background image
SERVICE MANUAL
COPYRIGHT © 2005 Victor Company of Japan, Limited
No.MA134
2005/4
CD RECEIVER
MA134
2005
4
KD-G311,KD-G312,KD-G317
TABLE OF CONTENTS
1
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
4
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25
5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26
KD-G311
KD-G317
KD-G312
STEERING CABLE
CONTROL PANEL
BLACK
BLACK
SILVER
Area suffix
EE -------- Russian Federation
KD-G317
KD-G311,KD-G312
Area suffix
E ------------ Southern Europe
EX ------------ Northern Europe
EY ------------- Eastern Europe
KD-G311,KD-G312
EU ------------------------- Turkey
KD-G317


background image
1-2 (No.MA134)
SPECIFICATION
· Design and specifications are subject to change without notice.
· Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/
or other countries.
AUDIO AMPLIFIER SECTION
Maximum Power Output
Front
50 W per channel
Rear
50 W per channel
Continuous Power Output (RMS) Front
19 W per channel into 4
, 40 Hz to 20 000 Hz at no more
than 0.8% total harmonic distortion.
Rear
19 W per channel into 4
, 40 Hz to 20 000 Hz at no more
than 0.8% total harmonic distortion.
Load Impedance
4
(4 to 8 allowance)
Tone Control Range
Bass
±10 dB at 100 Hz
Treble
±10 dB at 10 kHz
Frequency Response
40 Hz to 20 000 Hz
Signal-to-Noise Ratio
70 dB
Line-Out Level/Impedance
2.5 V/20 k
load (full scale)
Output Impedance
1 k
Other Terminal
Steering wheel remote input (KD-G311,KD-G312)
TUNER SECTION
Frequency Range
FM
87.5 MHz to 108.0 MHz
FM1/FM2 (KD-G317)
87.5 MHz to 108.0 MHz
FM3 (KD-G317)
65.00 MHz to 74.00 MHz
AM
(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
FM Tuner
Usable Sensitivity
11.3 dBf (1.0
µV/75 )
50 dB Quieting Sensitivity
16.3 dBf (1.8
µV/75 )
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response
40 Hz to 15 000 Hz
Stereo Separation
30 dB
Capture Ratio
1.5 dB
MW Tuner
Sensitivity
20
µV
Selectivity
35 dB
LW Tuner
Sensitivity
50
µV
CD PLAYER SECTION
Type
Compact disc player
Signal Detection System
Non-contact optical pickup (semiconductor laser)
Number of Channels
2 channels (stereo)
Frequency Response
5 Hz to 20 000 Hz
Dynamic Range
96 dB
Signal-to-Noise Ratio
98 dB
Wow and Flutter
Less than measurable limit
MP3 Decoding Format
MPEG1/2 Audio Layer 3
Max. Bit Rate: 320 kbps
WMA (Windows Media Audio) Decoding Format
Max. Bit Rate: 192 kbps
GENERAL
Power Requirement
Operating Voltage
DC 14.4 V (11 V to 16 V allowance)
Grounding System
Negative ground
Allowable Operating Temperature
0
°C to +40°C
Dimensions (W
× H × D)
Installation Size (approx.)
182 mm
× 52 mm × 150 mm
Panel Size (approx.)
188 mm
× 58 mm × 11 mm
Mass (approx.)
1.3 kg (excluding accessories)


background image
(No.MA134)1-3
SECTION 1
PRECAUTIONS
1.1
Safety Precautions
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
!
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.


background image
1-4 (No.MA134)
1.2
Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1
Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(3) Handling the optical pickup
· In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
· Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3
Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4
Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the CD pickup unit.
· Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.
(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)
· In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
1M
(caption)
Anti-static wrist strap
Conductive material
(conductive sheet) or iron plate
Pickup
Short-circuit point
(Soldering)
Flexible wire


background image
(No.MA134)1-5
1.5
Important for laser products
1.CLASS 1 LASER PRODUCT
2.DANGER : Invisible laser radiation when open and inter
lock failed or defeated. Avoid direct exposure to beam.
3.CAUTION : There are no serviceable parts inside the
Laser Unit. Do not disassemble the Laser Unit. Replace
the complete Laser Unit if it malfunctions.
4.CAUTION : The CD,MD and DVD player uses invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
REPRODUCTION AND POSITION OF LABELS
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
WARNING LABEL
CAUTION : Visible and Invisible
laser radiation when open and
interlock
failed
or
defeated.
AVOID DIRECT EXPOSURE TO
BEAM.
(e)
VARNING
:
Synlig
och
osynling laserstrålning när
den öppnas och spärren är
urkopplad.
Betrakta
ej
strålen.
(s)
VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle
ja
näkymättömälle
lasersäteilylle.
Vältä
säteen
kohdistumista suoraan itseesi. (f)
ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling.
(d)
CLASS 1
LASER PRODUCT