ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
c
BCT-1540
ARP3085
T ZZV NOV. 2000 Printed in Japan
CANAL PLUS TUNER
Type
Model
Power Requirement
Remarks
BCT-1540
NYXK/SK
AC230V
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 3
3. SCHEMATIC DIAGRAM ....................................... 6
4. PCB CONNECTION DIAGRAM .......................... 28
5. PCB PARTS LIST ............................................... 34
CONTENTS
6. ADJUSTMENT .................................................... 35
7. GENERAL INFORMATION ................................ 36
7.1 IC ................................................................. 36
8. PANEL FACILITIES AND SPECIFICATIONS .... 59
2
BCT-1540
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause
cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols
(fast operating fuse) and/or
(slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible
(fusible de type rapide) et/ou
(fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are identified
by marking with a
on the schematics and on the parts list
in this Service Manual.
The use of a substitute replacement component which does
not have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in
this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
PIONEER.
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
such as Simpson Model 229-2 or equivalent between the
earth ground and all exposed metal parts of the appliance
(input/output terminals, screwheads, metal overlays, control
shaft, etc.). Plug the AC line cord of the appliance directly
into a 120V AC 60Hz outlet and turn the AC power switch
on. Any current measured must not exceed 0.5mA.
(FOR USA MODEL ONLY)
Leakage
current
tester
Reading should
not be above
0.5mA
Device
under
test
Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
Earth
ground
AC Leakage Test
3
BCT-1540
2.1 PACKING
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
·Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
·The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
·Screws adjacent to mark on the product are used for disassembly.
1
3
4
5
9
10
6
8
2
7
1
Packing Case
BHD1488
2
Side Pad L
BHA1146
3
Side Pad R
BHA1147
4
Remote Control Unit
BXD1049
5
Sheet
AHG1153
NSP
6
Battery (R03/AAA) 2P
VEM1018
7
Scart Cable(1m:Black)
BDH1027
8
AC Power Cord (2m:Black)
BDG1035
NSP
9
CE Declaration Sheet
BRM1045
NSP
10
Catalogue Bag
BHG1047
PACKING PARTS LIST
Mark No.
Description
Part No.
4
BCT-1540
2.2 EXTERIOR SECTION
19
19
19
19
5
16
16
22
19
14
19
19
15
13
17
19
19
19
19
19
19
19
19
11
3
1
18
6
2
10
19
19
7
8
9
4
12
21
20
A
D
C
B
5
BCT-1540
1
MAIN ASSY
BWE1111
2
FRONT ASSY
BWE1102
3
CARD ASSY
BWE1080
4
POWER ASSY
BXF1146
5
Fuse (0109: T2.5AH250V)
REK1102
6
Front Panel Assy
BWX1190
7
Plastic Base
BMA1002
8
Chassis
BNA1151
9
PCB Support
AEC1215
10
21P FFC(J1)
BDD1046
11
12P FFC(J2)
BDD1022
12
Rear Panel Assy
BWX1177
NSP
13
Name Label
BAL1411
14
Washer Faced Nut
BBN1005
15
Joint
BMR1133
16
Hexagon Headed screw
BBA1059
17
Barrier
BEC1231
18
Bonnet Case
BNE1120
19
Screw
BBZ30P080FZK
20
Rear Panel Cover
BAP1003
21
Serial No. Label
BAX1287
NSP
22
Bar Code Label
BAL1310
EXTERIOR SECTION PARTS LIST
Mark No.
Description
Part No.