background image
OUT
IN
RF OUT
ANT.IN
AUDIO
R
L
VIDEO
VIDEO CASSETTE PLAYER
HR-P500K/P100A
Thank you for purchasing this JVC video cassette player. To ensure optimum performance
of this unit, please read this instruction manual thoroughly.
INSTRUCTIONS
English
PAL NTSC
7 Only cassettes marked "VHS" can be used with this video cassette player.
2 Automatic features
Auto power on
The video cassette player is automatically
turned on when the tape is inserted.
Auto rewind
The video tape is automatically rewound
when the end of the tape is reached during
the play, recording or shuttle search forward
mode.
Auto playback
If the video cassette's safety tab has been
removed, playback will begin automatically
when the tape is inserted into the video
cassette player.
Power off eject
Even when the video cassette player's
power is off, pressing the eject button will
turn the power on and eject the tape. Once
ejected, the power will be turned off again
automatically.
Auto head cleaning
When a tape is loaded or ejected the VCP
video head is cleaned automatically.
1 Features
· 3 system (PAL/MESECAM/NTSC)
· NTSC playback (on PAL television)
· RF output G/K switchable
· Digital auto tracking
· HQ (High Quality)
· Auto playback function
· Repeat playback
· Shuttle search
· Still and slow motion
· Line recording
· Karaoke (HR-P500K only)
· B.E.S.T.(BiconditionalEqualizedSignal
Tracking) picture system
3 Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE IN-SIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
The STANDBY/ON
button does not completely shut off mains power from the unit,
but switches operating current on and off.
This unit is produced to comply with Standard IEC 60065.
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space
on all sides to allow for ventilation (10 cm or more on both side, on top and at the rear.)
When discarding batteries, environmental problems must be considered and the local rules
or laws governing the disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the player, remote
control or video cassette player.
1. DO NOT place the player . . .
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the player's ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may
not be able to get out.)
3. DO NOT place heavy objects on the player or remote control.
4. DO NOT place anything which might spill on top of the player or remote control.
If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place
any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.
8. AVOID violent shocks to the player during transport.
Beware of moisture condensation
Moisture in the air will condense on the VCP when you move it from a cold place to a warm
place, or under extremely humid conditions -- just as water droplets form on the surface of
a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to
the tape. In conditions where condensation may occur, keep the VCP's power turned on for
a few hours to let the moisture dry.
When transporting
7 Be sure to remove cassette from VCP before packing.
7 Avoid violent shocks to the VCP during packing and transport.
4 Controls
Front panel
1
1
1
1
1
STANDBY/ON
button
To turn the power on and off (standby mode).
2
2
2
2
2
Cassette loading slot
Load the video cassette here.
3
3
3
3
3
Rewind
1
1
1
1
1 button
To rewind the video tape and to start reverse shuttle search playback mode.
4
4
4
4
4
Play
#
#
#
#
# button
To start playback.
5
5
5
5
5
Fast forward
¡
¡
¡
¡
¡ button
To fast forward the video tape and to start forward shuttle search playback mode.
6
6
6
6
6
SP / LP / EP button
To select the recording tape speed.
7
7
7
7
7
Stop/Eject
§
§
§
§
§ button
To stop playback and to eject the video tape.
8
8
8
8
8
Record
¶ button
To start recording.
9
9
9
9
9
OSD button
To display the information on the television's display.
0
0
0
0
0
Remote sensor window
For remote control operation.
!
!
!
!
!
STANDBY / REC indicator
·
Lights when the power turns off (Standby mode) or during recording mode.
·
Blinks during recording pause mode.
@
@
@
@
@
POWER-ON indicator
Lights when the power turns on.
#
#
#
#
#
MIC input terminals (HR-P500K only)
Rear panel
1
1
1
1
1
AC power cord
2
2
2
2
2
RF. OUT terminal
3
3
3
3
3
AUDIO/VIDEO IN terminals
4
4
4
4
4
AUDIO/VIDEO OUT terminals
5
5
5
5
5
ANT. IN terminal
The video cassette player illustrations appearing in this instruction manual are of the HR-P500K.
HR-P500K
HR-P100A
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
SUPER
HEAD CLEANER
Hi-Fi Karaoke
STANDBY/ON
MIC
2
1
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
LONGPLAY RECORDING AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
SUPER
HEAD CLEANER
STANDBY/ON
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
OUT
IN
RF OUT
ANT.IN
AUDIO
R
L
VIDEO
OUT
IN
RF OUT
ANT.IN
AUDIO
L
VIDEO
Rear panel
HR-P500K
HR-P100A
5 Wireless remote control
When using the remote control for operation of the video cassette player, make sure that it
is pointed at the remote sensor window.
You can also use the player's remote control to operate a JVC television.
!
!
!
!
!
STANDBY/ON
button
To turn the power on and off (standby
@
@
@
@
@
TRACKING ­/+ buttons
To adjust tracking during playback.
#
#
#
#
#
0000 /
button
To reset the tape counter.
$
$
$
$
$
FF
¡
¡
¡
¡
¡
button
To fast forward the video tape. Also to
start forward shuttle search playback.
%
%
%
%
%
8
8
8
8
8 PAUSE button
To freeze the picture during playback.
Also to engage the recording pause
mode.
^
^
^
^
^
2/3 buttons
To set the mode.
TV
+/­ (TV Volume) buttons
To adjust the TV volume.
&
&
&
&
&
OK/OSD button
· To fix the setting.
· To display the information on the
television's display.
*
*
*
*
*
¶ REC button
Press the
¶ REC and 3
3
3
3
3 PLAY but-
tons together, to start recording.
Operating JVC TVs
Buttons with a small dot on the left side of
the name can also be used to operate your
JVC TV while holding down TV.
To operate your TV, while holding down TV,
press the corresponding button:
, TV/
VCR, TV PR +/­, TV
+/­ (TV Volume),
(TV Muting),
(TV Sounds).
Notes:
· Point the remote control toward the
remote sensor window.
· The maximum operating distance of
the remote control is about 8 m.
