-186//Q
Optical Pick-up Name
KSS1000E
SERVICE MANUAL
US Model
Canadian Model
CDX-F5005X
AEP Model
UK Model
CDX-F5000C
CDX-F5000C/F5005X
CD player section
Signal-to-noise ratio
120 dB
Frequency response
10 ­ 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
87.5 ­ 108.0 MHz (F5000C)
87.5 ­ 107.9 MHz (F5005X)
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 ­ 15,000 Hz
MW/LW (CDX-F5000C)
Tuning range
MW: 531 ­ 1,602 kHz
LW: 153 ­ 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV
LW: 40 µV
AM (CDX-F5005X)
Tuning range
530 ­ 1,710 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
AM: 30 µV
SPECIFICATIONS
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 ­ 8 ohms
Maximum power output 50 W
× 4 (at 4 ohms) (CDX-F5000C)
52 W
× 4 (at 4 ohms) (CDX-F5005X)
General
Outputs
Audio outputs terminal
(rear/sub switchable)
Power aerial relay control terminal (F5000C)
Power antenna relay control terminal (F5005X)
Power amplifier control terminal
Inputs
Telephone ATT control terminal
Remote controller input terminal
BUS control input terminal
BUS audio input terminal
Antenna input terminal (F5005X)
Aerial input terminal (F5000C)
Tone controls
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
· The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US, Canadian model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-877-563-01
2004A04-1
© 2004. 01
­ Continued on next page ­
FM/MW/LW COMPACT DISC PLAYER
CDX-F5000C
FM/AM COMPACT DISC PLAYER
CDX-F5005X
Photo: CDX-F5005X


background image
2
CDX-F5000C/F5005X
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
Power requirements
12 V DC car battery
(negative ground)
Dimensions
Approx. 178
× 50 × 181 mm
(w/h/d)
Mounting dimensions
Approx. 182
× 53 × 161 mm
(w/h/d)
Mass
Approx. 1.2 kg
Supplied accessories
Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander (F5005X)
Design and specifications are subject to change without
notice.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SERVICE NOTES
This label is located on the bottom of the chassis.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
Notes on CD-R/CD-RW discs
·You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
· Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
·You cannot play a CD-R/a CD-RW that is not finalized*.
*A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
optical pick-up
semi-fixed resistor
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
· AEP, UK model


background image
3
CDX-F5000C/F5005X
z
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
· Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
· Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
SERVO BOARD
CN1
J-2502-076-1
MAIN BOARD
CNP301


background image
4
CDX-F5000C/F5005X
TABLE OF CONTENTS
1. GENERAL
Location of controls ................................................................. 5
Connections ............................................................................. 6
2. DISASSEMBLY
2-1. Sub Panel Assy .................................................................... 8
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ......................................................................... 9
2-4. Chassis (T) Sub Assy ........................................................ 10
2-5. Roller Arm Assy ................................................................ 10
2-6. Chassis (OP) Assy ............................................................. 11
2-7. Optical Pick-up ................................................................. 11
2-8. SL Motor Assy (M902) ..................................................... 12
2-9. LE Motor Assy (M903) ..................................................... 12
2-10. Servo Board ....................................................................... 13
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 14
3-2. Block Diagram ­CD Section­ ........................................... 19
3-3. Block Diagram ­Tuner Section­ ....................................... 20
3-4. Block Diagram ­Display Section­ .................................... 21
3-5. Circuit Boards Location .................................................... 21
3-6. Printed Wiring Boards ­CD Mechanism Section­ ............ 22
3-7. Schematic Diagram ­CD Mechanism Section­ ................ 23
3-8. Printed Wiring Board ­Main Section­ .............................. 24
3-9. Schematic Diagram ­Main Section (1/2)­ ........................ 25
3-10. Schematic Diagram ­Main Section (2/2)­ ........................ 26
3-11. Printed Wiring Board ­SUB Section­ ............................... 27
3-12. Schematic Diagram ­SUB Section­ ................................. 27
3-13. Printed Wiring Board ­Key Section­ ................................ 28
3-14. Schematic Diagram ­Key Section­ ................................... 29
3-15. IC Block Diagrams ............................................................ 30
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 32
4-2. Front Panel Section ........................................................... 33
4-3. CD Mechanism Section (1) ............................................... 34
4-4. CD Mechanism Section (2) ............................................... 35
4-5. CD Mechanism Section (3) ............................................... 36
4-6. CD Mechanism Section (4) ............................................... 37
5. ELECTRICAL PARTS LIST ........................................ 38


background image
5
CDX-F5000C/F5005X
SECTION 1
GENERAL
This section is extracted
from instruction manual.
(CDX-F5000C)
(CDX-F5005X)