AUDIO VIDEO SURROUND RECEIVER
VR-6070
KRF-X9060D
INSTRUCTION MANUAL
KENWOOD CORPORATION
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this receiver has several
operation modes. These modes enable the remote control to control other audio/video components. In
order to effectively use the remote control it is important to read the operating instructions and obtain
a proper understanding of the remote control and how to switch its operation modes (etc.).
Using the remote control without completely understanding its design and how to switch the operation
modes may result in incorrect operations.
This instruction manual is for some models. Model availability and features
(functions) may differ depending on the country and sales area.
B60-5183-00 01 MA (K, P, T, M, Y, X)
0110
·VR6070/01-09/EN
4/3/02, 12:42 PM
1
2 EN
Units are designed for operation as follows.
U.S.A. and Canada ........................................... AC 120 V only
Australia ........................................................... AC 240 V only
Europe and U.K. ............................................... AC 230 V only
China and Russia ............................................. AC 220 V only
Other countries .......... AC 110-120 / 220-240 V switchable*
For the United Kingdom
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use only a 13-
Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in the
moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted
is not suitable for the power points in your home or the cable is too
short to reach a power point, then obtain an appropriate safety
approved extension lead or adapter, or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse and
dispose of the plug immediately, to avoid a possible shock hazard
by inadvertent connection to the mains supply.
IMPORTANT: The wires in the mains lead are coloured in accordance
with the following code:
Blue
: Neutral
Brown : Live
Do not connect those leads to the earth terminal of a three-pin plug.
Before applying the power
Caution : Read this page carefully to ensure safe
operation.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety precautions
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED
"DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S EN-
CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRI-
ANGLE IS INTENDED TO ALERT THE USER TO THE PRES-
ENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOM-
PANYING THE APPLIANCE.
* AC voltage selection
The AC voltage selector switch on the rear panel is set to the voltage
that prevails in the area to which the unit is shipped.
Before
connecting the power cord to your AC outlet, make sure that the
setting position of this switch matches your line voltage. If not, it
must be set to your voltage in accordance with the following direction.
VOLTAGE SELECTOR
AC 110-
120V~
AC 220-
240V~
Note:
Our warranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector switch.
AC voltage selector switch
Move switch lever to
match your line voltage
with a small screwdriver
or other pointed tool.
·VR6070/01-09/EN
3/26/02, 2:25 PM
2
3 EN
Unpacking
Unpack the unit carefully and make sure that all accessories are present.
FM indoor antenna (1)
AM loop antenna (1)
RF remote antenna (1)
(For VR-6070 only)
For VR-6070
Remote control unit (1)
Batteries (R6/AA) (2)
RC-R0813
For KRF-X9060D
Remote control unit (1)
Batteries (R6/AA) (2)
RC-R0814
For KRF-X9060D
(For the U.K. only)
Remote control unit (1)
Batteries (R6/AA) (2)
RC-R0815
*AC plug adaptor (1)
*Use to adapt the plug on the power
cord to the shape of the wall outlet.
(Accessory only for regions where use
is necessary.)
If any acccessories are missing, or if the unit is damaged or fails to
operate, notify your dealer immediately. If the unit was shipped to you
directly, notify your shipper immediately. Kenwood recommends that
you retain the original carton and packing materials in case you need to
move or ship the unit in the future.
Keep this manual handy for future reference.
Setup code chart (RC-R0813) (VR-6070) and
(RC-R0814) (KRF-X9060D) ............................... 43
Setup code chart (RC-R0815) (KRF-X9060D)
(For the U.K. only) ............................................ 44
CASSETTE deck, CD player & MD recorder
operations ........................................................ 45
Other components' operations ....................... 46
In case of difficulty .......................................... 48
Specifications .................................................. 50
Contents
Caution : Read the pages marked
carefully to ensure
safe operation.