· When inserting the batteries, be sure to
insert in the correct directions as indi-
cated under the battery cover.
· If the remote control doesn't work properly,
remove its batteries, wait a short time,
replace the batteries and then try again.
7 Connections
Make sure that the power to the video cassette player and TV is off before making the
following connections.
Connection B
Connection A
Note:
If you put a TV set directly on this Video cassette player or install it too close to a TV set,
noise may occur. If this noise occurs, separate the Video cassette player and the TV set.
Connection A (basic)
In order to use the video cassette player it must be connected between the antenna and the
TV.
Connect your TV antenna cable to the video cassette player's ANT. IN terminal.
Connect one end of the provided RF antenna cable to the video cassette player's
RF. OUT terminal and the other end to the TV's antenna terminal.
Connect the power cord to your household AC outlet.
Connection B
For connection of a TV that has VIDEO/AUDIO IN/OUT terminals. This connection is
necessary to record TV programmes. Use RCA type pin connection cords (available from
audio/video stores) for connection. This connection is in addition to connection A.
Follow steps 1 and 2 of "Connection A".
Connect the TV's VIDEO OUT and AUDIO OUT terminals to the video cassette
player's VIDEO IN and AUDIO IN terminals.
Connect the TV's VIDEO IN and AUDIO IN terminals to the VCP's VIDEO OUT and
AUDIO OUT terminals.
Connect the power cord to your household AC outlet.
1
2
3
1
2
3
4
8 Setting the video channel
To watch videos on your TV, it must be set to the same UHF channel as the video cassette
player. This channel is used as the video channel.
This video cassette player has been preset to UHF channel 36.
Note:
· When you have connected the VIDEO/AUDIO OUT terminals of this video cassette player
to your TV's video/audio in terminals (connection B of the "Connections" section), setting
the video channel is not necessary. In this case simply set the TV's TV/VCR switch to VCR.
IMPORTANT:
Before performing the following steps, make sure the player's power is off and there
is no cassette inserted in the player.
1
2
3
LP00000-000
­
+
+
­
TV/VCR
0000/X
PLAY
FF
REW
STOP
REC
VCP/TV
TV PR
TV
OK/OSD
MENU
PAUSE
TV
AUTO
­ TRACKING +
Front panel
1
1
1
1
1
Transmitting window
2
2
2
2
2
TV/VCR (Player) button
To switch JVC TV's mode between TV
and VIDEO.
3
3
3
3
3
TV button
To enable remote control of JVC TV.
4
4
4
4
4
AUTO button
To enable/disable auto tracking mode.
SP/LP/EP(
) button
· To select the recording tape speed.
· To select JVC TV's sounds.
5
5
5
5
5
(TV Muting) button
· To select output sound mode (HR-
P500K only).
· To mute the JVC TV volume.
6
6
6
6
6
3
3
3
3
3 PLAY button
To start playback.
7
7
7
7
7
REW
1
1
1
1
1
button
To rewind the video tape. Also to start
reverse shuttle search playback.
8
8
8
8
8
7
7
7
7
7 STOP button
To stop playback.
9
9
9
9
9
MENU button
To accesse Mode Set screen.
0
0
0
0
0
L/M buttons
To select the mode.
TV PR +/­ buttons
To select a prest position.
Access video channel set mode.
Hold down
§
§
§
§
§ on the video cassette
player until the both of POWER-ON
and STANDBY/REC indicators light.
Set video channels.
Set your TV to UHF channel 36.
· If the two vertical white bars appear
clearly on the screen as shown in the
illustration on the right, press OK
and then go to step 3.
· If the two vertical white bars do not
appear clearly, press TRACKING +
or ­ to set the video cassette player
to a vacant channel between 32 and
40 which is not occupied by any
local station in your area.
· The mode indicators tell chan-
nel position.
The indicators blink different
speed by the channel position
as shown on the right.
Press OK.
· STANDBY/REC indicator
goes off.
Set TV system.
Set "RF OUT" to "B/G" or "D/K".
(
See "
9 Mode set")
POWER-ON
STANDBY/REC
CH
POWER-ON
STANDBY/REC Blinking
(green)
(red)
Speed
40
­
blink
fast
39
­
blink
38
­
blink
37
­
blink
slow
36
light
light
­
35
blink
­
slow
34
blink
­
33
blink
­
32
blink
­
fast
TEST SIGNAL
The channel on
which the screen
to the left appear
clearly in step 2
is your Video
Channel.
To view picture signals from the video player, set
your TV to the Video Channel.
4
LPT0458-001A
6 On screen display
When "O.S.D" is set to "ON" (
See "
9 Mode set"), various operational indicators appear on
the TV screen.
q6
]
SP
NTSC 3.58
HIFI
­9 : 59 : 59
L
R
0
++
+
+
1
1
1
1
1
Operation mode indicators
2
2
2
2
2
Tape speed SP/LP/EP
3
3
3
3
3
Colour system indicator
4
4
4
4
4
Tape direction
5
5
5
5
5
Counter display
6
6
6
6
6
Audio mode display (HR-P500K only)
7
7
7
7
7
Tape position indicator
8
8
8
8
8
Cassette loaded mark
1
1
1
1
1
7
7
7
7
7
6
6
6
6
6
8
8
8
8
8
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
POWER ON
indicator
STANDBY/REC
indicator


background image
Problem
No power
Tape cannot be ejected
No picture
No colour
Shuttle search does not function
Disturbances in playback picture
Remote control does not function
Auto playback does not function
Recording does not function
The video cassette player does not
function properly
Check point
Is the power cord plugged in?
Is the power turned on?
Was the video cassette player's
§ button
pressed?
Is the TV set to the video channel?
Is a cassette loaded?
Are the connections correct?
Set the Colour System Output switch accord-
ing to the recorded tape system.
Is the video cassette player in the playback
mode?
Is tracking adjusted properly?
Is the TV adjusted properly?
Install this VCP a little way apart from the TV
set.
The batteries are weak.
Replace the batteries.
The video cassette's recording safety tab has
not been removed.
