4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8655, Japan
PIONEER ELECTRONICS SERVICE, INC.
P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
© PIONEER CORPORATION 2003
1. SAFETY INFORMATION ............................................. 2
2. DISASSEMBLY ............................................................ 3
3. PACKING, EXPLODED VIEWS AND PARTS LIST ..... 3
4. SCHEMATIC AND PCB CONNECTION DIAGRAMS .. 6
5. PCB CONNECTION DIAGRAM ................................. 10
6. PCB PARTS LIST ...................................................... 13
7. ADJUSTMENT ........................................................... 15
8. PANEL FACILITIES .................................................... 16
9. SPECIFICATIONS ....................................................... 17
HOME THEATER LOUDSPEAKER SYSTEM
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODELS AND TYPES
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-yourselfer. Qualified technicians
have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those
covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not
qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a
qualified service technician.
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth
defects or other reproductive harm.
Health & Safety Code Section 25249.6 Proposition 65
(FOR CANADIAN MODEL ONLY)
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must be of identical
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces de remplacement
doivent avoir la même désignation.
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water pipe,
conduit, etc.) by connecting a leakage current tester such as Simpson
Model 229-2 or equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals, screwheads,
metal overlays, control shaft, etc.). Plug the AC line cord of the
appliance directly into a 120V AC 60Hz outlet and turn the AC power
switch on. Any current measured must not exceed 0.5mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED
ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD
AND MUST BE CORRECTED BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are often
not evident from visual inspection nor the protection afforded
by them necessarily can be obtained by using replacement
components rated for voltage, wattage, etc. Replacement parts
which have these special safety characteristics are identified
in this Service Manual.
Electrical components having such features are identified
by marking with a on the schematics and on the parts list in
this Service Manual. The use of a substitute replacement
component which does not have the same safety characteristics
as the PIONEER recommended replacement one, shown in
the parts list in this Service Manual, may create shock, fire, or
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
(FOR USA MODEL ONLY)
not be above
Also test with
(Using AC adapter
plug as required)
AC Leakage Test
¶ POWER AMP SECTION
Remove the 8 screws from the power amplifier.
Remove the connector lead, etc.
¶ FRONT PANEL
The front panel is attached to the cabinet by its bosses
applied with adhesive.
To detach it, pry it open by inserting a flat blade
screwdriver into bottom slot between the cabinet and front
To detach first remove the front panel, then remove the
4 external screws.
3. PACKING EXPLODED VIEWS AND PARTS LIST
¶ Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
¶ The mark found on some component parts indicates the importance of the safety factor of the part. Therefore,whenreplacing,besure to use parts
of identical designation.
¶ Parts marked by " " are not always kept in stock. Their delivery time may be longer than they may be unavailable.
RCA Pin Cable CEA Purple
Speaker Wire for FR CEA Red 5M
Speaker Wire for FL CEA White 5M
Speaker Wire for C CEA Green 4M
Speaker Wire for RR CEA Grey 8M
Speaker Wire for RL CEA Blue 8M
Speaker Wire for RC CEA Brown 10M
Rubber Foot (A) Set
Rubber Foot (B) Set
Styro Pad Top
Styro Pad Mid
Styro Pad Bottom
Packing Case (730-S/KUXCN)
Speaker Wire + Foot Assy
¶ Satellite Speakers are provided as assembly units.
2-10 & 15
3.2 EXTERIOR SECTION
3.2.1 POWERED SUBWOOFER
Cabinet silver PVC (S)
Amplifier Assy (HTP-A3)
Front Panel silver painted (S)
Port Flare Assy
Logo Badge silver (S)
Screw for woofer + AMP
3.2.2 SATELLITE SPEAKER
Satellite Front Assy (S)
Satellite Center Assy (S)
Satellite Rear Assy (S)
3.3 POWER AMP SECTION
¶ Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List.
mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing,
be sure to use parts of identical designation.
¶ Screw adjacent to mark on the product are used for disassembly.
AC Power Cord
OPERATION ASSY AWU7761
Rear Case Assy
Air Packing L
Air Packing S
Vol Knob Assy
Fuse ( FU 1 ) 5A
Fuse Caution Label ARW7083
ICP 65 Label
7 EXTERIOR SECTION PARTS LIST