background image
PIONEER CORPORATION
4-1, MEGURO 1-CHOME, MEGURO-KU
TOKYO 153-8654, JAPAN
PIONEER ELECTRONICS (USA) INC.
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.
TEL: (800) 421-1404
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium
TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936
TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia
TEL: (03) 9586-6300
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada
TEL: 1-877-283-5901
TEL: 905-479-4411
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.
Blvd.Manuel Avila Camacho 138 10 piso
Col.Lomas de Chapultepec, Mexico, D.F. 11000
TEL: 55-9178-4270
: 4413
: (02) 2521-3588
9901-6
: (0852) 2848-6488
Published by Pioneer Corporation.
Copyright © 2007 by Pioneer Corporation.
All rights reserved.
Publié par Pioneer Corporation. Copyright
© 2007 par Pioneer Corporation. Tous
droits réservés.
Owner's manual
Mode d'emploi
GEX-P10HD
<KOKNX> <07J00000>
Printed in China
Imprimé en Chine
<49.HTAPN.001> UC
HD RadioTM TUNER
SYNTONISEUR HD RadioTM
HD RadioTM Technology Manufactured Under
License From iBiquity Digital Corp. U.S. and
Foreign Patents. HD RadioTM and the HD Radio
logo are proprietary trademarks of iBiquity
Digital Corp.
Information to User
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment has been tested and found
to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation.If this equipment
dose cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the
equipment and receiver.
· Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
· Consult the dealer or an experienced radio/TV
technician for help.
Alteration or modifications carried out without
appropriate authorization may invalidate the
user's right to operate the equipment.
For Canadian model
This Class B digital apparatus complies with
Canadian ICES-003.
About this unit
This unit is an HD Radio tuner for a Pioneer
head unit featuring an IP-BUS input.
· This unit is designed for use in vehicles only.
WARNING
Handling the cord on this product or cords
associated with accessories sold with the product
may expose you to chemicals listed on proposition
65 known to the State of California and other
governmental entities to cause cancer and birth
defects or other reproductive harm.
Wash hands
after handling.
CAUTION
· Do not allow this unit to come into contact with
liquids. Electrical shock could result. Also, this unit
damage, smoke, and overheat could result from
contact with liquids.
· Keep this manual handy as a reference for
operating procedures and precautions.
· Always keep the volume low enough so that you
can hear sounds from outside the vehicle.
· Protect this unit from moisture.
Important (Serial number)
The serial number is located on the bottom of
this unit. For your own security and convenience,
be sure to record this number on the enclosed
warranty card.
Before You Start
English
After-sales service for
Pioneer products
Please contact the dealer or distributor from
where you purchased this unit for after-sales
service (including warranty conditions) or
any other information. In case the necessary
information is not available, please contact the
companies listed below:
Please do not ship your unit to the companies
at the addresses listed below for repair without
advance contact.
U.S.A
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
For warranty information please see the
Limited Warranty sheet included with this unit.
Visit our website
Visit us at the following site:
http://www.pioneerelectronics.com
1 Register your product. We will keep the details
of your purchase on file to help you refer to this
information in the event of an insurance claim
such as loss or theft.
2 Receive updates on the latest products and
technologies.
3 Download owner's manuals, order product
catalogues, research new products, and much
more.
About this manual
Operate this unit with the connected head
unit.
This manual explains the operation method
of external connection. If combined head unit
controls this unit as an external unit, see this
instruction manual.
If the combined head unit fully controls this
unit, refer to head unit's operation manual.
We recommend that you familiarize yourself
with the functions and their operation by
reading through the manual before you begin
using this unit
It is especially important that you read and
observe WARNINGs and CAUTIONs in this
manual.
Before You Start
English
Before You Start
English
About HD Radio broadcasting
HD Radio broadcasting is high quality audio
and data services. HD Radio broadcasting is
brought to you by your local FM/AM stations.
HD Radio broadcasting features the following:
· High quality audio
· FM multicasting
· Data services
: Sub channel
AM band
Analog AM
Analog AM
Digital AM
FM band
Analog FM
Analog FM
Digital FM
Analog FM
Digital FM-1ch
Digital FM-2ch
Digital FM-3ch
: Main channel


background image
Using as an external unit
The following head units operate this unit as
an external unit. For more details about the
external unit, refer to the head unit's manual.