Are the connections correct?
Was the Record button pressed?
The video cassette's recording safety tab is
removed.
Microcomputer malfunction.
Disconnect the power plug from the AC outlet
and then re-insert it.
The microcomputer will be reset to its initial
mode.
1
2
Load a pre-recorded cassette.
If the safety tab on the cassette is re-
moved, playback will start automatically.
Press
3 to start playback.
·"B.E.S.T.PICTURESYSTEM"appears
on the screen. (when B.E.S.T. is set to
"ON".
"9 Mode set")
7 Press § or the remote control's 7
to stop playback. Then press
§ to
remove the cassette.
To fast forward or rewind the tape:
7 From the stop mode, press ¡ or
1.
12
10 Playback
NTSC, PAL and MESECAM video tapes
can be played back on this video cassette
player. Refer to the "Mode Set" section for
details.
Before proceeding:
· Turn on the power of the TV and video
cassette player.
· Make sure that the TV is set to the video
channel or that the TV's TV/VIDEO
switch is set to VIDEO (refer to the
"Setting the video channel" section for
details).
2
1
1
2
1
1
1
2
ATTENTION:
In the search, still, slow-motion or frame
advance mode,
· the picture will be distorted.
· the noise bars will appear.
· there will be loss of colour.
· the picture may not appear.
However, this is not malfunction.
These problems may occur especially
with HR-P100A.
Tracking adjustment
Automatic tracking is adjusted each time a
cassette is inserted in the video cassette
player, you may wish to adjust tracking
manually during playback.
Manual tracking:
Press the remote control's AUTO.
Press the remote control's TRACK-
ING + or ­ to adjust tracking.
7 Press AUTO to return to automatic
tracking.
11 Recording
Use the following procedure to record TV programmes on a blank video tape.
Before proceeding:
· To record TV programmes, the video cassette player must be connected to the TV as
shown in connection B of the "Connections" section.
· Turn on the power of the TV and video cassette player.
· Make sure that the video cassette's safety tab is intact. If it has been removed, cover the
hole with adhesive tape.
1 Load a blank video tape.
Press SP/LP/EP(
) to set the re-
cording speed.
Press
¶ to start recording. (On the
remote control unit press
¶ and 3
at the same time.)
The recording indicator will light dur-
ing recording.
B.E.S.T. takes place at the beginning of
each first SP and first LP (or EP) record-
ing after inserting the cassette.
7 Press § or the remote control's 7
to stop recording.
To stop recording temporarily:
7 Press 8.
The recording indicator will blink.
Press
3 to resume recording.
1
32
3
2
12 Karaoke features
Karaoke (HR-P500K only)
Use this feature to enjoy karaoke video.
Connect a microphone to both MIC 1 and
MIC 2 for duets.
Insert a pre-recorded Karaoke tape.
Press
3
3
3
3
3.
7 Karaoke search
You can search the desired tune by
pressing
2/3.
The Karaoke search can be operated
only when the mute section is more than
4 seconds between tune and tune.
Adjust the MIC or ECHO volume as
necessary.
Press MENU to access the Mode Set
screen then press
L/M to select MIC
or ECHO.
Press
2/3 to adjust the MIC or ECHO
volume.
Press MENU to return normal screen.
Start singing.
Note:
Check that the power is off (standby mode)
before plugging in the microphone.
1
2
3
4
13 B.E.S.T. picture system
ATTENTION:
Since the B.E.S.T. system works be-
fore recording actually starts, there is
a delay of approximately 7 seconds
after
¶ and 3 on the remote are
pressed, or
¶ on the player is pressed.
To make sure you record the desired
scene or programme in its entirely,
first perform the following steps:
1 Press and hold
8
8
8
8
8 and ¶
¶ to engage
the Record Pause mode.
· The player then automatically
check the condition of the tape
and, after approximately 7 sec-
onds, reenters Record Pause.
2 Press
3 to start recording.
· If you want to bypass the B.E.S.T.
system and begin recording im-
mediately, set "B.E.S.T." to "OFF".
The B.E.S.T. (Biconditional Equalized Sig-
nal Tracking) system checks the condition
of the tape in use during recording and
playback, and compensates to provide the
highest-possible recording and playback
pictures. The default setting for both
recording and playback is ``ON''.
Recording
The video cassette player assesses the
quality of the tape once you initiate record-
ing.
7 The player spends approximately 7 sec-
onds assessing the condition of the tape,
then begins recording.
Notes:
· The B.E.S.T. system works only after a
tape has been inserted and the Record
mode is first initiated. It does not work
during recording.
· Once the cassette is ejected, the
B.E.S.T. data is cancelled.
The next time the cassette is used for
recording, B.E.S.T. is re-performed.
Playback
The video cassette player assesses the
quality of the tape once you initiate playback.
When watching a tape recorded with
B.E.S.T. set to on, it is recommended that
you leave B.E.S.T. on during playback as
well.
7 The player adjusts the playback picture
quality based on the quality of the tape
in use.
7 B.E.S.T. is active during Auto Tracking.
Note:
When watching a rental tape, or one re-
corded on another video player, set B.E.S.T.
to on or off to your preference.
