background image
ORDER NO.
SH-D500
DIGITAL TV TUNER
ORDER NO.
ARP3020
O- ZZS FEB. 1999 Printed in Japan
c
PIONEER ELECTRONIC CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER ELECTRONIC CORPORATION 1999
Type
Model
Power Requirement
Remarks
SH-D500
KU
AC120V
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 3
3. SCHEMATIC DIAGRAM ....................................... 8
4. PCB CONNECTION DIAGRAM .......................... 64
5. PCB PARTS LIST ............................................... 74
6. ADJUSTMENT .................................................... 92
CONTENTS
ÙcÙ ÛxXcVcicV ixÇxNccV
Ù¿Û.??
DOLBY
DIGITAL
7. GENERAL INFORMATION ................................ 98
7.1 DIAGNOSIS .................................................. 98
7.1.1 DISASSEMBLY ...................................... 98
7.1.2 PWBS LAYOUT .................................... 102
7.1.3 TROUBLESHOOTING ......................... 103
7.1.4 CHASSIS LAYOUT .............................. 107
7.2 BLOCK DIAGRAM ...................................... 109
8. PANEL FACILITIES AND SPECIFICATIONS .. 110
The service supplied parts are only listed at page 3 and 6.
The parts listed at page 75 to page 91 are not supplied as a
service part.


background image
SH-D500
2
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & safety code section 25249.6--Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse)
and/or
(slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide)
et/ou
(fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE
LIMITS OUTLINED ABOVE ARE INDICATIVE
OF A POTENTIAL SHOCK HAZARD AND
MUST BE CORRECTED BEFORE RETURN-
ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident
from visual
inspection nor the
protection afforded by them necessarily can be obtained
by using replacement components rated for voltage,
wattage, etc. Replacement parts which have these
special safety characteristics are identified in this
Service Manual.
Electrical components having such features are
identified by marking with a
on the schematics and
on the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER
Service Manual. A subscription to, or
additional copies
of, PIONEER Service Manual may be obtained at a
nominal charge from PIONEER.
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
Device
under
test
Leakage
current
tester
Earth
ground
Reading should
not be above
0.5 mA
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
AC Leakage Test


background image
3
SH-D500
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
Infrared R/C Unit
Polystyrene Cover
Buffer Material
(Right and Left)
Using the Operation Manual bag tape,
seal the bag too.
Accessories
Operation Manual
DTV Caution card
Batteries (2pcs.)
BNC-BNC 3C3V Cable
Wrap the AC power cord with the top mirror
foil. Apply the tape onto the bottom mirror foil,
the AC power cord mirror foil and the
Operation Manual bag. (Do not apply the tape
direct on the AC power cord).
The packing case
top is tape sealed.
Packing Case
Bar Code Serial No. Label
Front
ACCESSORIES
RRMCG1489CESA ­ Infrared R/C Unit
--
TiNS-6581CEZZ
­ Operation Manual(English)
--
ARM1158
­ DTV Caution Card
--
NSP
­
­ AA size Batteries, x2
--
NSP
TCAUH3082CEZZ
­ Caution Sheet
--
NSP
RCORF0084CEZZ
­ Ferrite Core
--
NSP
ARY7023
­ Warranty Card
--
NSP
ARY1096
­ Registration Card
--
NSP
ADF1004
­ BNC-BNC 3C3V Cable (5m) --
ACCESSORIES
(NOT REPLACEMENT ITEM)
PACKING PARTS
SPAKC5302CEZZ
­ Packing Case
--
SPAKP0837CEZZ
­ Polystyrene Cover
--
SPAKX2874CEZZ
­ Buffer Material
--
SSAKA0170CEZZ
­ Polyethylene Bag
--
SUPPLIED ACCESSORIES
Ref. No.
Part No.
Description
Code
Ref. No.
Part No.
Description
Code
NOTES:
· Parts marked by "NSP" are generally
unavailable because they are not in our
Master Spare Parts List.
· The mark found on some component
parts indicates the importance of the
safety factor of the part.
Therefore, when replacing, be sure to use
parts of identical designation.
SERVICE JIGS
(Use for servicing)
NSP
QCNW-5142CEZZ
J Extension Cable 7-pin
AL
Sub Power-Power
NSP
QCNW-5143CEZZ
J Extension Cable 5-pin
AG
Sub Power-Power
NSP
QCNW-5144CEZZ
J Extension Cable 6-pin
AL
ATV1-Sub Power
NSP
QCNW-5145CEZZ
J Extension Cable 8-pin
AM
ATV2-Sub Power
NSP
QCNW-5146CEZZ
J Extension Cable 5-pin
AG
ATV1-Sub Power
NSP
QCNW-5147CEZZ
J Extension Cable 3-pin
AF
ATV1-ATV2
NSP
QCNW-5148CEZZ
J Extension Cable 8-pin
AS
ATV1-ATV2


background image
4
SH-D500
39
25
20
1-
1-5
2
2-1
2-2
2-3
2-5
2-7
B
3
4
6
7
10
12
15
16
19
21
51
26
55
26
37
29
31
31
49
45
48
39
40
38
2-4
2-6
2-8
29
A
B
A
58
D
D
2-9
ÙcÙ
ÛxXcVcicV
ixÇxNccV
Ù¿Û.??
DOLBY
DIGITAL
2.2 CABINET AND MECHANICAL PARTS


background image
5
SH-D500
39
1-4
1-1
1-3
1-2
1-6
1-7
1-5
C
C
5
4
9
1
11
17
18
22
42
50
35
22
23
54
51
53
27
28
59
30
60
33
50
43
44
46
34
47
56
36
22
22
22
13
1-3
1-8
A
37
52
58
57