Head unit group 1
The following head units featuring FUNCTION
button operation or SOFT KEY operation.
DEH-P9600MP, DEH-P5800MP, DEH-P4900MP,
DEH-P4800MP, DEH-P3900MP, DEH-P3800MP,
DEH-P2900MP, DEH-P960MP, DEH-P760MP,
DEH-P660, DEH-P580MP, DEH-P490MP,
DEH-P480MP, DEH-P390MP, FH-P5000MP,
DVH-P5000MP
Head unit group 2
The following head units featuring MULTI-
CONTROL operation.
DEH-P9800BT, DEH-P8600MP, DEH-P7900BT,
DEH-P7800MP, DEH-P6900UB, DEH-P6800MP,
DEH-P980BT, DEH-P880PRS, DEH-P860MP,
DEH-P790BT, DEH-P780MP, DEH-P690UB,
DEH-P680MP, DEH-P80MP, DEH-P8MP,
DEH-P600UB, DEH-P6000UB, DEH-P500UB*1,
DEH-P5000UB*1, DEH-P400UB*1,
DEH-P4000UB*1, DEH-P3000IB*1
*1 For these models, some operations are
different.
Head unit group 3
The following head units featuring touch panel
key operation.
AVH-P7600DVD, AVH-P7800DVD,
AVH-P5900DVD, AVH-P4900DVD,
AVH-P5000DVD, AVH-P4000DVD
Head unit group 4
The following head units are navigation units
featuring touch panel key operation.
AVIC-D2, AVIC-N2, AVIC-N3,
AVIC-Z1, AVIC-Z2, AVIC-D3, AVIC-N4
Function compatibility charts
Head unit group 1
Controls
Select HD Radio tuner as
an external source
Press SOURCE.
Select a band
To return to the
frequency display
Press BAND.
Perform manual tuning
Press or .
Perform seek tuning
Press and hold or .
Recall radio station
frequencies assigned
Press or .
Storing presets
Press and hold a button 1
to 6.
Select a function
Press FUNCTION (FUNC).
Change text information Press or in FUNC1 (F1).
Turn BSM (Best station
memory) on
Press or in FUNC2 (F2).
Switching reception
mode
Press or in FUNC3 (F3).
Switching local function Press or in FUNC4 (F4).
Switching seek mode
between ALL and HD
Press or in AUTO/
MANUAL (A/M).
Operating the HD Radio tuner
English
Head unit group 2
Controls
Select HD Radio tuner as
an external source
Press SOURCE.
Select a band
To return to the
frequency display
Press BAND.
Perform manual tuning
Push MULTI-CONTROL left
or right.
Perform seek tuning
Push and hold MULTI-
CONTROL left or right.
Recall radio station
frequencies assigned
Push MULTI-CONTROL up
or down.
Storing presets
Press and hold a button 1
to 6.
(*1 models)
Select one from 1 KEY to
6 KEY and then continue
pressing MULTI-CONTROL.
Select a function
Use MULTI-CONTROL.
Change text information Press MULTI-CONTROL in
FUNC1 (F1).
Turn BSM (Best station
memory) on
Press MULTI-CONTROL in
FUNC2 (F2).
Switching reception
mode
Press MULTI-CONTROL in
FUNC3 (F3).
Switching local function Press MULTI-CONTROL in
FUNC4 (F4).
Switching seek mode
between ALL and HD
Press MULTI-CONTROL in
AUTO/MANUAL (A/M).
Head unit group 3
Controls
Select HD Radio tuner as
an external source
Press SOURCE.
Select a band
To return to the
frequency display
Touch BAND.
Perform manual tuning
Touch or .
Perform seek tuning
Keep touching or .
Recall radio station
frequencies assigned
Touch or .
Storing presets
Keep touching one of 1 KEY
to 6 KEY.
Select a function
Touch A.MENU and then
touch FUNCTION.
Change text information Touch in FUNCTION 1.
Turn BSM (Best station
memory) on
Touch in FUNCTION 2.
Switching reception
mode
Touch in FUNCTION 3.
Switching local function Touch in FUNCTION 4.
Switching seek mode
between ALL and HD
Touch or in AUTO/
MANUAL.
Operating the HD Radio tuner
English
Head unit group 4
Controls
Select HD Radio tuner as
an external source
Switch source*2
Select a band
To return to the
frequency display
Touch BAND.