16 Specifications
Format ...................................... VHS Standard
Video recording system ........... Rotary, slant azimuth helical scan system
Rotary heads ............................ [HR-P500K]
4 video heads
[HR-P100A]
2 video heads
RF output ................................. System B/G, D/K type modulation
UHF ch 32 ­ 40 adjustable (preset ch 36)
Recording (line input) ............... PAL, SECAM (MESECAM tape)
NTSC 3.58, NTSC 4.43
Playback (line output) .............. PAL, SECAM (MESECAM tape)
NTSC 3.58
NTSC 4.43
Simulated PAL (NTSC tape)
Video
Line input level ....................... 0.5 ­ 2.0 Vp-p/75 ohms, unbalanced
Line output level .................... 1.0 Vp-p/75 ohms, unbalanced
S/N ratio ................................. More than 45 dB
Horizontal resolution .............. More than 250 lines
(PAL/MESECAM)
More than 220 lines (NTSC)
Audio
Line input level ....................... ­8 dBs/50 k ohms, unbalanced
Line output level .................... ­8 dBs/1 k ohm, unbalanced
Frequency response .............. 70 Hz to 10,000 Hz (Normal)
[HR-P500K]
20 Hz to 20,000 Hz (Hi-Fi audio)
Power requirements
Rating .................................... AC 110 V ­ 240 V, 50 Hz / 60 Hz
Operating ............................... AC 90 V ­ 260 V, 50 Hz / 60 Hz
Power consumption ................. [HR-P500K]
14 W
[HR-P100A]
13 W
Operation temperature ............. 5
°C to 40°C
Dimensions .............................. 360 mm (W)
× 94 mm (H) × 279 mm (D)
Weight ...................................... 3.2 kg
Standard accessories
Remote control unit .................. 1
Batteries for remote control ...... 2
RF antenna cable ..................... 1
Microphone (HR-P500K only) .. 1
Conversion plug ....................... 1
· Design and specifications subject to change without notice.
Still picture and frame advance
Use this feature to freeze the playback
picture and to advance one frame at a time.
The sound will be cut during this mode.
During playback:
Press
8
8
8
8
8.
The picture will be frozen.
Press
8
8
8
8
8 repeatedly to advance
frames.
Each time the button is pressed the
still picture will advance one frame.
7 Press 3 to resume normal playback.
Notes:
· If the picture shakes during the still
mode, use TRACKING +/­ to correct
the picture.
· After the picture has been frozen for
approx. 5 minutes, the still mode will
disengage to protect the video tape.
Slow motion playback
Slow motion playback is 1/6 of the normal
playback speed. The sound will be cut
during slow motion playback.
During playback:
Press
8
8
8
8
8 for 2 seconds.
7 Press 3 to return to the normal play-
back speed.
Notes:
· If the picture shakes during the slow
mode, use TRACKING +/­ to correct
the picture.
· After approx. 5 minutes, the slow mode
will disengage to protect the video tape.
Repeat playback
Use this feature to repeat playback of a
cassette 100 times.
During playback:
Press
3
3
3
3
3 for more than 5 seconds.
The Play indicator will blink slowly and
playback of the cassette will repeat
100 times automatically.
Press
7
7
7
7
7 to stop repeat playback.
Tape playback will be stopped and the
repeat playback mode will be can-
celled.
Note:
Pressing
3, 1
1
1
1
1, ¡
¡
¡
¡
¡ or 8
8
8
8
8 also stops Repeat
playback.
Shuttle search playback
Use this feature during playback to visually
locate any point on a recorded cassette.
The sound will be cut during shuttle search
operation.
During playback:
Press
¡
¡
¡
¡
¡ or 1
1
1
1
1 to engage shuttle
search forward or reverse.
7 Press 3 to resume normal playback.
Note:
For short searches, press and hold
¡
¡
¡
¡
¡ or
1
1
1
1
1. When released, normal playback will
continue.
Rewind playback or power off
When the tape has finished rewinding, the
Video cassette player will play back or turn
itself off.
During stop:
a- For Automatic Start Of Playback
Press
1
1
1
1
1, then press 3
3
3
3
3 within 2 sec-
onds.
b- For Automatic Power Off
Press
1
1
1
1
1, then press
within 2
seconds.
15 Troubleshooting
Editing To/From Another Recorder
14 Editing
About Head cleaning
7 If the picture playback becomes blurred, it does not mean that the recorded program has
been erased.
7 Dirt accumulated on the video heads after long periods of use causes such troubles. In
this case, head cleaning requiring highly technical care is necessary.
7 For head cleaning, consult the nearest JVC dealer.
Connect the player's AUDIO and
VIDEO OUT connectors to the
recorder's AUDIO and VIDEO IN
connectors.
Put the player in the Play mode.
Put the recorder in the Record mode.
Notes:
· NTSC tapes being played back in the
NTSC PLAYBACK ON PAL TV mode
cannot be dubbed to another recorder.
· When you dub an NTSC tape using your
recorder as the playback deck, select
NTSC 3.58 (or 4.43) with the Colour
System Output switch.
1
2
3
Important:
7 To edit, both the player and the
recorder must be of the same colour
system. Set "NTSC" to appropriate
mode. (
See "
9 Mode set")
9 Mode set
You can change various mode setting on the Mode Set screen by following procedure
described below.
Access the Mode Set screen.
Press MENU.
Select the mode.
Press
L/M to move the pointer to the item you want to change.
Select the mode setting.
Press
2/3.
Return to the normal screen.
Press MENU.
1
2
3
4
7MIC (HR-P500K only)
7ECHO (HR-P500K only)
7O.S.D.
ON
OFF
7B.E.S.T.
ON
OFF
7NTSC
NTSC3.58:
Select this mode to watch NTSC
tapes on a NTSC system TV.
NTSC4.43:
Select this mode to watch NTSC
tapes on a multi-system TV.
(that has an NTSC4.43 setting)
Select NTSC4.43 to record 4.43
signal.
NTSC
PAL:
Select this mode to watch NTSC
tapes on a PAL system TV.
7RFOUT
B/G: New Zealand, Kuwait,
U.A.E., Indonesia,
Singapore, Thailand,
Malaysia, Iran, Saudi Arabia
D/K: Egypt, Morocco, Lebanon,
Iraq, China, Mongolia, Russia
See "Karaoke features" below.
See "Karaoke features" below.
When the function is set to "ON", various operational
indicators appear on the TV screen.
NOTE:
When you use this video cassette player as the source
player for editing, be sure to set "O.S.D." to "OFF"
before starting.
You can set the B.E.S.T.(Bicondional Equalized Sig-
nal Tracking) system to "ON" or "OFF".
To watch an NTSC tape, it will be necessary to select
one of the output mode.
NOTES:
NTSC Playback on PAL TV
· The vertical size of the playback picture will shrink
and some picture "noise" may appear on the screen.
