CRATE GFX-212 - Owner's Manual Immediate Download

OWNER'S MANUAL

P/N 47-476-03 · 08/98

GFX-120/212 Amplifier

Congratulations!

You are now the proud owner of the Crate GFX-120/212 guitar amplifier. These

rugged amplifiers combine outstanding features with serious clean and distorted

sounds. An easy to operate DSP section lets you dial in a variety of digital effects such

as delay, flange, chorus and reverb with separate level control. Channel selection,

Crate's exclusive Shape circuit, and DSP on/off are controllable by the supplied three-

button footswitch. An insert jack allows virtually noise-free connection of your favorite

effects.

Like all Crate products, your GFX-120/212 is Musician Made in the U.S.A., using

only the best components. Extensive testing at the hands (and ears) of skilled techni-

cians and musicians insures you that this amplifier is the absolute best it can be.

In order to get the most out of your new amplifier, we strongly urge you to go over

the information contained in this manual before you begin playing.

And thank you for choosing

Crate continually develops new products, as well as improves existing ones. For this reason, the

specifications and information in this Crate manual are subject to change without notice.

Output Power Rating

115 watts RMS @ 5% THD 4 ohms load 120VAC

Speaker Size and Rating

GFX-120: (1) Custom Design 12", 4 ohms

GFX-212: (2) Crate Custom 12", 8 ohms

Input Impedance

470k ohms

Maximum Input Signal Level Accepted

7 volts, peak-to-peak

Total System Gain

Overdrive Channel: 110dB all controls @10, Gain 2; 88dB Gain 1

Clean Channel: 58dB all controls @10

Overdrive Channel:

Low Control:

11dB Range @ 80Hz

Shape Control:

Proprietary Circuit

High Control:

10dB Range @ 10kHz

Clean Channel:

Low Control:

22dB Range @ 80Hz

Mid Control:

14dB Range @ 600Hz

High Control:

28dB Range @ 10kHz

Input Power Requirements

120 VAC, 60Hz, 95VA

100/115VAC, 50/60Hz, 95VA

230VAC, 50/60Hz, 95VA

Cabinet Size and Weight:

GFX-120: 17-1/2" H x 19-1/4" W x 9-3/4" D, 44 lbs.

GFX-212: 21" H x 26-1/2" W x 11" D, 50 lbs.

The GFX-120/212 is covered with a durable Tolex material: wipe it

clean with a lint-free cloth. Never spray cleaning agents onto the

cabinet. Avoid abrasive cleansers which could damage the finish.

GFX-120/212 TECHNICAL SPECIFICATIONS

THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED TO PROVIDE SAFE AND RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE

UNIT AND PREVENT ACCIDENTAL DAMAGES OR INJURY, PLEASE FOLLOW THESE PRECAUTIONARY GUIDELINES:

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN CHASSIS; DO NOT DEFEAT OR REMOVE THE GROUND PIN OF THE POWER

CORD; CONNECT ONLY TO A PROPERLY GROUNDED AC POWER OUTLET.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION: OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE

LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS

OPERATED AT HIGH VOLUME.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"

"ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES."

"REFERREZ-VOUS AU MANUAL D'UTILISATION"

"UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN"

EXPLANATION OF GRAPHICAL SYMBOLS:

EXPLICACION DE SIMBOLOS GRAFICOS:

EXPLICATION DES SYMBÔLES GRAPHIQUES:

"DANGEROUS VOLTAGE"

"VOLTAJE PELIGROSO"

"DANGER HAUTE TENSION"

"GEFAHLICHE SPANNUNG"

ATTENTION

RISQUE D'ELECTROCUTION

NE PAS OUVRIR

ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS

ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE

PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN

TECHNICIEN QUALIFIE.

VORSICHT

ELEKTRISCHE SCHLAGGEFAHR

NICHT OFFENEN

VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT

DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM

BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM

WARTUNGSPERSONAL ZU UBERLASSEN.