Perform manual tuning
Touch or .
Perform seek tuning
Keep touching or .
Recall radio station
frequencies assigned
Touch or .
Storing presets
Use one from
1 KEY to 6
KEY to register.
Change text information Perform FUNCTION 1 (F 1)*2
Turn BSM (Best station
memory) on
Perform FUNCTION 2 (F 2)*2
Switching reception
mode
Perform FUNCTION 3 (F 3)*2
Switching local function
Perform FUNCTION 4 (F 4)*2
Switching seek mode
between ALL and HD
Switch AUTO/MANUAL
(A/M)*2
*2 Operations may vary depending on the product.
For details, refer to operation manual supplied with
your head unit.
Perform manual tuning
Manual tuning (step by step)
Refer to Function compatibility charts.
· When an analog station is received, tuning
down operation is conducted within the
analog broadcasting. (6 2)
· If a digital broadcast is not yet received,
tuning-up operation tunes in the next analog
station. (2 6)
Analog FM
1
Analog FM
6
Analog FM
2
Digital FM-1ch
3
Digital FM-2ch
4
Digital FM-3ch
5
Displaying text information
Select the desired information.
Refer to Function compatibility charts.
Call sign or frequency--song title--
artist name--program type
Operating the HD Radio tuner
English
Operating the HD Radio tuner
English
Storing the strongest
broadcast frequencies
BSM (best stations memory) lets you
automatically store the six strongest broadcast
frequencies.
Turn BSM on
Refer to Function compatibility charts.
· The six strongest broadcast frequencies are
stored in the order of their signal strength.
· Sub channel cannot be registered.
Switching reception mode
If a digital broadcast reception condition gets
poor, this unit automatically switches to the
analog broadcast of the same frequency level.
Switching reception mode
Refer to Function compatibility charts.
ON--Digital broadcast/analog broadcast
automatic switching
OFF--Analog broadcast fixed setting
Switching local function
Local seek tuning lets you tune in only those
radio stations with sufficiently strong signals
for good reception.
Turn local seek tuning on
Refer to Function compatibility charts.
FM: OFF--LEVEL 1--LEVEL 2--LEVEL 3--LEVEL 4
AM: OFF--LEVEL 1--LEVEL 2
· The LEVEL 4 setting allows reception of only
the strongest stations, while lower settings let
you receive regressively weaker stations.
Switching Seek mode
Seek tuning settings can be changed.
Select the seek mode
Refer to Function compatibility charts.
AUTO (ALL) --Seek tuning (normal condition)
MANUAL (HD) --Seek tuning (Digital
broadcast stations seek)


background image
Connections
English
Connecting the units
Head unit
(sold separately)
Antenna jack
Antenna cable
(supplied)
3 m (9 ft. 10 in.)
Black (chassis ground)
Connect to a clean, paint-free metal location.
Fuse (2 A)
Yellow
Connect to the constant
12 V supply terminal.
3 m (9 ft. 10 in.)
IP-BUS cable
IP-BUS cable
(supplied)
Blue
To IP-BUS input
(blue)
Multi-CD player
(sold separately)
Black
This unit
Blue/White
Control signal is output through blue/white cable
when Pioneer head unit is turned on. Connect it
to the vehicle's auto-antenna relay control
terminal (max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
Car antenna cable (form vehicle's antenna)
Connect the car antenna cable to this unit's
antenna input. It is not necessary to connect to
head unit's antenna input.
If you use this unit with a navigation system that
can receive traffic information from the built-in
FM tuner, connect the car antenna cable to both
this unit and the navigation system with an
antenna splitter or to a separate antenna.
Installation
English
Connections
Important
· Use this unit in a vehicle of a 12-volt battery and
negative grounding.
· To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
-- Disconnect the negative terminal of the battery
before installation.
-- Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
-- Place all cables away from moving parts, such as
gear shift and seat rails.
-- Place all cables away from hot places, such as
near the heater outlet.
-- Do not pass the yellow cable through a hole into
the engine compartment to connect to a battery.
-- Do not shorten any cables.
-- Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
-- Use a fuse of the rating prescribed.
· IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
· Place antenna cable as far away as possible from
the other cables to prevent noise.