· The playback picture may roll. In this case adjust the
picture with the TV's vertical hold knob (with some
TV's this adjustment may not be possible).
· The colour of the playback picture may differ from
the original.
· In the forward/reverse shuttle search or still modes
there may be no colour depending on the TV and
video cassette player combination.
Set appropriate TV system that matches the system of
TV being used.
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
­
+
+
­
TV/VCR
0000/X
PLAY
FF
REW
STOP
REC
TV PR
TV
OK/OSD
MENU
PAUSE
TV
AUTO
­ TRACKING +
2
3
3
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
SUPER
HEAD CLEANER
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
LP00000-000
­
+
+
­
TV/VCR
0000/X
PLAY
FF
REW
STOP
REC
VCP/TV
TV PR
TV
OK/OSD
MENU
PAUSE
TV
AUTO
­ TRACKING +
The default setting is bold in the table below.
RF OUT
ANT.IN
OUT
IN
AUDIO
R
L
VIDEO
RF OUT
ANT.IN
OUT
IN
AUDIO
R
L
VIDEO
TV
Receiver
Player
Recorder
Audio/Video signals
VIDEO
CHANNEL
MIC MIN +---+-7-+ MAX
ECHO
0 +---+-7-+ 10
O.S.D.
ON
B.E.S.T.
ON
NTSC
NTSC 3.58
RF OUT
B/G
[
L/M]
= [2/3]
[MENU] : EXIT
COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN LTD.
Printed in Malaysia
0800IYV
*ID*PJ
7 Soundtrack Selection (HR-P500K
only)
During Playback
Pressing
changes the soundtrack
being played back as follows:
Counter reset
Press OSD to show counter display
on the screen.
Press 0000 to reset the counter.
2
1
Notes:
· To engage recording standby, press ¶ and then press 8. The STANDBY/REC indicator
will blink during recording standby. Press
3 again to start recording.
· If ¶ does not work, check to see if the cassette safety tab has been removed.
· The player automatically stops when record-standby continues for more than 5 minutes.
· The video tape will be rewound automatically when the end of the tape is reached.
"MIC" and "ECHO"appears
only with the HR-P500K.
HI-FI
HI-FI L
HI-FI R
HI-FI
NORM
NORM


background image
OUT
IN
RF OUT
ANT.IN
AUDIO
R
L
VIDEO
VIDEO CASSETTE PLAYER
HR-P94K/P54A
Thank you for purchasing this JVC video cassette player. To ensure optimum performance
of this unit, please read this instruction manual thoroughly.
INSTRUCTIONS
English
PAL NTSC
7 Only cassettes marked "VHS" can be used with this video cassette player.
2 Automatic features
Auto power on
The video cassette player is automatically
turned on when the tape is inserted.
Auto rewind
The video tape is automatically rewound
when the end of the tape is reached during
the play, recording or shuttle search forward
mode.
Auto playback
If the video cassette's safety tab has been
removed, playback will begin automatically
when the tape is inserted into the video
cassette player.
Power off eject
Even when the video cassette player's
power is off, pressing the eject button will
turn the power on and eject the tape. Once
ejected, the power will be turned off again
automatically.
Auto head cleaning
When a tape is loaded or ejected the VCP
video head is cleaned automatically.
1 Features
· 3 system (PAL/MESECAM/NTSC)
· NTSC playback (on PAL television)
· RF output G/K switchable
· Digital auto tracking
· HQ (High Quality)
· Auto playback function
· Repeat playback
· Shuttle search
· Still and slow motion
· Line recording
· Karaoke (HR-P94K only)
· B.E.S.T.(BiconditionalEqualizedSignal
Tracking) picture system
3 Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE IN-SIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
The STANDBY/ON
button does not completely shut off mains power from the unit,
but switches operating current on and off.
This unit is produced to comply with Standard IEC 60065.
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space
on all sides to allow for ventilation (10 cm or more on both side, on top and at the rear.)
When discarding batteries, environmental problems must be considered and the local rules
or laws governing the disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the player, remote
control or video cassette player.
1. DO NOT place the player . . .
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the player's ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may
not be able to get out.)
3. DO NOT place heavy objects on the player or remote control.
4. DO NOT place anything which might spill on top of the player or remote control.
If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place
any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus.
8. AVOID violent shocks to the player during transport.
Beware of moisture condensation
Moisture in the air will condense on the VCP when you move it from a cold place to a warm
place, or under extremely humid conditions -- just as water droplets form on the surface of
a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to
the tape. In conditions where condensation may occur, keep the VCP's power turned on for
a few hours to let the moisture dry.
When transporting
7 Be sure to remove cassette from VCP before packing.
7 Avoid violent shocks to the VCP during packing and transport.
4 Controls
Front panel
1
1
1
1
1
STANDBY/ON
button
To turn the power on and off (standby mode).
2
2
2
2
2
Cassette loading slot
Load the video cassette here.
3
3
3
3
3
Rewind
1
1
1
1
1 button
To rewind the video tape and to start reverse shuttle search playback mode.
4
4
4
4
4
Play
#
#
#
#
# button
To start playback.
5
5
5
5
5
Fast forward
¡
¡
¡
¡
¡ button
To fast forward the video tape and to start forward shuttle search playback mode.
6
6
6
6
6
SP / LP / EP button
To select the recording tape speed.
7
7
7
7
7
Stop/Eject
§
§
§
§
§ button
To stop playback and to eject the video tape.
8
8
8
8
8
Record
¶ button
To start recording.
9
9
9
9
9
OSD button
To display the information on the television's display.
0
0
0
0
0
Remote sensor window
For remote control operation.
!
!
!
!
!
STANDBY / REC indicator
·
Lights when the power turns off (Standby mode) or during recording mode.
·
Blinks during recording pause mode.
@
@
@
@
@
POWER-ON indicator
Lights when the power turns on.
#
#
#
#
#
MIC input terminals (HR-P94K only)
Rear panel
1
1
1
1
1
AC power cord
2
2
2
2
2
RF. OUT terminal
3
3
3
3
3
AUDIO/VIDEO IN terminals
4
4
4
4
4
AUDIO/VIDEO OUT terminals
5
5
5
5
5
ANT. IN terminal
The video cassette player illustrations appearing in this instruction manual are of the HR-P94K.
