background image
SN 29343138 TX-L5.E
AV Receiver
TX-L5
Instruction Manual
Thank you for purchasing the Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new AV Receiver.
Please retain this manual for future reference.
Contents
Getting started
Before Using Your AV Receiver 2
Other
Enjoying Surround mode/
Recording
Enjoying music or videos
Turning on the AV Receiver/
Speaker Setup


background image
2
SN 29343138 TX-L5.E
1. Read Instructions ­ All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions ­ The safety and operating instructions
should be retained for future reference.
3. Heed Warnings ­ All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions ­ All operating and use instructions should
be followed.
5. Cleaning ­ Unplug the appliance from the wall outlet before
cleaning. The appliance should be cleaned only as
recommended by the manufacturer.
6. Attachments ­ Do not use attachments not recommended by
the appliance manufacturer as they may cause hazards.
7. Water and Moisture ­ Do not use the appliance near water ­for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories ­ Do not place the appliance on an unstable cart,
stand, tripod, bracket, or table. The appliance may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the appliance.
Any mounting of the appliance should follow the manufacturer's
instructions, and should use a mounting accessory
recommended by the manufacturer.
9. An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
10.Ventilation ­ Slots and openings in
the cabinet are provided for
ventilation and to ensure reliable
operation of the appliance and to protect it from overheating, and
these openings must not be blocked or covered. The openings
should never be blocked by placing the appliance on a bed, sofa,
rug, or other similar surface. The appliance should not be placed
in a built-in installation such as a bookcase or rack unless proper
ventilation is provided. There should be free space of at least 20
cm (8 in.) and an opening behind the appliance.
11.Power Sources ­ The appliance should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your appliance dealer or local power company.
12.Grounding or Polarization ­ The appliance may be equipped
with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized
plug.
13.Power-Cord Protection ­ Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit
from the appliance.
14.Outdoor Antenna Grounding ­ If an outside antenna or cable
system is connected to the appliance, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for
the grounding electrode. See Figure 1.
15.Lightning ­ For added protection for the appliance during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the
appliance due to lightning and power-line surges.
16.Power Lines ­ An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
17.Overloading ­ Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire
or electric shock.
18.Object and Liquid Entry ­ Never push objects of any kind into
the appliance through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the appliance.
19.Servicing ­ Do not attempt to service the appliance yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
20.Damage Requiring Service ­ Unplug the appliance form the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into the
appliance,
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the appliance to its normal operation,
E. If the appliance has been dropped or damaged in any way,
and
F. When the appliance exhibits a distinct change in performance
­ this indicates a need for service.
Important Safeguards
PORTABLE CART WARNING
S3125A
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING


background image
3
SN 29343138 TX-L5.E
I For British models
Replacement and mounting of an AC plug on the power supply cord
of this unit should be performed only by qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with the
following code:
Blue
: Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse need to be
replaced, please ensure that the replacement fuse has a rating of 5
amperes and that it is approved by ASTA or BSI to BS1362. Check
for the ASTA mark or the BSI mark on the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE
SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE
REMOVED AND THE PLUG CUT OFF AND DISPOSED OF
SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK
IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE
SOCKET.
If in any doubt, consult a qualified electrician.
Precautions
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC ­ NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
S2898A
21.Replacement Parts ­ When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22.Safety Check ­ Upon completion of any service or repairs to the
appliance, ask the service technician to perform safety checks to
determine that the appliance is in proper operation condition.
23.Wall or Ceiling Mounting ­ The appliance should be mounted to
a wall or ceiling only as recommended by the manufacturer.
24.Heat ­ The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
I For U.S. models
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Section 820-40 of the NEC which provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for
help.
I For Canadian models
NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
I Modele pour les Canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B
EST CON-FORME À LA NORME NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU'AU FOND.
FIGURE 1:
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE, ANSI/NFPA 70
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
INDUSTRIESTRASSE 20
82110 GERMERING,
GERMANY
GERMERING, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
I. MORI
declare in own responsibility, that the ONKYO product described
in this instruction manual is in compliance with the corresponding
technical standards such as EN60065, EN55013, EN55020 and
EN61000-3-2, -3-3.