· Black cable is ground. This cable and other
product's ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
Installing this unit
Important
· Check all connections and systems before final
installation.
· Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
· Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
· Do not install this unit where:
-- it may interfere with operation of the vehicle.
-- it may cause injury to a passenger as a result of a
sudden stop.
· When mounting this unit, make sure none of
the leads are trapped between this unit and the
surrounding metalwork or fittings.
· Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
· Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring or
other important parts.
· If this unit installed in the passenger compartment,
anchor it securely so it does not break free while
the vehicle is moving, and cause injury or an
accident.
· If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not caught or pinched in
the mechanism and cause a short-circuit.
Mounting with hook and loop fasteners
Thoroughly wipe off the surface before affixing
the hook and loop fasteners.
· If the hook fasteners adhere to the car mat
directly, you may install this unit without using the
loop fasteners.
Mount this unit using the hook and
loop fasteners.
Hook fastener
This unit
Car mat or chassis
Loop fastener
Additional Information
English
Specifications
General
Rated power source ............ 14.4 V DC
(allowable voltage range:
10.8 V to 15.1 V DC)
Grounding system............... Negative type
Max. current consumption
..................................... 2.0 A
Dimensions (W × H × D) ..... 121 mm × 30 mm × 79 mm
(4-3/4 in. × 1-1/8 in. × 3-1/8 in.)
Weight ............................... 350 g (0.8 lbs)
Analog FM tuner
Frequency range ................. 87.9 MHz to 107.9 MHz
Usable sensitivity ................ 14 dBf (0.7 V/75 W, mono,
S/N: 30 dB)
Signal-to-noise ratio............ 61 dB (IHF-A network)
Digital FM tuner
Frequency range ................ 87.9 MHz to 107.9 MHz
Signal-to-noise ratio............ 70 dB (IHF-A network)
Frequency response............. 30 Hz to 15 000 Hz (±3 dB)
Stereo separation................ 70 dB (at 1 kHz)
Analog AM tuner
Frequency range ................. 530 kHz to 1 710 kHz (10 kHz)
Usable sensitivity................. 50 V (S/N: 20 dB)
Signal-to-noise rati.............. 58 dB (IHF-A network)
Digital AM tuner
Frequency range ................. 530 kHz to 1 710 kHz (10 kHz)
Signal-to-noise ratio............ 70 dB (IHF-A network)
Frequency response............. 40 Hz to 15 000 Hz (±3 dB)
Stereo separation................ 70 dB (at 1 kHz)
Note
Specifications and the design are subject to
possible modifications without notice due to
improvements.


background image
Avant de commencer
Français
Avant de commencer
Français
Installation
Français
Connexions
Français
Connexion des appareils
3 m
3 m
Prise d'antenne
Câble IP-BUS
Entrée IP-BUS (Bleu)
Bleu
Cet appareil
Noire
Lecteur de CD
à chargeur
(vendu séparément)
Câble d'antenne
(fourni)
Appareil central
(vendu séparément)
Câble IP-BUS
(fourni)
Bleu/blanc
Le signal de commande est sorti par le câble
bleu/blanc quand l'unité centrale Pioneer est
mise sous tension. Connectez-le à la prise de
commande de relais d'antenne automatique
(max. 300 mA, 12 V CC). Si le véhicule est équipé
d'une antenne de vitre, connectez-le à la prise
d'alimentation de l'amplificateur d'antenne.
Câble d'antenne de voiture (de l'antenne du véhicule)
Connectez la câble d'antenne de la voiture à l'entrée
d'antenne de l'appareil. Il n'est pas nécessaire de
connecter l'entrée d'antenne de l'appareil central.
Fusible (2 A)
Jaune
Connectez à une prise
d'alimentation constante 12 V.
Si vous utilisez cet appareil avec un système de
navigation qui peut recevoir les informations de
circulation routière du tuner intégré, connectez le
câble d'antenne de la voiture à la fois à cet
appareil et au système de navigation avec un
séparateur d'antenne ou utilisez une antenne
séparée.
Noire (masse au châssis)
Connectez à une section métallique
propre et sans peinture.
Technologie HD RadioTM fabriquée sous licence
de iBiquity Digital Corp. pour les brevets aux
États-Unis et dans les autres pays. HD RadioTM
et le logo HD Radio sont des marques de
commerce de iBiquity Digital Corp.
