JVC SP-F303EU - Owner's Manual Immediate Download

English

LVT1047-001A

[E]

SP-F303

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D'INSTRUCTIONS

GEBRUIKSAANWIJZING

MANUAL DE INSTRUCCIONES

ISTRUZIONI

BRUKSANVISNING

VEJLEDNING

KÄYTTÖOHJE

INSTRUKCJA OBSLUGI

SATELLITEN-LAUTSPRECHER-SYSTEM

SYSTEME HAUT-PARLEURS SATELLITE

SATELLIET LUIDSPREKERSYSTEEM

SYSTEMA DE ALTAVOZ DE SATÉLITE

SISTEMA DI ALTOPARLANTI SATELLITI

SATELLITHÖGTALARSYSTEM

SATELLIT HØJTTALERSYSTEM

SATELLIITTIKAIUTINJÄRJESTELMÄ

SYSTEM GLONIKÓW SATELITARNYCH

KÜLS HANGFALRENDSZER

SATELITNÍ REPRODUKTOROVÁ SOUSTAVA

SATELLITE SPEAKER SYSTEM

-- Consists of SP-F303F and SP-F303C

Bestehend aus SP-F303F und SP-F303C

Se compose de SP-F303F et SP-F303C

Bestaat uit SP-F303F en SP-F303C

Consta de SP-F303F y SP-F303C

L'impianto è formato da SP-F303F e SP-F303C

Består av SP-F303F och SP-F303C

Består of SP-F303F og SP-F303C

Sisältää seuraavat osat: SP-F303F ja SP-F303C

Zestaw przyrzadów SP-F303F a SP-F303C

A készülék SP-F303F és SP-F303C egységekbl áll

Sestava komponent SP-F303F a SP-F303C

SP-F303F SP-F303C

HASZNÁLATI UTASÍTÁS

PÍRUCKA OBSLUZE

#SP-F303-E-p01-6.p65

01/16/3, 7:35 pm

· To improve the sound field

If the speakers are facing a solid wall or glass

door, etc., it is recommended to furnish the wall

with materials that absorb sounds, for example

by hanging up thick curtains, to prevent

reflections and standing waves.

· To use the speakers without any trouble

Do not reproduce sounds at so high a volume that they

are distorted; otherwise, the speakers may be damaged

by internal heat buildup.

When moving the speakers, do not pull the speaker cords;

otherwise, the speakers may fall over, causing damage or

injury.

When holding a satellite speaker, do not grasp the

speaker (upper) portion, but always grasp the leg (lower)

portion of the satellite speaker.

Checking the supplied Accessories

Check to be sure you have the following supplied accessories.

The number in parenthesis indicates the quantity of the piece

supplied.

· Speaker cords

· Screws (with washer)

M4 x 25 mm (16)

If any of the items above are missing, contact your dealer

immediately.

Speaker and Speaker cords--

to improve the sound quality

When connecting the speaker cords

Make sure to match the polarity (

ª and ·); otherwise,

the sound will lose the surround effect.

After connecting, check that the exposed cores are fully

inserted into the terminal.

When using other speaker cords

Observe the following;

· Buy thick speaker cords rather than thin cords, and make

them as short as possible for connection.

· Use speaker cords of the same length for both left and

right speakers.

· Do not use long speaker cords; otherwise, the sound

quality may deteriorate.

Contents

Page

Warnings, Cautions and Others ......................................... 1

Assembly ........................................................................... 2

Connection ......................................................................... 5

General Layout of Speakers .............................................. 6

Specifications ..................................................................... 6

Thank you for purchasing a JVC speaker system.

Before you begin using these speakers, please read the

instructions carefully to be sure you get the best possible

performance. If you have any questions, consult your JVC

dealer.

Warnings, Cautions and

Others

5 Precautions for installation

· Do not install the speakers on an uneven surface or in a

place subject to vibration; otherwise, they may fall over,

causing damage or injury.