Before applying the power
Before applying the power .............................. 2
Safety precautions ............................................. 2
Unpacking .......................................................... 3
How to use this manual ..................................... 4
Special features ................................................. 5
Names and functions of parts ......................... 6
Main Unit ........................................................... 6
Remote control unit (RC-R0813) (VR-6070) and
(RC-R0814) (KRF-X9060D) ..................................... 7
Remote control unit (RC-R0815) (KRF-X9060D)
(For the U.K. only) .................................................. 8
Setting up the system ........................................ 9
Connecting audio components ........................ 10
Connecting video components ........................ 11
Digital connections .......................................... 12
Connecting video components
(COMPONENT VIDEO) .................................... 13
Connecting a DVD player (6-channel input) ..... 14
Connecting the speakers ................................. 15
Connecting the terminals ................................ 16
Connecting to another room (ROOM B) ......... 17
PRE OUT connections ..................................... 18
Connecting the RF antenna and external
IR Repeater (For VR-6070 only) ....................... 19
Connecting to the AV AUX jacks ..................... 20
Connecting the antennas ................................. 20
Connecting the system control ....................... 21
Preparing the remote control .......................... 22
RF remote control function (For VR-6070 only) .... 22
Preparing for surround sound ....................... 23
Speaker settings .............................................. 23
Normal playback .............................................. 26
Preparing for playback ..................................... 26
Listening to a source component .................... 26
Adjusting the sound ......................................... 27
Recording .......................................................... 29
Recording audio (analog sources) ................... 29
Recording video ............................................... 29
Recording audio (digital sources) .................... 29
Listening to radio broadcasts ....................... 30
Tuning (non-RDS) radio stations ...................... 30
Using RDS (Radio Data System)
(For the U.K. only) ............................................ 30
Presetting radio stations manually .................. 30
Receiving preset stations ................................ 31
Receiving preset stations in order (P.CALL) ... 31
Using the RDS DISP (Display) key
(For the U.K. only) ............................................ 31
Presetting RDS stations (RDS AUTO
MEMORY) (For the U.K. only) ......................... 32
Tuning by Program TYpe (PTY search)
(For the U.K. only) ............................................ 32
Ambience effects ............................................. 33
Surround modes .............................................. 33
Surround play ................................................... 36
DVD 6-channel playback .................................. 37
Convenient functions ....................................... 38
Basic remote control operations for other
components ....................................................... 41
Registering setup codes for other
components ..................................................... 41
Operating other components .......................... 42
Storing the remote control code of
the other components ..................................... 42
Preparations
Operations
Remote Control
Additional
Information
Remote Control
·VR6070/01-09/EN
3/26/02, 2:25 PM
3
4 EN
How to use this manual
This manual is divided into four sections, Preparations, Operations,
Remote Control, and Additional Information.
Preparations
Shows you how to connect your audio and video components to the
receiver and prepare the surround processor.
Since this receiver works with all your audio and video components, we
will guide you in setting up your system to be as easy as possible.
Operations
Shows you how to operate the various functions available on the
receiver.
Remote Control
Shows you how to operate other components using the remote control,
as well as a detailed explanation of all remote control operations. Once
you have registered your components with the proper setup codes, you'll
be able to operate both this receiver and your other AV components (TV,
VCR, DVD player, CD player, etc.) using the remote control supplied with
this receiver.
Additional Information
Shows you additional information such as "In case of difficulty" (trouble-
shooting) and "Specifications".
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft, dry
cloth. Do not use thinner, benzine, alcohol, etc. for these agents may
cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a malfunction. Be
specially careful not to use contact cleaners containing oil, for they
may deform the plastic component.
Before applying the power
Memory back-up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
· Power mode.
· Input selector settings.
· Picture output.
· Speaker ON/OFF.
· Volume level.
· BASS, TREBLE, INPUT level.
· TONE ON/OFF.
· LOUDNESS ON/OFF.
· Dimmer level.
· MD/TAPE settings.
· RF-BAND. (VR-6070 only)
· Listen mode setting.
· Speaker settings.
· SW RE-MIX ON/OFF.
· Distance setting.
· Bass peak level.
· Input mode setting.
· Midnight mode setting.
· PRO LOGIC II mode setting.
· CS II mode setting.
· Broadcast band.
· Frequency setting.
· Preset stations.
· Tuning mode.
· THX mode.
· ACTIVE EQ mode.
· SPEAKER EQ mode.
· DSP mode.
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this equipment
if an unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment may cause
harmful interference to radio communications, if it is not installed and
used in accordance with the instructions. However, there is no guaran-
tee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
FCC Compliance Notice
Audio-video Receiver, VR-6070
These devices comply with Part 15 of FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
KENWOOD U.S.A. CORPORATION
2201 East Dominguez St., Long Beach, CA 90801-5745
Telephone: 310-639-9000
For Canada
IC (Industry Canada) Notice
Operation is subject to the following two conditions: (1) This device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
The term "IC:" before the certification/registration number only
signifies that the Industry Canada technical specifications were met.
For the U.S.A.
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the
point of cable entry as practical.
As an
ENERGY STAR® Partner, Kenwood Corpora-
tion has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
This product can save energy. Saving energy re-
duces air pollution and lowers utility bills.
·VR6070/01-09/EN
3/26/02, 2:25 PM
4
5 EN
Special features
True home theater sound
This receiver incorporates a wide variety of surround modes to bring you
maximum enjoyment from your video software. Select a surround mode
according to your equipment or the software you are going to play and
enjoy!
