background image
COMPACT COMPONENT SYSTEM
UX-M6V
UX-M6V
No.21053
Dec. 2001
COPYRIGHT
2001 VICTOR COMPANY OF JAPAN, LTD.
SERVICE MANUAL
Contents
Safety precautions
Preventing static electricity
Important for laser products
Disassembly method
Adjustment method
Flow of functional operation
until TOC read
1-2
1-3
1-4
1-5
1-15
1-19
1-20
1-20
1-21
1-22
1-40
Maintenance of laser pickup
Replacement of laser pickup
Trouble shooting
Description of major ICs
Wiring connections
Area suffix
US ---------------------- Singapore
UB --------------------- Hong Kong
DISPLAY
MIC
PROGRAM
REC
DIRECTION
PLAY/PAUSE
VOLUME
STOP/CLEAR
DEMO
SEARCH/TUNING
SHUFFLE
CD
TUNER
TAPE
BAND
REV. MODE
MICR O
COMPONENT
SYSTEM
UX-M6V
A U T O REVERSE
FULL LOGIC DECK
FM MODE
/VOCAL
EJECT
OSD/DIM
PRESET
PRE EQ
/BBS
REPEAT
TIMER
ON/OFF
SET
OPEN
/CLOSE
STANDBY
/ON
CD/SHUFFLE
TUNER
/BAND
TAPE
/REV.MODE
OSD/DIM
PROGRAM
REC
DISPLAY
123
REPEAT
/DEMO
FM MODE
/VOCAL
456
7
8
9
MIC/ECHO
0
NTSC/PAL
+10
MUTING
BEAT CUT
/KEY
STANDBY/ON
PBC
GOTO
A-B
RESUME
VOLUME
+
Ð
SLOW
TIMER
VIEW
PRE EQ/BBS
RM-SUXM6V REMOTE CONTROL
SP-UXM6V
CA-UXM6V
SP-UXM6V


background image
UX-M6V
1-2
1. This design of this product contains special hardware and many circuits and components specially for safety
purposes. For continued protection, no changes should be made to the original design unless authorized in
writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services
should be performed by qualified personnel only.
2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product
should not be made. Any design alterations or additions will void the manufacturer`s warranty and will further
relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.
3. Many electrical and mechanical parts in the products have special safety-related characteristics. These
characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily
be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in the Parts List of Service Manual. Electrical
components having such features are identified by shading on the schematics and by (
) on the Parts List in
the Service Manual. The use of a substitute replacement which does not have the same safety characteristics
as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or
other hazards.
4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be
separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of
electric shock and fire hazard. When service is required, the original lead routing and dress should be
observed, and it should be confirmed that they have been returned to normal, after re-assembling.
5. Leakage currnet check (Electrical shock hazard testing)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the product
(antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the
product is safe to operate without danger of electrical shock.
Do not use a line isolation transformer during this check.
Plug the AC line cord directly into the AC outlet. Using a "Leakage Current Tester", measure the leakage
current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return
path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
Alternate check method
Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more
sensitivity in the following manner. Connect a 1,500
10W resistor paralleled by a 0.15 F AC-type capacitor
between an exposed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal part,
particularly any exposed metal part having a return path to
the chassis, and meausre the AC voltage across the resistor.
Now, reverse the plug in the AC outlet and repeat each
measurement. Voltage measured any must not exceed 0.75 V
AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.).
1. This equipment has been designed and manufactured to meet international safety standards.
2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
3. Repairs must be made in accordance with the relevant safety standards.
4. It is essential that safety critical components are replaced by approved parts.
5. If mains voltage selector is provided, check setting for local voltage.
Good earth ground
Place this
probe on
each exposed
metal part.
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
1500
10W
0.15 F AC TYPE
!
Burrs formed during molding may
be left over on some parts of the
chassis. Therefore, pay attention to
such burrs in the case of
preforming repair of this system.
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor (
), diode (
) and ICP (
) or identified by the " "
mark nearby are critical for safety.
(This regulation does not correspond to J and C version.)


background image
UX-M6V
1-3
Short land
CD/Video pickup unit
Connector
Conductive material
(conductive sheet) or iron plate
(caption)
Anti-static wrist strap
5. Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD/Video pickup unit.
Apply solder to the short land before the card wire is disconnected from
the connector on the CD/Video pickup unit.
(If the card wire is disconnected without applying solder, the CD/Video
pickup may be destroyed by static electricity.)
In the assembly, be sure to remove solder from the short land after
connecting the card wire.
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged,
can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
Preventing static electricity
1. Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
2. About the earth processing for the destruction prevention by static electricity
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it
before placing the traverse unit (optical pickup) on it.
2-1 Ground the workbench
2-2 Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
In order to maintain quality during transport and before installation, both sides of the laser diode on the
replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power
source can easily destroy the laser diode.
3. Handling the optical pickup
1.
2.
Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
Remove solder of the short land on the card wire after replacing the optical pickup. For specific details, refer to
the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit.
Be careful not to take too long a time when attaching it to the connector.
Handle the card wire carefully as it may break when subjected to strong force.
It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
4. Handling the traverse unit (optical pickup)
1.
2.
3.
4.


