background image
-- 1 --
SPECIFICATIONS
Model Name Using Similar Mechanism
CDP-XE200/XE300
CD Mechanism Type
CDM14-5BD20
Base Unit Type
BU-5BD20
Optical Pick-up Type
KSS-213BA/F-NP
SERVICE MANUAL
AEP Model
UK Model
COMPACT DISC PLAYER
MICROFILM
Photo: CDP-XE310
CDP-XE210/XE310


background image
-- 2 --
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
This caution label is located inside
the unit.
The laser component in this product is ca-
pable of emitting radiation exceeding the
limit for Class 1.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Notes on chip component replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
· Keep the temperature of soldering iron around 270°C
during repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE
WITH MARK
! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS
1. SERVICING NOTE .......................................................... 3
2. GENERAL .......................................................................... 4
3. DISASSEMBLY
3-1. Front Panel ........................................................................... 5
3-2. Base Unit (BU-5BD20) ......................................................... 5
4. TEST MODE ....................................................................... 6
5. ELECTRICAL BLOCK CHECKING .......................... 7
6. DIAGRAMS
6-1. Circuit Boards Location ........................................................ 9
6-2. Printed Wiring Board -- BD Section -- ............................. 11
6-3. Schematic Diagram -- BD Section -- ............................... 13
6-4. Schematic Diagram -- Main Section -- ............................ 15
6-5. Printed Wiring Board -- Main Section -- .......................... 17
6-6. Printed Wiring Board -- Panel Section -- ......................... 19
6-7. Schematic Diagram -- Panel Section -- ............................ 21
6-8. IC Pin Functions
· IC501 CXP82612-021Q (Master Control) ....................... 23
6-9. IC Block Diagrams ............................................................. 24
7. EXPLODED VIEWS
7-1. Main Section ....................................................................... 26
7-2. Mechanism Deck Section (CDM14-5BD20) ...................... 27
7-3. Base Unit Section (BU-5BD20) .......................................... 28
8. ELECTRICAL PARTS LIST ........................................ 29
MODEL IDENTIFICATION
­ BACK PANEL ­
PARTS No.
MODEL
PRODUCT
COUNTRY
XE210: 4-988-712-0
XE210: 4-988-712-1
XE310: 4-988-712-2
XE310: 4-988-712-3
XE210: 4-988-712-4
XE210: 4-979-971-5
XE210: 4-988-712-5
XE210: 4-979-971-6
XE310: 4-988-712-6
XE310: 4-979-971-7
XE310: 4-988-712-7
XE310: 4-979-971-8
AEP, EE, CIS
UK
AEP, EE, CIS
UK
AEP, EE, CIS
AEP, EE, CIS
UK
UK
AEP, EE, CIS
AEP, EE, CIS
UK
UK
FRANCE
FRANCE
FRANCE
FRANCE
HUNGARY
HUNGARY
HUNGARY
HUNGARY
HUNGARY
HUNGARY
HUNGARY
HUNGARY
· Abbreviation
EE
: East European model
Parts No.


background image
-- 3 --
SECTION 1
SERVICING NOTE
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer
electrostatic breakdown because of the potential difference
generated by the charged electrostatic load, etc. on clothing and
the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the "S curve check" in "CD section adjustment" and
check that the S curve waveform is output two times.
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
Insert a tapering driver into the aperture of the unit bottom, and turn
in the direction of arrow.
* To close the disc table, turn the driver in the reverse direction.
Pull out disc table


background image
-- 4 --
SECTION 2
GENERAL
LOCATION OF PARTS AND CONTROLS
Front Panel
!¡ AMS* ± knob
!TM p (stop) button
!£ P (pause) button
!¢ · (play) button
! Display window
!§ MUSIC SCAN button
!¶ PEAK SEARCH button
!· EDIT/TIME FADE button
1 POWER switch
2 PLAY MODE button
3 REPEAT button
4 TIME button
5 Disc tray
6 § OPEN/CLOSE button
7 0/) button
8 CHECK button
9 CLEAR button
!º ENTER button
* AMS is the abbreviation for Automatic Music Sensor.
1
34
25
78 9 0
6
!TM
!


background image
-- 5 --
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. FRONT PANEL
· In order to remove the front panel block when the power supply
does not turn on, rotate the cam with tapering driver as the figure
shows, and the loading part will be moved.
Then pull out the loading part by your hand to remove the load-
ing panel as the figure shows. After that take out the front panel
block.
Tapering driver
Loading part
Loading panel
1 Turn the cam to the direction of ar-
row (counter clock wise)
by tapering driver.
BU-5BD20
2 Take off the disc table.
3 Yoke bracket
4 Remove the Base unit
(BU-5BD20) to the direction
of arrow.
3-2. BASE UNIT (BU-5BD20)