HR-P94K
HR-P54A
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
SUPER
HEAD CLEANER
Hi-Fi Karaoke
STANDBY/ON
MIC
2
1
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
VIDEO CASSETTE PLAYER
HR-P94K
PAL NTSC
Hi-Fi KARAOKE MULTI 6HEAD
LONGPLAY RECORDING AUTO VOLTAGE B.E.S.T. PICTURE
PAL/MESECAM/NTSC3.58/4.43
NTSC PLAYBACK ON PAL TV
MULTI SYSTEM
SUPER
HEAD CLEANER
STANDBY/ON
POWER-ON
STANDBY/REC
OSD
SP/LP/EP
VIDEO CASSETTE PLAYER
HR-P54A
OUT
IN
RF OUT
ANT.IN
AUDIO
R
L
VIDEO
OUT
IN
RF OUT
ANT.IN
AUDIO
L
VIDEO
Rear panel
HR-P94K
HR-P54A
5 Wireless remote control
When using the remote control for operation of the video cassette player, make sure that it
is pointed at the remote sensor window.
You can also use the player's remote control to operate a JVC television.
!
!
!
!
!
STANDBY/ON
button
To turn the power on and off (standby
@
@
@
@
@
TRACKING ­/+ buttons
To adjust tracking during playback.
#
#
#
#
#
0000 /
button
To reset the tape counter.
$
$
$
$
$
FF
¡
¡
¡
¡
¡ Z
Z
Z
Z
Z button
To fast forward the video tape. Also to
start forward shuttle search playback.
%
%
%
%
%
8
8
8
8
8 PAUSE button
To freeze the picture during playback.
Also to engage the recording pause
mode.
^
^
^
^
^
2/3 buttons
To set the mode.
TV
+/­ (TV Volume) buttons
To adjust the TV volume.
&
&
&
&
&
OK/OSD button
· To fix the setting.
· To display the information on the
television's display.
*
*
*
*
*
¶ REC button
Press the
¶ REC and 3
3
3
3
3 PLAY but-
tons together, to start recording.
Operating JVC TVs
Buttons with a small dot on the left side of
the name can also be used to operate your
JVC TV while holding down TV.
To operate your TV, while holding down TV,
press the corresponding button:
, TV/
VCR, TV PR +/­, TV
+/­ (TV Volume),
(TV Muting),
(TV Sounds).
Notes:
· Point the remote control toward the
remote sensor window.
· The maximum operating distance of
the remote control is about 8 m.
· When inserting the batteries, be sure to
insert in the correct directions as indi-
cated under the battery cover.
· If the remote control doesn't work properly,
remove its batteries, wait a short time,
replace the batteries and then try again.
7 Connections
Make sure that the power to the video cassette player and TV is off before making the
following connections.
Connection B
Connection A
Note:
If you put a TV set directly on this Video cassette player or install it too close to a TV set,
noise may occur. If this noise occurs, separate the Video cassette player and the TV set.
Connection A (basic)
In order to use the video cassette player it must be connected between the antenna and the
TV.
Connect your TV antenna cable to the video cassette player's ANT. IN terminal.
Connect one end of the provided RF antenna cable to the video cassette player's
RF. OUT terminal and the other end to the TV's antenna terminal.
Connect the power cord to your household AC outlet.
Connection B
For connection of a TV that has VIDEO/AUDIO IN/OUT terminals. This connection is
necessary to record TV programmes. Use RCA type pin connection cords (available from
audio/video stores) for connection. This connection is in addition to connection A.
Follow steps 1 and 2 of "Connection A".
Connect the TV's VIDEO OUT and AUDIO OUT terminals to the video cassette
player's VIDEO IN and AUDIO IN terminals.
Connect the TV's VIDEO IN and AUDIO IN terminals to the VCP's VIDEO OUT and
AUDIO OUT terminals.
Connect the power cord to your household AC outlet.
1
2
3
1
2
3
4
8 Setting the video channel
To watch videos on your TV, it must be set to the same UHF channel as the video cassette
player. This channel is used as the video channel.
This video cassette player has been preset to UHF channel 36.
Note:
· When you have connected the VIDEO/AUDIO OUT terminals of this video cassette player
to your TV's video/audio in terminals (connection B of the "Connections" section), setting
the video channel is not necessary. In this case simply set the TV's TV/VCR switch to VCR.
IMPORTANT:
Before performing the following steps, make sure the player's power is off and there
is no cassette inserted in the player.
1
2
3
LP00000-000
­+
+
­
TV/VCR
0000/X
PLAY
FF
REW
STOP
REC
VCP/TV
TV PR
TV
OK/OSD
MENU
PAUSE
TV
AUTO
­ TRACKING +
Front panel
1
1
1
1
1
Transmitting window
2
2
2
2
2
TV/VCR (Player) button
To switch JVC TV's mode between TV
and VIDEO.
3
3
3
3
3
TV button
To enable remote control of JVC TV.
4
4
4
4
4
AUTO button
To enable/disable auto tracking mode.
SP/LP/EP(
) button
· To select the recording tape speed.
· To select JVC TV's sounds.
5
5
5
5
5
(TV Muting) button
· To select output sound mode (HR-
P94K only).
· To mute the JVC TV volume.
6
6
6
6
6
3
3
3
3
3 PLAY button
To start playback.
7
7
7
7
7
REW
1
1
1
1
1 +
+
+
+
+ button
To rewind the video tape. Also to start
reverse shuttle search playback.
8
8
8
8
8
7
7
7
7
7 STOP button
To stop playback.
9
9
9
9
9
MENU button
To accesse Mode Set screen.
0
0
0
0
0
v/w buttons
To select the mode.
TV PR +/­ buttons
To select a prest position.
Access video channel set mode.
Hold down
§
§
§
§
§ on the video cassette
player until the both of POWER-ON
and STANDBY/REC indicators light.