background image
UX-M6V
1-4
Rear panel inside
Important for laser products
1.CLASS 1 LASER PRODUCT
2.DANGER : Invisible laser radiation when open and inter
lock failed or defeated. Avoid direct exposure to beam.
3.CAUTION : There are no serviceable parts inside the
Laser Unit. Do not disassemble the Laser Unit. Replace
the complete Laser Unit if it malfunctions.
4.CAUTION : The compact disc player uses invisible
laserradiation and is equipped with safety switches
whichprevent emission of radiation when the drawer is
open and the safety interlocks have failed or are de
feated. It is dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
VARNING : Osynlig laserstrålning är denna del är öppnad
och spårren är urkopplad. Betrakta ej strålen.
VARO
: Avattaessa ja suojalukitus ohitettaessa olet
alttiina näkymättömälle lasersäteilylle.Älä katso
säteeseen.
ADVARSEL : Usynlig laserstråling ved åbning , når
sikkerhedsafbrydere er ude af funktion. Undgå
udsættelse for stråling.
ADVARSEL : Usynlig laserstråling ved åpning,når
sikkerhetsbryteren er avslott. unngå utsettelse
for stråling.
REPRODUCTION AND POSITION OF LABELS
WARNING LABEL
CLASS 1
LASER PRODUCT
! CAUTION Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
DANGER-Invisible laser radiation
when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.
VORSICHT-Unsichtbare Laserstrahlung,
wenn Abdeckung geoffnet und
Sicherheitsverriegelung uberbruckt.
ü
Nicht dem Straht aussetzen.
ADVARSEL:USYNLIG LÅ SERSTRALING
VED Å BNING,NÅ R SIKKERHEDSAF-
BRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSA TTELSE FOR STRÅ LING.
VARO! Avattaessa ja suojalukitus ohitettaessa
olet alttiina nadkmaton lasersateilylle.
Äla katso säateesen.
ä
VARNING!Osymlig laserstralning nar denna
åä
del ar osppad och sparren ar urkopplad.
ää
ä
Betraka ej stralen.
å
ADVERSEL! Usynilig laserstraling nar
deksel apnes og slikkerhedslas brytes.
Unnga eksponering for siralen.
A pleine puissance.I ecoute prolongee du
baladeur peut endommager l'oreille de
l'utilisaleur.
DANGER-Invisible laser radiation
when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.
VORSICHT-Unsichtbare Laserstrahlung,
wenn Abdeckung geoffnet und
Sicherheitsverriegelung uberbruckt.
ü
Nicht dem Straht aussetzen.
ADVARSEL:USYNLIG LÅ SERSTRALING
VED Å BNING,NÅ R SIKKERHEDSAF-
BRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSA TTELSE FOR STRÅ LING.
VARO! Avattaessa ja suojalukitus ohitettaessa
olet alttiina nadkmaton lasersateilylle.
Äla katso säateesen.
ä
VARNING!Osymlig laserstralning nar denna
åä
del ar osppad och sparren ar urkopplad.
ää
ä
Betraka ej stralen.
å
ADVERSEL! Usynilig laserstraling nar
deksel apnes og slikkerhedslas brytes.
Unnga eksponering for siralen.
A pleine puissance.I ecoute prolongee du
baladeur peut endommager l'oreille de
l'utilisaleur.


background image
UX-M6V
1-5
Fuse(F901)
1.6A 250V
Fuse(F903)
1.6A 250V
Fuse(F904)
500mA 250V
Power supply IC
(IC902)
Power supply IC
(IC902)
Cassis
Heat sink
Soldered part a
Soldered part b
A
Power supply
board
Power supply board
Fuse(F902)
2A 250V
Fig.1
Fig.2
Fig.3
Main board
Power amplifier IC
(IC802)
Replacing the fuses
(See Fig. 1.)
<Main body section>
Remove the left side panel according to its
disassembly method (see Figs. 7 and 8).
Fuses are located inside the left side panel.
Disassembly method
Fuse Replacement for the power supply IC and
power amplifier IC
[Caution] Be sure to replace the required fuses
with designated ones.
Replacing the power supply IC on the
power supply board
(See Figs. 1 and 2.)
1.
2.
Remove the left side panel and power supply board
according to their disassembly methods (see Figs.
7, 8, 18 and 19).
The power supply IC is located below the power
supply board.
In order to replace the power supply IC, remove the
solder from the soldered part a.
Replacing the power amplifier IC on
the main board
(See Fig. 3.)
1.
2.
Remove
the
main
board
according
to
its
disassembly method (see Figs. 20 and 21).
Remove the two screws A that attach the power
amplifier IC onto the heat sink.
In order to replace the power amplifier IC, remove
the solder from soldered part b on the back side of
the main board.