Informations pour l'utilisateur
Toute altération ou modification réalisée sans
l'autorisation appropriée peut rendre invalide le
droit de l'utilisateur d'utiliser l'appareil.
Pour le modèle canadien
Cet appareil de classe B est conforme avec la
norme canadienne ICES-003.
Quelques mots sur cet
appareil
Cet appareil est un tuner HD Radio pour un
appareil central Pioneer équipé d'une entrée
IP-BUS.
· Ce appareil est conçu pour une utilisation à
bord de véhicules uniquement.
PRÉCAUTION
· Ne laissez pas cet appareil venir en contact
avec des liquides. Cela pourrai provoquer une
électrocution. Tout contact avec des liquides
pourrait aussi provoquer des dommages, de la
fumée et une surchauffe de l'appareil.
· Conservez ce mode d'emploi à portée de main
afin de vous y référer pour les modes d'opération
et les précautions.
· Maintenez toujours le niveau d'écoute à une
valeur telle que vous puissiez entendre les sons
provenant de l'extérieur du véhicule.
· Protégez l'appareil contre l'humidité.
Service après-vente pour
les produits Pioneer
Veuillez contacter le revendeur ou le
distributeur auprès duquel vous avez acheté
cet appareil pour bénéficier du service après
vente (y compris les clauses de la garantie)
ou pour toute autre informations. Dans le cas
ou les informations nécessaire ne sont pas
disponible, veuillez contacter les compagnies
de la liste ci-dessous:
Veuillez ne pas envoyer votre appareil aux
adresses des compagnies de la liste ci-dessous
pour réparation sans avoir pris au préalable
contact avec eux.
États-Unis
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
CANADA
Pioneer Electronics of Canada, Inc.
CUSTOMER SATISFACTION DEPARTMENT
300 Allstate Parkway
Markham, Ontario L3R 0P2
1-877-283-5901
905-479-4411
Pour les informations relatives à la garantie,
veuillez vous reporter à la carte de garantie
limitée fournie avec cet appareil.
Visitez notre site web
Rendez-vous nous visite au site web suivant:
http://www.pioneerelectronics.com
1 Enregistrez votre produit. Nous conserverons les
détails de votre achat dans un fichier pour vous
aider à vous référer à cette information dans le
cas d'une réclamation d'assurance en cas de
perte ou de vol.
2 Recevez des nouvelles de nos derniers produits et
technologies.
3 Téléchargez des modes d'emploi, des catalogues
de produits, recherchez de nouveaux produits,
etc.
Quelques mots sur ce mode
d'emploi
Utilisez cet appareil avec l'appareil central
connecté.
Ce mode d'emploi explique la méthode de
commande de la connexion extérieure. Si
l'appareil central commande cet appareil
comme un appareil extérieur, reportez-vous à
ce mode d'emploi.
Si l'appareil central commande complètement
cet appareil, reportez-vous au mode d'emploi
de l'appareil central.
Nous vous recommandons de vous familiariser
avec les fonctions et leurs utilisation en lisant
l'ensemble du mode d'emploi avant de
commencer à utiliser l'appareil.
Il est particulièrement important que vous lisiez
et respectiez les indications ATTENTION et
PRÉCAUTION de ce mode d'emploi.
À propos des émissions HD
Radio
Les émissions HD Radio offrent une grande
qualité audio et des services de données. Les
émissions HD Radio sont diffusées par vos
stations locales FM/AM.
Les caractéristiques des émissions HD Radio
sont les suivantes:
· Son de haute qualité
· FM multiplex
· Services de données
: Canal secondaire
Bande AM
AM analogique
AM analogique
AM numérique
Bande FM
FM analogique
FM analogique
FM numérique
FM analogique
FM numérique-1ca
FM numérique-2ca
FM numérique-3ca
: Canal principal
Connexions
Important
· Utilisez cet appareil dans un véhicule avec
un batterie de 12 volts et une mise à la masse
négative.
· Pour éviter un court-circuit, une surchauffe ou un
dysfonctionnement, assurez-vous de respecter les
instructions suivantes.
-- Déconnectez la borne négative de la batterie
avant l'installation.
-- Fixez le câblage avec des serre-files ou de la
bande adhésive. Pour protéger les câbles,
enroulez-les de bande adhésive là où ils sont en
contact avec des parties métalliques.