Set video channels.
Set your TV to UHF channel 36.
· If the two vertical white bars appear
clearly on the screen as shown in the
illustration on the right, press OK
and then go to step 3.
· If the two vertical white bars do not
appear clearly, press TRACKING +
or ­ to set the video cassette player
to a vacant channel between 32 and
40 which is not occupied by any
local station in your area.
· The mode indicators tell chan-
nel position.
The indicators blink different
speed by the channel position
as shown on the right.
Press OK.
· STANDBY/REC indicator
goes off.
Set TV system.
Set "RF OUT" to "B/G" or "D/K".
(
See "
9 Mode set")
NTSC PLAYBACK ON PAL TV
POWER-ON
STANDBY/REC
CH
POWER-ON
STANDBY/REC Blinking
(green)
(red)
Speed
40
­
blink
fast
39
­
blink
38
­
blink
37
­
blink
slow
36
light
light
­
35
blink
­
slow
34
blink
­
33
blink
­
32
blink
­
fast
TEST SIGNAL
The channel on
which the screen
to the left appear
clearly in step 2
is your Video
Channel.
To view picture signals from the video player, set
your TV to the Video Channel.
4
LPT0457-001A
6 On screen display
When "O.S.D" is set to "ON" (
See "
9 Mode set"), various operational indicators appear on
the TV screen.
q6
]
SP
NTSC 3.58
HIFI
­9 : 59 : 59
L
R
0
++
+
+
1
1
1
1
1
Operation mode indicators
2
2
2
2
2
Tape speed SP/LP/EP
3
3
3
3
3
Colour system indicator
4
4
4
4
4
Tape direction
5
5
5
5
5
Counter display
6
6
6
6
6
Audio mode display (HR-P94K only)
7
7
7
7
7
Tape position indicator
8
8
8
8
8
Cassette loaded mark
1
1
1
1
1
7
7
7
7
7
6
6
6
6
6
8
8
8
8
8
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
POWER ON
indicator
STANDBY/REC
indicator


background image
Problem
No power
Tape cannot be ejected
No picture
No colour
Shuttle search does not function
Disturbances in playback picture
Remote control does not function
Auto playback does not function
Recording does not function
The video cassette player does not
function properly
Check point
Is the power cord plugged in?
Is the power turned on?
Was the video cassette player's
§ button
pressed?
Is the TV set to the video channel?
Is a cassette loaded?
Are the connections correct?
Set the Colour System Output switch accord-
ing to the recorded tape system.
Is the video cassette player in the playback
mode?
Is tracking adjusted properly?
Is the TV adjusted properly?
Install this VCP a little way apart from the TV
set.
The batteries are weak.
Replace the batteries.
The video cassette's recording safety tab has
not been removed.
Are the connections correct?
Was the Record button pressed?
The video cassette's recording safety tab is
removed.
Microcomputer malfunction.
Disconnect the power plug from the AC outlet
and then re-insert it.
The microcomputer will be reset to its initial
mode.
1
2
Load a pre-recorded cassette.
If the safety tab on the cassette is re-
moved, playback will start automatically.
Press -
-
-
-
- to start playback.
·"B.E.S.T.PICTURESYSTEM"appears
on the screen. (when B.E.S.T. is set to
"ON".
"9 Mode set")
7 Press § or the remote control's 7
to stop playback. Then press
§ to
remove the cassette.
To fast forward or rewind the tape:
7 From the stop mode, press ¡ or
1.
12
10 Playback
NTSC, PAL and MESECAM video tapes
can be played back on this video cassette
player. Refer to the "Mode Set" section for
details.
Before proceeding:
· Turn on the power of the TV and video
cassette player.
· Make sure that the TV is set to the video
channel or that the TV's TV/VIDEO
switch is set to VIDEO (refer to the
"Setting the video channel" section for
details).
2
1
1
2
1
1
1
2
ATTENTION:
In the search, still, slow-motion or frame
advance mode,
· the picture will be distorted.
· the noise bars will appear.
· there will be loss of colour.
· the picture may not appear.
However, this is not malfunction.
These problems may occur especially
with HR-P54A.
Tracking adjustment
Automatic tracking is adjusted each time a
cassette is inserted in the video cassette
player, you may wish to adjust tracking
manually during playback.
Manual tracking:
Press the remote control's AUTO.
Press the remote control's TRACK-
ING + or ­ to adjust tracking.
7 PressAUTOtoreturntoautomatic
tracking.
11 Recording
Use the following procedure to record TV programmes on a blank video tape.
Before proceeding:
· To record TV programmes, the video cassette player must be connected to the TV as
shown in connection B of the "Connections" section.
· Turn on the power of the TV and video cassette player.
· Make sure that the video cassette's safety tab is intact. If it has been removed, cover the
hole with adhesive tape.
1 Load a blank video tape.
Press SP/LP/EP(
) to set the re-
cording speed.
Press
¶ to start recording. (On the
remote control unit press
¶ and 3
at the same time.)
The recording indicator will light dur-
ing recording.
B.E.S.T. takes place at the beginning of
each first SP and first LP (or EP) record-
ing after inserting the cassette.
7 Press §ortheremotecontrol's
7
tostoprecording.
To stop recording temporarily:
7 Press 8.
The recording indicator will blink.
Press
3 to resume recording.
1
32
3
2
12 Karaoke features
Karaoke (HR-P94K only)
Use this feature to enjoy karaoke video.
Connect a microphone to both MIC 1 and
MIC 2 for duets.
Insert a pre-recorded Karaoke tape.
Press
3
3
3
3
3.
7 Karaokesearch
You can search the desired tune by
pressing
2/3.
The Karaoke search can be operated
only when the mute section is more than
4 seconds between tune and tune.
Adjust the MIC or ECHO volume as
necessary.
Press MENU to access the Mode Set
screen then press v/w to select MIC
or ECHO.
Press
2/3 to adjust the MIC or ECHO
volume.
Press MENU to return normal screen.
Start singing.
