120V AC, 60Hz
110-240V AC, 50/60 Hz
Ref. No. 3735
Schematic diagram & Printed circuit board view only
FOUND ON SOME COMPONENT
PARTS INDICATES THE CRITICAL FOR RISK OF
FIRE AND ELECTRIC SHOCK.
WHEN REPLACING, BE SURE TO USE PARTS OF
MAKE LEAKAGE-CURRENT OR RESISTANCE
MEASUREMENTS TO DETERMINE THAT EXPOSED
PARTS ARE ACCEPTABLY INSULATED FROM THE
SUPPLY CIRCUIT BEFORE RETURNING THE
APPLIANCE TO THE CUSTOMER.
Specifications and features are subject to change without notice.
AC 120V, 60 Hz (North America models)
AC 110-240V, 50/60 Hz (Other models)
17 1/8" x 3 7/8" x 12 11/16" (W/H/D)
NTSC (North America models)
PAL/NTSC (Other models)
Regional restriction code
Region 1 (North America)
Region 4 (Central and South America and Australia)
Frequency range (digital audio)
48 kHz sampling 4 Hz to 22 kHz
(DVD linear sound)
96 kHz sampling 4 Hz to 44 kHz
Signal-to-noise ratio (digital audio)
More than 90 dB
Audio dynamic range (digital audio)
More than 95 dB
Harmonic distortion (digital audio)
Less than 0.005 %
Wow and flutter
Below measurable level
Temperature: 5 C to 35 C (41 F to 95 F)
Operation status: Horizontal
1.0 V (p-p), 75 ohm, negative sync ., pin jack x 1
(Y) 1.0 V (p-p), 75 ohm, negative sync., Mini DIN 4-pin1
(C) 0.286V (p-p), 75 ohm
Component video output
(Y) 1.0 V (p-p), 75 ohm, negative sync., pin jack x 1
(PB)/(PR) 0.7V (p-p), 75 ohm pin jack x 2
Audio output (digital output Optical)
Optical connector x 1
Audio output (digital output Coaxial)
0.5 V(p-p),75 ohm, pin jack x 1
Audio output (2-Channel Audio)
2.0 V (rms),320 ohm, pin jack (L, R) x 1
REPLACING THE FUSES
(Only U.S.A. model)
After correcting the original service problem perform the
following safety check before releasing the set to the customer
Connect the insulating-resistance tester between the plug of
power supply cord and terminal GND on the back panel.
Specifications: More than 10M ohm at 500V
This symbol located near the fuse indicates that the
fuse used is show operating type, For continued protection against
fire hazard, replace with same type fuse , For fuse rating, refer to
the marking adjust to the symbol.
Ce symbole indique que le fusible utilise est e lent.
Pour une protection permanente, n'utiliser que des fusibles de meme
type. Ce demier est indique la qu le present symbol est apposre.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instruction
in the literature accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISOUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
LASER RADIATION WHEN
COVER IS REMOVED.
DO NOT STARE INTO BEAM.
RAYONS LASER QUAND LE
COUVERCLE EST RETIRE. NE PAS
FIXER LE RAYON LASER.
This unit contains a semiconductor laser system and is classified as a
"CLASS 1 LASER PRODUCT". So, to use this model properly
this Instruction Manual carefully.In case of any trouble, please contact
the store where you purchased the unit.To prevent being exposed to the
laser beam, do not try to open the enclosure.
VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
FAILED OR DEFEATED. DO NOT STARE INTO BEAM.
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
The label on the right is
applied on the rear
panel except for USA
and Canadian models.
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser
inside the cabinet.
2. To prevent the laser from being exposed, do not remove the
cover. Refer servicing to qualified personnel.
"CLASS 1 LASER
Pickup Short Land
1.Remove the solder of Laser Diode shorting
Connect Pickup and DVD main circuit PC board by FFC(CP21 and B04).
Fix it with the DVD Mecha
Remove the solder of Laser Diode shorting on Pickup.
2. Factory setting (Initial setting)
2-1 Push the power switch "ON" (Mechanical switch)
2-2 Press the [STOP] and [STANDBY ON] keys at same time, and
it waits until the display of FL tube will be the display of "No Disc" from "Loading".
Turns on the main power supply
Lights in the standby mode.
Stops playing a disc. When disc is playing, if you press
, the disc will start resume play. When
is pressed again
during stop mode, the resume function is canceled.
Begins to play disc (close disc tray first if it is open.)
Temporarily stops playback when a disc is playing. Press this
button again for normal playback.
Press to open or close the disc tray.
Allow you to move to the previous chapter or track / the next
chapter or track on a disc.
Allow you to search in reverse through a disc while it is in play
mode. Each time you press this button, search speed changes.
Toggle for standby on and off