background image
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
PDP-R06G
ARP3281
MEDIA RECEIVER
PDP-R06G
PDP-R06C
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
Power Requirement
Remarks
PDP-R06G
TLDFXJ
AC 110V - 240V
PDP-R06C
WAXU5
AC 220V - 240V
For details, refer to "Important Check Points for good servicing".
T-IZR SEPT. 2005 printed in Japan


background image
PDP-R06G
2
12
34
12
3
4
C
D
F
A
B
E
SAFETY INFORMATION
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakage
current tester such as Simpson Model 229-2 or
equivalent between the earth ground and all exposed
metal parts of the appliance (input/output terminals,
screwheads, metal overlays, control shaft, etc.). Plug
the AC line cord of the appliance directly into a 120V
AC 60 Hz outlet and turn the AC power switch on. Any
current measured must not exceed 0.5 mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are
identified by marking with a > on the schematics and on
the parts list in this Service Manual.
The use of a substitute replacement component which
does not have the same safety characteristics as the
PIONEER recommended replacement one, shown in the
parts list in this Service Manual, may create shock, fire,
or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of,
PIONEER Service Manual may be obtained at a nominal
charge from PIONEER.
Leakage
current
tester
Reading should
not be above
0.5 mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
(FOR USA MODEL ONLY)
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.


background image
PDP-R06G
3
56
78
56
7
8
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.


background image
PDP-R06G
4
12
34
12
3
4
C
D
F
A
B
E
CONTENTS
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING SECTION .................................................................................................................................. 6
2.2 EXTERIOR SECTION................................................................................................................................ 8
2.3 FRONT PANEL SECTION ....................................................................................................................... 10
3. BLOCK DIAGRAM .......................................................................................................................................... 12
3.1 OVERALL BLOCK DIAGRAM.................................................................................................................. 12
3.2 POWER SUPPLY UNIT............................................................................................................................ 14
3.3 POWER SUPPLY SIGNAL ROUTE ......................................................................................................... 15
3.4 VOLTAGES ............................................................................................................................................... 16
5. PCB PARTS LIST ........................................................................................................................................... 17
6. ADJUSTMENT ............................................................................................................................................... 23
6.1 POSSIBLE CASES WHERE READJUSTMENT IS REQUIRED ............................................................. 23
6.2 SERVICING USING ONLY THE MEDIA RECEIVER ............................................................................... 24
6.3 SERVICE FACTORY MODE .................................................................................................................... 25
6.4 LIST OF RS-232C COMMANDS ............................................................................................................. 38
6.5 OUTLINE OF COMMANDS ..................................................................................................................... 39
7. GENERAL INFORMATION ............................................................................................................................. 41
7.1 DIAGNOSIS ............................................................................................................................................. 41
7.1.1 TROUBLESHOOTING ....................................................................................................................... 41
7.1.2 DISASSEMBLY.................................................................................................................................. 50
7.2 EXPLANATION ........................................................................................................................................ 51
7.2.1 PROCESSING IN ABNORMALITY ................................................................................................... 51
7.2.2 POWER ON SEQUENCE.................................................................................................................. 54
7.3 PARTS...................................................................................................................................................... 55
7.3.1 IC ....................................................................................................................................................... 55
8. PANEL FACILITIES ........................................................................................................................................ 86


background image
PDP-R06G
5
56
78
56
7
8
C
D
F
A
B
E
1. SPECIFICATIONS
: This conforms to HDMI1.1 and HDCP1.1.
HDMI (High Definition Multimedia Interface) is a digital interface that handles both video and audio using a single cable.
HDCP (High-bandwidth Digital Content Protection) is a technology used to protect copyrighted digital contents that use
the Digital Visual Interface (DVI).
÷ Design and specifications are subject to change without notice.
Accessories
Power cord
(ADG1209: PDP-R06C)
Remote control unit
(AXD1510: PDP-R06G)
(AXD1511: PDP-R06C)
AA size Battery
×2
(VEM1031: PDP-R06G)
(VEM1010: PDP-R06C)
System cable (3 m)
(ADF1027)
Operating instructions
Item
Media Receiver, Model: PDP-R06G
Color System
PAL/SECAM/NTSC/4.43NTSC/PAL-M/PAL-N
TV Function
Receiving System
PAL: B/G, D/K, I M, N SECAM: B/G, D/K NTSC: M 4.43NTSC : M
Tuner
VHF/UHF
44.25-863.25 MHz
CATV
Hyper-band, S1-S41ch
Auto Channel Preset
99 ch (Normal), 68 ch (Air, US type), 125 ch (Cable, US type), Auto Preset
Audio multiplex
NICAM/A2/BTSC System
Terminals
Rear
INPUT 1
COMPONENT VIDEO in, S-VIDEO in, AV in
INPUT 2
COMPONENT VIDEO in, S-VIDEO in, AV in
INPUT 3
S-VIDEO in, AV in, HDMI in*
Antenna
75
Din Type for VHF/UHF in
Front
INPUT 4
S-VIDEO, AV in (Audio input is shared with PC INPUT.)
PC
Analog RGB in
MONITOR OUT Terminal (Rear)
AV out
PHONES OUTPUT Terminal (Front)
16 - 32
recommended
SUB WOOFER OUTPUT Terminal (Rear)
Variable
Power Requirement
110 - 240 V(PDP-R06G), 220 - 240V(PDP-R06C) , 50/60 Hz, 16 W (0.4 W Standby)
Dimensions
420 (W)
× 90 (H) × 299 (D) mm
Weight
3.4 kg