background image
4
SN 29343138 TX-L5.E
Features
Memory Preservation
This unit does not require memory preservation batteries.
A built-in memory power backup system preserves the
contents of memory during power failures and even when the
POWER switch is set to OFF.
The POWER switch must be set to ON in order to charge the
backups system. The memory preservation period after the unit
has been turned off varies depending on climate and
placement of the unit. On average, memory contents are
protected over a period of a few weeks after the time the unit
has been turned off. This period is shorter when the unit is
exposed to a very humid climate.
Amplifier Features
I Rated output power (6 ohms, 1 kHz, 0.6% THD):
Front 22 W + 22 W, center 22 W, surround 22 W + 22 W
I 24-bit DSP chip featuring high-speed processing and
excellent reliability
I Stabilized ground potential, which is the basis of audio
signal amplitudes
I Dolby* Digital & Dolby Pro Logic II decoder and DTS**
decoder
I Acoustic Control function
I Subwoofer pre-output
I Five sets of audio input connectors and three sets of audio
output connectors
I S-Video input/output
I Heat-resistance, slim power transformer
I Large extruded-aluminum heat sinks
I Three digital input connectors
I Onkyo-original surround modes with five sophisticated
modes (Orchestra, Unplugged, Studio Mix, TV Logic and All
Channel Stereo) for natural audio reproduction
I Late Night function
FM/AM Tuner Features
I 30 FM/AM random presets
I FM auto tuning
I FM indoor antenna supplied
I AM indoor antenna supplied
* Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic" and the double-D symbol are trademarks of
Dolby Laboratories. Confidential Unpublished Works. ©1992-
1997 Dolby Laboratories. All rights reserved.
** Manufactured under license from Digital Theater Systems, Inc.
US Pat. No.5,451,942 and other worldwide patents issues and
pending, "DTS" and "DTS Digital Surround" are trademarks of
Digital Theater Systems, Inc. ©1996 Digital Theater Systems,
Inc. All Rights reserved.
1. Recording Copyright
Recording of copyrighted material for other than personal use is
illegal without permission of the copyright holder.
2. AC Fuse
The fuse is located inside the chassis and is not user-serviceable. If
power does not come on, contact your Onkyo authorized service
station.
3. Care
From time to time you should wipe the front and rear panels and the
cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a
weak solution of mild detergent and water, wring it out dry, and wipe
off the dirt. Following this, dry immediately with a clean cloth. Do not
use rough material, thinners, alcohol or other chemical solvents or
cloths since these could damage the finish or remove the panel
lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ
THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs according to
country or region. Be sure that the power supply voltage of the area
where this unit will be used meets the required voltage (e.g., AC 230
V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.
Worldwide models are equipped with a voltage selector to conform
to local power supplies. Be sure to set this switch to match the
voltage of the power supply in your area before plugging in the unit.
Precautions


background image
5
SN 29343138 TX-L5.E
Table of Contents
Important Safeguards/Precautions/Features/Table of Contents ....................... 2­5
Getting Started
Supplied Accessories ............................................................................................ 6
Preparing the Remote Controller .......................................................................... 7
Index to Parts and Controls .................................................................................. 8
Connecting to Audio/Video Equipment ................................................................ 12
Positioning Speakers .......................................................................................... 14
Connecting Speakers .......................................................................................... 15
Making Antenna (Aerial) Connections ................................................................. 16
Connection for remote control (z) .................................................................... 18
Turning on the AV Receiver/Speaker Setup
Connecting the Power/Turning on the AV Receiver ............................................ 19
Speaker Setup .................................................................................................... 20
Enjoying music or videos
Listening to the Radio ......................................................................................... 23
Playing the Connected Source ........................................................................... 26
Various Functions Common to all the Sources ................................................... 28
Enjoying Surround mode/Recording
Enjoying the Surround Modes ............................................................................. 30
Recording a source ............................................................................................. 35
Other
Troubleshooting .................................................................................................. 36
Specifications ...................................................................................................... 38
Memo .................................................................................................................. 39