-- Placez les câbles à l'écart de toutes les parties
mobiles, telles que le levier de changement de
vitesse et les rails des sièges.
-- Placez les câbles à l'écart de tous les endroits
chauds, par exemple les sorties de chauffage.
-- Ne faites pas passer le câble jaune à travers
un trou dans le compartiment moteur pour le
connecter à la batterie.
-- Ne raccourcissez pas les câbles.
-- Ne coupez jamais l'isolation du câble
d'alimentation de cet appareil pour partager
l'alimentation avec un autre équipement. La
capacité en courant du câble est limitée.
-- Utilisez un fusible correspondant aux
caractéristiques spécifiées.
· Les connecteurs IP-BUS utilisent un codage en
couleur. Assurez-vous de connecter ensemble des
connecteurs de la même couleur.
· Placez le câble d'antenne aussi loin que possible
des autres câbles pour éviter le bruit.
· Le câble noir est le câble de masse. Ce câble
et les autres câbles de masse des produits
(particulièrement les produits avec des courants
élevés tels qu'un amplificateur de puissance)
doivent être câblés séparément. Sinon, un
incendie ou un mauvais fonctionnement peuvent
se produire si ces câbles sont déconnectés
accidentellement.
Installation de l'appareil
Important
· Vérifiez toutes les connexions et tous les systèmes
avant l'installation finale.
· N'utilisez pas de pièces détachées non autorisées.
L'utilisation de pièces non autorisées peut
provoquer des dysfonctionnements.
· Consultez votre revendeur si l'installation nécessite
le percement de trous ou d'autres modifications du
véhicule.
· N'installez pas ce appareil où:
-- Il peut interférer avec la commande du véhicule.
-- Il peut blesser un passager en cas d'arrêt soudain
du véhicule.
· Lors du montage de cet appareil, assurez-
vous qu'aucun fil n'est coincé entre l'appareil
et les parties métalliques ou les équipements
environnants.
· Ne montez pas cet appareil dans un endroit située
près d'un orifice de chauffage , où il serait affecté
par la chaleur, ou près des portes où il pourrait être
mouillé par la pluie.
· Avant de percer un trou de montage, vérifiez
toujours derrière l'emplacement où vous voulez
percer le trou. Ne percez pas de trou dans le
conduit d'essence, le conduit de frein, un câble
électrique ou d'autres pièces importantes.
· Si l'appareil est installé dans le compartiment
passager, fixez-le solidement de façon qu'il ne se
détache pas quand le véhicule est en mouvement,
ce qui risquerait de provoquer des blessures ou un
accident.
· Si l'appareil est installé sous un siège avant,
assurez-vous qu'in ne gêne pas le déplacement
du siège. Faites passer tous les fils et les cordons
soigneusement autour du mécanisme de glissière
de façon qu'ils ne soient pas coincés dans le
mécanisme ou pincés par celui-ci, et ne provoquent
pas de court-circuit.
Montage en utilisant une bande velcro
Essuyez bien la surface avant de fixer les
bandes velcro.
· Si la bande velcro (côté crochets) adhère
directement au tapis de sol, vous pouvez installer
cet appareil sans utiliser la bande velcro (côté
boucles).
Montez cet appareil en utilisant les
bandes velcro.
Bande velcro (crochets)
Cet appareil
Tapis ou châssis de la voiture.
Bande velcro (boucles)


background image
Utilisation du tuner HD Radio
Français
Utilisation du tuner HD Radio
Français
Utilisation du tuner HD Radio
Français
Utilisation comme source
extérieure
Les appareils centraux suivants peuvent
commander cet appareil en tant que source
extérieure. Pour avoir plus de détails sur la
source extérieure, reportez-vous au mode
d'emploi de l'appareil central.
Appareils centraux du groupe 1
Les appareil centraux suivants disposent de
la touche FUNCTION ou du fonctionnement
par SOFT KEY (touches logicielles).(touches
logicielles).
DEH-P9600MP, DEH-P5800MP, DEH-P4900MP,
DEH-P4800MP, DEH-P3900MP, DEH-P3800MP,
DEH-P2900MP, DEH-P960MP, DEH-P760MP,
DEH-P660, DEH-P580MP, DEH-P490MP,
DEH-P480MP, DEH-P390MP, FH-P5000MP,
DVH-P5000MP
Appareils centraux du groupe 2
Les appareils centraux suivants disposent de
MULTICONTROL.