Take the occurrence of earthquakes or other

physical shocks into consideration when

selecting the installation place, and secure

the speakers thoroughly.

· To prevent deformation or discoloration of the

cabinet, do not install the speakers where they

are exposed to direct sunlight or high humidity,

and avoid installation near air conditioning

outlets.

· Speaker vibrations may cause howling. Place

the speakers as far away from the player as

possible.

· The speakers are magnetically shielded to avoid color

distortions on TVs. However, if not installed properly, it may

cause color distortions. So, pay attention to the following

when installing the speakers.

When placing the speakers near a TV set, turn off the

TV's main power switch or unplug it before installing the

speakers.

Then wait at least 30 minutes before turning on the TV's

main power switch again.

Some TVs may still be affected even though you have

followed the above. If this happens, move the speakers

further away from the TV.

· Tuner reception may become noisy or hissing if a speaker is

installed near the tuner. In this case, leave more distance

between the tuner and the speakers or use an outdoor

antenna for better tuner reception without interference from

the speakers.

5 Precautions for Daily Use

· To maintain the appearance of the speakers

Wipe with a dry, soft cloth if the cabinet or control panel

should become dirty.

If very dirty, apply a small amount of water or neutral

detergent to the cloth and wipe clean, then wipe with a dry

cloth.

Approx. 5 m (3);

For satellite speakers for front left/

right channel and center speaker

Approx. 10 m (2);

For satellite speakers for surround

left/right channel

#SP-F303-E-EN.p65

02/03/3, 2:58 pm

English

5 Assembling the satellite speakers

Each speaker (except the center speaker) has been divided

into two parts for shipment. Before using this speaker system,

assemble it first by following the procedure below.

· Prepare a Phillips screw driver.

Before assembling--

· Take care not to drop the stand while assembling;

otherwise, it may cause damage to the floor or injury.

· Ensure enough space for assembly and installation.

· Place a large, thick cloth on the floor where you

assemble the speaker, so you can protect the floor and

the speaker itself.

· Use the speaker only after assembly is fully and

correctly done.

1 Connect the speaker connecters to the

stand connecters.

2 Join the stand to the speaker section.

3 Fix the stand to the speaker section.

· Be sure to tighten the screws firmly.

Cushion (not supplied)

Assembly

Speaker

section

Stand

To be continued on the next page

It is recommended to place a cushion under the speaker

section.

· You can tighten the screws easily by placing the

speaker section horizontally.

Speaker section

Stand

Screw (4)

(Supplied, M4 x 25 mm)

Rear

Front

Speaker connectors

Speaker section

Stand

#SP-F303-E-EN.p65

02/03/3, 2:58 pm

4 Connect the speaker cord to the speaker

terminal.

· Each speaker can be used as front or surround speaker.

Use the 5-meter speaker cords for front speakers and

10-meter speaker cords for surround speakers.

Twist and pull the

insulation coat to

remove.

Black

5 Route the speaker cord as shown below.

· Be sure to take out the slack so that the speaker cord lies

flat.

Repeat the procedure from step 1 to assemble the other

satellite speakers.

Press and hold the

clamp.

Insert the exposed

core of the speaker

cord fully into the

terminal.

Release your finger.

Black

White

Assembly (continued)

White

#SP-F303-E-EN.p65

02/03/3, 2:58 pm

English

5 Connecting the Center speaker

· To connect the center speaker, use the same type of

speaker cord (5 m; tagged with "CENTER") as used for

connecting the front speakers.

Insert the speaker cord into the speaker

terminal.

Black

Press and hold

the clamp.

Insert the exposed

core of the speaker

cord fully into the

terminal.

Release your finger.

Black

White

Make sure to match the polarity (

ª and ·); otherwise,

the sound will lose the surround effect.

After connecting, check that the exposed cores are fully

inserted into the terminal.

White

#SP-F303-E-EN.p65

02/03/3, 2:58 pm