Note:
Check that the power is off (standby mode)
before plugging in the microphone.
1
2
3
4
13 B.E.S.T. picture system
ATTENTION:
Since the B.E.S.T. system works be-
fore recording actually starts, there is
a delay of approximately 7 seconds
after
¶ and 3 on the remote are
pressed, or
¶ on the player is pressed.
To make sure you record the desired
scene or programme in its entirely,
first perform the following steps:
1 Press and hold
8
8
8
8
8 and ¶
¶ to engage
the Record Pause mode.
· The player then automatically
check the condition of the tape
and, after approximately 7 sec-
onds, reenters Record Pause.
2 Press
3 to start recording.
· If you want to bypass the B.E.S.T.
system and begin recording im-
mediately, set "B.E.S.T." to "OFF".
The B.E.S.T. (Biconditional Equalized Sig-
nal Tracking) system checks the condition
of the tape in use during recording and
playback, and compensates to provide the
highest-possible recording and playback
pictures. The default setting for both
recording and playback is ``ON''.
Recording
The video cassette player assesses the
quality of the tape once you initiate record-
ing.
7 The player spends approximately 7 sec-
onds assessing the condition of the tape,
then begins recording.
Notes:
· The B.E.S.T. system works only after a
tape has been inserted and the Record
mode is first initiated. It does not work
during recording.
· Once the cassette is ejected, the
B.E.S.T. data is cancelled.
The next time the cassette is used for
recording, B.E.S.T. is re-performed.
Playback
The video cassette player assesses the
quality of the tape once you initiate playback.
When watching a tape recorded with
B.E.S.T. set to on, it is recommended that
you leave B.E.S.T. on during playback as
well.
7 The player adjusts the playback picture
quality based on the quality of the tape
in use.
7 B.E.S.T. is active during Auto Tracking.
Note:
When watching a rental tape, or one re-
corded on another video player, set B.E.S.T.
to on or off to your preference.
16 Specifications
Format ...................................... VHS Standard
Video recording system ........... Rotary, slant azimuth helical scan system
Rotary heads ............................ [HR-P94K]
4 video heads
[HR-P54A]
2 video heads
RF output ................................. System B/G, D/K type modulation
UHF ch 32 ­ 40 adjustable (preset ch 36)
Recording (line input) ............... PAL, SECAM (MESECAM tape)
NTSC 3.58, NTSC 4.43
Playback (line output) .............. PAL, SECAM (MESECAM tape)
NTSC 3.58
NTSC 4.43
Simulated PAL (NTSC tape)
Video
Line input level ....................... 0.5 ­ 2.0 Vp-p/75 ohms, unbalanced
Line output level .................... 1.0 Vp-p/75 ohms, unbalanced
S/N ratio ................................. More than 45 dB
Horizontal resolution .............. More than 250 lines
(PAL/MESECAM)
More than 220 lines (NTSC)
Audio
Line input level ....................... ­8 dBs/50 k ohms, unbalanced
Line output level .................... ­8 dBs/1 k ohm, unbalanced
Frequency response .............. 70 Hz to 10,000 Hz (Normal)
[HR-P94K]
20 Hz to 20,000 Hz (Hi-Fi audio)
Power requirements
Rating .................................... AC 110 V ­ 240 V, 50 Hz / 60 Hz
Operating ............................... AC 90 V ­ 260 V, 50 Hz / 60 Hz
Power consumption ................. [HR-P94K]
14 W
[HR-P54A]
13 W
Operation temperature ............. 5
°C to 40°C
Dimensions .............................. 360 mm (W)
× 94 mm (H) × 279 mm (D)
Weight ...................................... 3.2 kg
Standard accessories
Remote control unit .................. 1
Batteries for remote control ...... 2
RF antenna cable ..................... 1
Microphone (HR-P94K only) .... 1
· Design and specifications subject to change without notice.
Still picture and frame advance
Use this feature to freeze the playback
picture and to advance one frame at a time.
The sound will be cut during this mode.
During playback:
Press
8
8
8
8
8.
The picture will be frozen.
Press
8
8
8
8
8 repeatedly to advance
frames.
Each time the button is pressed the
still picture will advance one frame.
7 Press 3toresumenormalplayback.
Notes:
· If the picture shakes during the still
mode, use TRACKING +/­ to correct
the picture.
· After the picture has been frozen for
approx. 5 minutes, the still mode will
disengage to protect the video tape.
Slow motion playback
Slow motion playback is 1/6 of the normal
playback speed. The sound will be cut
during slow motion playback.
During playback:
Press
8
8
8
8
8 for 2 seconds.
7 Press 3toreturntothenormalplay-
backspeed.
Notes:
· If the picture shakes during the slow
mode, use TRACKING +/­ to correct
the picture.
· After approx. 5 minutes, the slow mode
will disengage to protect the video tape.
Repeat playback
Use this feature to repeat playback of a
cassette 100 times.
During playback:
Press
3
3
3
3
3 for more than 5 seconds.
The Play indicator will blink slowly and
playback of the cassette will repeat
100 times automatically.
Press
7
7
7
7
7 to stop repeat playback.
Tape playback will be stopped and the
repeat playback mode will be can-
celled.
Note:
Pressing
3, 1
1
1
1
1, ¡
¡
¡
¡
¡ or 8
8
8
8
8 also stops Repeat
playback.
Shuttle search playback
Use this feature during playback to visually
locate any point on a recorded cassette.
The sound will be cut during shuttle search
operation.
During playback:
Press
¡
¡
¡
¡
¡ or 1
1
1
1
1 to engage shuttle
search forward or reverse.
7 Press 3toresumenormalplayback.
Note:
For short searches, press and hold
¡
¡
¡
¡
¡ or
1
1
1
1
1. When released, normal playback will
continue.
Rewind playback or power off
When the tape has finished rewinding, the
Video cassette player will play back or turn
itself off.
During stop:
a- For Automatic Start Of Playback
Press
1
1
1
1
1, then press 3
3
3
3
3 within 2 sec-
onds.
b- For Automatic Power Off
Press
1
1