DEH-P9800BT, DEH-P8600MP, DEH-P7900BT,
DEH-P7800MP, DEH-P6900UB, DEH-P6800MP,
DEH-P980BT, DEH-P880PRS, DEH-P860MP,
DEH-P790BT, DEH-P780MP, DEH-P690UB,
DEH-P680MP, DEH-P80MP, DEH-P8MP,
DEH-P600UB, DEH-P6000UB, DEH-P500UB*1,
DEH-P5000UB*1, DEH-P400UB*1,
DEH-P4000UB*1, DEH-P3000IB*1
*1 Pour ces modèles, certaines opérations
peuvent différées.
Appareils centraux du groupe 3
Les appareils centraux suivants disposent d'un
clavier tactile.
AVH-P7600DVD, AVH-P7800DVD,
AVH-P5900DVD, AVH-P4900DVD,
AVH-P5000DVD, AVH-P4000DVD
Appareils centraux du groupe 4
Les appareils centraux suivants sont des
appareils de navigation disposant d'un clavier
tactile.
AVIC-D2, AVIC-N2, AVIC-N3,
AVIC-Z1, AVIC-Z2, AVIC-D3, AVIC-N4
Tableaux de compatibilité des
fonctions
Appareils centraux du groupe 1
Commandes
Sélection du tuner HD
Radio comme source
extérieure
Appuyez sur SOURCE.
Sélection d'une bande
Pour retourner à
l'affichage de la
fréquence
Appuyez sur BAND.
Pour réaliser l'accord
manuel
Appuyez sur ou .
Pour réaliser l'accord
automatique
Appuyez de façon continue
sur ou .
Rappel de fréquences de
station affectées
Appuyez sur ou .
Préréglages mémorisés
Maintenez pressée une
touche de 1 à 6.
Sélection d'une fonction Appuyez sur FUNCTION
(FUNC).
Changement du texte
d'information
Appuyez sur ou dans
FUNC1 (F1).
Mise en service de BSM
(mémoire de la meilleure
station)
Appuyez sur ou dans
FUNC2 (F2).
Commutation du mode
de réception
Appuyez sur ou dans
FUNC3 (F3).
Commutation de la
fonction locale
Appuyez sur ou dans
FUNC4 (F4).
Commutation du mode
d'accord sur ALL et HD
Appuyez sur ou dans
AUTO/MANUAL (A/M).
Appareils centraux du groupe 4
Commandes
Sélection du tuner HD
Radio comme source
extérieure
Commutation de la source*2
Sélection d'une bande
Pour retourner à
l'affichage de la
fréquence
Touchez BAND.
Pour réaliser l'accord
manuel
Touchez ou .
Pour réaliser l'accord
automatique
Touchez ou de façon
prolongée.
Rappel de fréquences de
station affectées
Touchez ou .
Préréglages mémorisés
Utilisez 1 KEY à 6 KEY pour
enregistrer le préréglage.
Changement du texte
d'information
Réalisez FUNCTION 1 (F 1)*2
Mise en service de BSM
(mémoire de la meilleure
station)
Réalisez FUNCTION 2 (F 2)*2
Commutation du mode
de réception
Réalisez FUNCTION 3 (F 3)*2
Commutation de la
fonction locale
Réalisez FUNCTION 4 (F 4)*2
Commutation du mode
d'accord sur ALL et HD
Commutation de AUTO/
MANUAL (A/M)*2
*2 Les opérations peuvent varier en fonction du
produit. Pour les détails, reportez-vous au mode
d'emploi fourni avec votre appareil central.
Pour réaliser l'accord manuel
Accord manuel (étape par étape)
Reportez-vous aux tableaux de compatibilité
des fonctions.
· Quand une station analogique est reçue,
l'opération d'accord est réalisée parmi les
station stations analogique. (6 2)
· Si une station numérique n'est pas encore
reçue, l'opération d'accord permet d'accorder
la station analogique suivante. (2 6)
FM analogique
1
FM analogique
6
FM analogique
2
FM numérique-1ca
3
FM numérique-2ca
4
FM numérique-3ca
5
Appareils centraux du groupe 2
Commandes
Sélection du tuner HD
Radio comme source
extérieure
Appuyez sur SOURCE.
