background image
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
INPUT CARD FOR A JVC MONITOR
BEDIENUNGSANLEITUNG:
EINGANGSKARTE FÜR JVC MONITORE
MANUEL D'INSTRUCTIONS:
CARTE D'ENTRÉE POUR MONITEURS JVC
ISTRUZIONI:
SCHEDA DI INGRESSO PER MONITOR JVC
MANUAL DE INSTRUCCIONES: TARJETA DE ENTRADA PARA UN MONITOR JVC
JVC
IF-CF01CMG
COMPONENT/RGB INPUT CARD
IF-CF01RBG
COMPONENT/RGB ACTIVE THROUGH CARD
IF-CF21HDG
HD/SD SDI INPUT CARD
LCT1973-001A
INSTRUCTIONS
cover.p65
05.11.14, 3:05 PM
3


background image
1
ENGLISH
INPUT CARD FOR A JVC MONITOR
IF-CF01CMG
COMPONENT/RGB INPUT CARD
IF-CF01RBG
COMPONENT/RGB ACTIVE THROUGH CARD
IF-CF21HDG
HD/SD SDI INPUT CARD
INSTRUCTIONS
01_EN_LCT1973-01A-f.p65
05.11.18, 13:05
1


background image
2
FCC NOTICE
7 For IF-CF01CMG and IF-CF01RBG
CAUTION: Changes or modifications not approved by JVC could void the user 's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
­ Reorient or relocate the receiving antenna.
­ Increase the separation between the equipment and receiver.
­ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
­ Consult the dealer or an experienced radio/TV technician for help.
7 For IF-CF21HDG
CAUTION: Changes or modifications not approved by JVC could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
EMC Supplement (For IF-CF21HDG only)
This equipment is in conformity with the provisions and protection requirements of the
corresponding European Directives. This equipment is designed for professional video appliances
and can be used in the following environments:
· Controlled EMC environment (for example purpose built broadcasting or recording studio), and
the rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)
These input cards are only for use with specific monitors.
Consult your dealer for the compatible monitors.
Precautions
Before installing this Input Card in your monitor, please read the Safety
Precautions included in your monitor's user manual.
Thank you for purchasing this JVC Input Card. In order to take full advantage of the
card's capabilities, please read and follow all instructions carefully before installing
and using the card. Retain this booklet for future reference.
EUROPE EMC STANDARD NOTICE (For IF-CF21HDG only)
Warning: This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measure.
01_EN_LCT1973-01A-3b.p65
05.10.25, 20:59
2


background image
3
ENGLISH
Attention:
This symbol is
only valid in the
European
Union.
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your local municipal office, your household waste disposal service
or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
01_EN_LCT1973-01A-3b.p65
05.10.25, 20:59
3


background image
4
Before Installation
7 Accessaries
· Label (x 1):
For placing to the rear panel and the remote control of the monitor after installing
the Input Card.
· Slot cover* (x 1): For covering the blank slot.
* Not supplied for IF-CF01RBG
7 Preparation
·Wear gloves to protect your hands from metal parts on the Input Card's board.
·You will need a 6 mm Phillips screwdriver.
·Turn off the monitor's main power and unplug the power cable from the AC outlet.
· Place the monitor with its LCD panel side down on a soft cloth so as not to damage the LCD panel.
7 Cautions
· Do not touch the terminals or board pattern of the Input Card to keep it from being damaged by
static electricity.
· Do not damage the Input Card's connection terminal.
· Do not put anything into the Input Card's holes or intakes.
· Do not force the Input Card into the monitor's slot.
· Attach the slot cover on the monitor's slot in which no Input Card is installed.
· Attach the Input Card before mounting the monitor on the stand or wall mounting unit.
Installation
7 Installation procedure
1. Remove the slot cover from the
slot on the bottom side of the
monitor.
The monitor in the illustration is GM-H40L1G.
Slot cover
01_EN_LCT1973-01A-3b.p65
05.10.25, 20:59
4