<
THX Surround EX
THX Surround EX is an extension of THX which was jointly developed
by Lucasfilm THX and Dolby Laboratories. It allows you to experience
a new dimension of depth, spacious ambience and sound localization
to home theater audio.
This system features Re-equalization (Re-EQ), Timbre Matching, Adap-
tive Decorrelation, Bass Peak Level Manager and Loudspeaker Position
Time Synchronization, which reproduces similar cinematic effects in
the home environment.
Dolby Digital and Dolby Digital EX
The DOLBY DIGITAL mode lets you enjoy full digital surround from
software processed in the Dolby Digital format. Dolby Digital provides
up to 5.1 channels of independent digital audio for better sound quality
and more powerful presence than conventional Dolby Surround.
As for Dolby Digital EX, it creates six full-bandwidth output channels
from the 5.1 channel sources. This is done using a matrix decoder that
derives three surround channels from the two in the original recording.
For best results, Dolby Digital EX should be used with movie sound-
tracks recorded with Dolby Digital Surround EX.
Dolby PRO LOGIC II
DOLBY PRO LOGIC II, whilst totally compatible with its predecessor
PRO LOGIC, provides greater advantages in surround sound. It allows
the user to enjoy the conventional stereo or Dolby Surround with a
convincing "5.1 like" presentation. PRO LOGIC II offers special fea-
tures for controlling the overall spatial, dimensionality and frontal sound
field imaging. PRO LOGIC II produces an impressive surround sound
from video software marked
and three-dimensional
space from music CD. When listening to music, you will be able to enjoy
the experience of sheer STEREO surround sound.
DTS-ES
The DTS-ES (Digital Theater System-Extended Surround) is a 6.1-channel
Discrete Surround format which is extended to DTS-ES Discrete 6.1,
DTS-Matrix 6.1 and DTS NEO:6. It is a 6.1 channel expanded from 5.1
surround which includes an additional surround-center channel developed
within surround-left and surround-right. DTS-ES will be able to produce
the original sound recorded similar to the theatrical effects.
In the DTS-ES mode, the 5.1 or 6.1 channel digital input from a DTS CD,
LD or DVD disc (carrying the "DTS" or "DTS-ES" marking) can be
played in Digital Surround.
Important:
When a DTS disc is played on a CD, LD or DVD player, noise may be
output from the analog output. It is recommended that you connect the
digital output of the player to the digital input of this unit.
Multi channel surround sound
(SRS Circle Surround II
)
SRS Circle Surround II TM improves on its predecessor CS-5.1TM result-
ing in the CS-6.1TM system, enabling you to listen to realistic, multi-
channel, surround sound playback from a stereo source or conventional
surround-encoded video source. You already enjoy listening to Dolby
digital sound/DTS multi-channel sound with your multi-speakers. Now
you can listen to audio CDs, MDs, Broadcast and Home Theater using
your multi-speakers. You will discover a new type of sound through
SRS Circle Surround II .
Before applying the power
DSP surround modes
The DSP (Digital Signal Processor) used for this receiver incorporates
a variety of high quality adjustable sound fields, like "ARENA", "JAZZ
CLUB", "THEATER", "STADIUM" and "DISCO". It is compatible with
almost any kind of program source.
DVD 6-channel input
If you own a DVD player equipped with 6-channel output, this receiver
allows you to obtain the full surround sound impact of DVD source
material featuring multi-channel encoding. Since the source signals are
digital and each channel is input independently, the resulting ambience
is far superior to what can be achieved with conventional surround
sound systems.
ACTIVE EQ
ACTIVE EQ mode will produce a more dynamic sound quality in any
condition. You can enjoy a more impressive sound effect when ACTIVE
EQ is turned on during Dolby Digital and DTS playback.
SPEAKER EQ
The SPEAKER EQ function will automatically detect the various features
of each speaker and effectively creates a stereoscopic sound effect.
Remote control
Some of the remote controls have two kinds of signal.
Universal IR (InfraRed) remote control
In addition to the basic receiver, the remote control supplied with this
receiver can also operate almost all of your remote controllable audio
and video components. Just follow the simple setup procedure to
register the components you have connected.
RF remote signal (For VR-6070 only)
You can operate the receiver by sending RF remote signal from the
remote control. The controllable range of the remote control is not
influenced by surroundings such as distance or an obstruction.
RDS (Radio Data System) tuner (For the U.K. only)
The receiver is equipped with an RDS tuner that provides several
convenient tuning functions: RDS Auto Memory, to automatically
preset up to 40 RDS stations broadcasting different programs; station
name display, to show you the name of the current broadcast station;
and PTY search to let you tune stations by program type.
PTY (Program TYpe) search (For the U.K. only)
Tune the stations by specifying the type of program you want to hear.
·VR6070/01-09/EN
3/26/02, 2:26 PM
5