Sélection d'une bande
Pour retourner à
l'affichage de la
fréquence
Appuyez sur BAND.
Pour réaliser l'accord
manuel
Poussez MULTI-CONTROL
vers la gauche ou vers la
droite.
Pour réaliser l'accord
automatique
Poussez de façon continue
MULTI-CONTROL vers la
gauche ou vers la droite.
Rappel de fréquences de
station affectées
Poussez MULTI-CONTROL
vers le haut ou vers le bas.
Préréglages mémorisés
Maintenez pressée une
touche de 1 à 6.
(Modèles *1)
Choisissez une touche de
1 KEY à 6 KEY et continuez
en appuyant sur MULTI-
CONTROL
Sélection d'une fonction Utilisez MULTI-CONTROL.
Changement du texte
d'information
Appuyez sur MULTI-
CONTROL dans FUNC1 (F1).
Mise en service de BSM
(mémoire de la meilleure
station)
Appuyez sur MULTI-
CONTROL dans FUNC2 (F2).
Commutation du mode
de réception
Appuyez sur MULTI-
CONTROL dans FUNC3 (F3).
Commutation de la
fonction locale
Appuyez sur MULTI-
CONTROL dans FUNC4 (F4).
Commutation du mode
d'accord sur ALL et HD
Appuyez sur MULTI-
CONTROL dans AUTO/
MANUAL (A/M).
Appareils centraux du groupe 3
Commandes
Sélection du tuner HD
Radio comme source
extérieure
Appuyez sur SOURCE.
Sélection d'une bande
Pour retourner à
l'affichage de la
fréquence
Touchez BAND.
Pour réaliser l'accord
manuel
Touchez ou .
Pour réaliser l'accord
automatique
Touchez ou de façon
prolongée.
Rappel de fréquences de
station affectées
Touchez ou .
Préréglages mémorisés
Touchez de façon prolongée
1 KEY à 6 KEY.
Sélection d'une fonction Touchez A.MENU puis
FUNCTION.
Changement du texte
d'information
Touchez dans
FUNCTION 1.
Mise en service de BSM
(mémoire de la meilleure
station)
Touchez dans
FUNCTION 2.
Commutation du mode
de réception
Touchez dans
FUNCTION 3.
Commutation de la
fonction locale
Touchez dans
FUNCTION 4.
Commutation du mode
d'accord sur ALL et HD
Touchez ou dans AUTO/
MANUAL.
Affichage des informations
textuelles
Sélectionnez les informations
désirées.
Reportez-vous aux tableaux de compatibilité
des fonctions.
Signe d'appel ou fréquence--titre de la
chanson--nom de l'artiste--type de programme
Mémorisation des fréquences
d'émission les plus
puissantes
BSM (mémoire des meilleures stations) vous
permet de mémoriser les six fréquences
d'émission les plus puissantes.
Mise en service de la fonction BSM
Reportez-vous aux tableaux de compatibilité
des fonctions.
· Les six fréquences d'émission les plus
puissantes sont mémorisées dans l'ordre de
puissance du signal.
· Un canal secondaire ne peut pas être
enregistré.
Commutation du mode de
réception
Si les conditions de réception d'une émission
numérique deviennent mauvaises, cet appareil
commute automatiquement sur l'émission
analogique du même niveau de fréquence.
Commutation du mode de réception
Reportez-vous aux tableaux de compatibilité
des fonctions.
ON--Commutation automatique entre les
émissions numériques/analogiques
OFF--Réglage fixé sur les émissions
analogiques
Commutation de la fonction
locale
La fonction d'accord sur les signaux puissant
vous permet d'accorder les stations radio avec
un signal suffisamment puissant pour obtenir
une bonne réception.
Mise en service de la fonction
d'accord sur les signaux puissant
Reportez-vous aux tableaux de compatibilité
des fonctions.
FM: OFF--LEVEL 1--LEVEL 2--LEVEL 3--LEVEL 4
AM: OFF--LEVEL 1--LEVEL 2
· Le réglage LEVEL 4 permet la réception des
seules stations très puissantes ; les autres
réglages autorisent, dans l'ordre décroissant,
la réception des stations de moins en moins
puissantes.
Utilisation du tuner HD Radio
Français