ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SDI INPUT CARD
INPUT CARD FOR A JVC MONITOR
BEDIENUNGSANLEITUNG:
SDI-EINGANGSKARTE
MANUEL D'INSTRUCTIONS:
CARTE D'ENTRÉE SDI
ISTRUZIONI:
SCHEDA DI INGRESSO SDI
MANUAL DE INSTRUCCIONES: TARJETA DE ENTRADA SDI
:
TARJETA DE ENTRADA PARA UN MONITOR JVC
SCHEDA DI INGRESSO PER MONITOR JVC
CARTE D'ENTRÉE POUR MONITEURS JVC
EINGANGSKARTE FÜR JVC MONITORE
LCT1965-001A
INSTRUCTIONS
IF-C21SD1G
IF-C51SD1G (compatible with AUDIO LEVEL METER)
LCT1965-001A_cover-f.p65
06.1.5, 19:34
3
ENGLISH
1
SDI INPUT CARD
IF-C21SD1G
IF-C51SD1G (compatible with AUDIO LEVEL METER)
INPUT CARD FOR A JVC MONITOR
INSTRUCTIONS
EN_LCT1965-001A_f.p65
06.1.5, 19:33
1
2
Thank you for purchasing this JVC Input Card. In order to take full advantage of the
card's capabilities, please read and follow all instructions carefully before installing
and using the card. Retain this booklet for future reference.
Precautions
Before installing this Input Card in your monitor, please read the Safety
Precautions included in your monitor's user manual.
FCC NOTICE (U.S.A. only)
CAUTION: Changes or modifications not approved by JVC could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
EMC Supplement (Europe only)
This equipment is in conformity with the provisions and protection requirements of the
corresponding European Directives. This equipment is designed for professional video appliances
and can be used in the following environments:
· Controlled EMC environment (for example purpose built broadcasting or recording studio), and
rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)
These input cards are only for use with specific monitors.
Consult your dealer for the compatible monitors.
EN_LCT1965-001A_f.p65
06.1.5, 19:33
2
ENGLISH
3
Information for Users on Disposal of Old Equipment
[European Union]
This symbol indicates that the electrical and electronic equipment should not be
disposed as general household waste at its end-of-life. Instead, the product should
be handed over to the applicable collection point for the recycling of electrical and
electronic equipment for proper treatment, recovery and recycling in accordance
with your national legislation.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health which could otherwise be caused by inappropriate waste handling of this
product. For more information about collection point and recycling of this product,
please contact your local municipal office, your household waste disposal service
or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
(Business users)
If you wish to dispose of this product, please visit our web page
www.jvc-europe.com to obtain information about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in accordance with applicable
national legislation or other rules in your country for the treatment of old electrical
and electronic equipment.
Setting DIP Switches
In the following cases, change the DIP switch settings before installing the input card into
the monitor:
·To switch the audio input type
· When your monitor does not have the buttons or menu for EMBEDDED AUDIO channel
selection
· When your monitor does not have the buttons or menu for AUDIO LEVEL METER setting
(only when using IF-C51SD1G)
CAUTION
· The DIP switch setting cannot be changed after the input card is installed into the monitor's slot.
Make sure to change the switch settings before installing the input card.
·Wear gloves to protect your hands from metal parts on the Input Card's board.
· Do not touch the terminals or board pattern of the Input Card to prevent them from being damaged
by static electricity.
Attention:
This symbol is
only valid in the
European
Union.
EN_LCT1965-001A_f.p65
06.1.5, 19:33
3
4
Setting DIP Switches (continued)
S0401
S0402
[1] [2] [3] [4] [5] [6] [7] [8]
Using DIP switches
Make the settings you want by following the
descriptions of each switch (1 4).
· The diagram on the right shows all switches
are set to OFF (factory setting).
·Peel off the film on the switches when
changing the setting.
*1 IF-C51SD1G only
*2 Switches [7] and [8] of S0401 do not function for
IF-C21SD1G.
*Audio signal input to the AUDIO IN terminal
DIP switches
S0401
DIP switches
S0402*1
Connection
terminal
1 Selecting the audio input type
Select the analog audio input or EMBEDDED AUDIO input to be output from the
monitor's speaker. This setting is valid regardless of the setting 2.
Setting
Switch No.
S0401 [1]
Analog audio input*
ON
EMBEDDED AUDIO
OFF
· When the audio input type is set to analog audio input, no signal is output from the E.AUDIO
MONITOR OUT terminal. (AUDIO LEVEL METER display is also not available.)
· In the following cases, settings 2 to 4 are not required. See page 8 and install the input card to
the monitor.
When analog audio input is selected.
When your monitor has the buttons or menu for EMBEDDED AUDIO channel selection.
When your monitor has the buttons or menu for AUDIO LEVEL METER setting.
2 Activating DIP switch
Set DIP switch setting to enable or disable.
Setting
Switch No.
S0401 [2]
Activate DIP switch
ON
Deactivate DIP switch
OFF
· When "OFF" is selected, settings 3 and 4 are not required. See page 8 and install the input
card to the monitor.
· When "ON" is selected, EMBEDDED AUDIO channel selection and AUDIO LEVEL METER
setting cannot be changed from the monitor.
EN_LCT1965-001A_f.p65
06.1.5, 19:33
4