GFX-120/212

GUITAR AMPLIFIER WITH

DIGITAL SIGNAL PROCESSING

1: INPUT: Connect your guitar here using a shield-

ed instrument cable.

OVERDRIVE CHANNEL: A high gain channel giv-

ing you sounds from a slight edge to serious over-

drive.

2: GAIN 1: When active, sets the amount of com-

pression and distortion from the amplifier. At far

left, the sound will have a thick compressed quali-

ty. As you turn the control to the right the amount of

distortion increases. Gain 1 produces less intense

distortion than Gain 2 and is active only when the

Gain Select switch (#5) is out.

3: GAIN 2: When active, sets the amount of com-

pression and distortion from the amplifier. At far

left, the sound will have a thick compressed quali-

ty. As you turn the control to the right the amount of

distortion increases. Gain 2 produces more intense

distortion than Gain 1 and is active only when the

Gain Select switch (#5) is in.

4: SHAPE: Working in conjunction with the Gain 2

control, rotate the Shape control until you find the

sound you're looking for. Turning the control

towards the left enhances the mid frequencies;

turning it to the right enhances the low and high fre-

quencies. (Only affects Gain 2 when active.)

5: GAIN SELECT: Switches between Gain 1 (out)

and Gain 2 (in). A footswitch (#22) overrides this

switch.

6: LOW: Adjusts the low frequency output level: to

the left reduces the low frequency output; to the

right increases it. This control allows a range of

11dB at 80Hz.

7: HIGH: Adjusts the high frequency output level:

to the left reduces the high frequency output, to the

right increases it. This control allows a range of

10dB at 10kHz.

8: LEVEL: Sets the output volume level from the

Overdrive Channel: in the far-left position there is

no output; turning the control to the right increases

the output. Use this control along with the Gain and

Shape controls (#2, 3 & 4) to create a wide variety

of sounds.

9: CHANNEL SELECT: When this switch is

pressed in the Overdrive Channel is engaged. The

Clean Channel is selected when this switch is out.

A footswitch (#22) overrides this switch. The adja-

cent LEDs indicate which channel is selected.

CLEAN CHANNEL:

A normal

gain

channel

designed to give you crystal clear sounds.

10: LEVEL: Sets the output volume level from the

Clean Channel: in the far-left position there is no

output; turning the control to the right increases the

output level.

11: LOW: Adjusts the low frequency output level:

to the left reduces the low frequency output; to the

right increases it. This control allows a range of

22dB at 80Hz.

12: MID: Adjusts the mid frequency output level: to

the left reduces the midrange output; turning it to

the right increases it. This control allows a range of

14dB at 600Hz.

13: HIGH: Adjusts the high frequency output level:

to the left reduces the high frequency output; to the

right increases it. This control allows a range of

28dB at 10kHz.

14: DSP LEVEL: Adjust the amount of digital sig-

nal processing with this control: in the full-left posi-

tion the output signal is "dry" (no effect); rotating

the control to the right increases the amount of

effect. The DSP can be turned on and off with a

footswitch (#23).

15: DSP MODE: Select the type of digital effect(s)

desired with this control. Each category and its

central location is called out (delay, flange, etc.) by

the markings around the control; there are two vari-

ations per effect, as follows:

GFX-120/212 Amplifier

· Slapback delay

· Long delay w/regeneration

· Light Flange

· Heavy Flange

· Slow Chorus

· Fast Chorus

· Chorus w/small room reverb

· Chorus w/large room reverb

· Small room reverb

· Large room reverb

16: INSERT: Connect an external effects device

via this jack. Use a stereo 1/4" male Y-cord: ring =

send, tip = return, sleeve = ground. See the illus-

tration on the panel to the right for more informa-

tion.

17: EXT. SPEAKER: Connect to an extension

speaker cabinet with this jack. The jack is wired in

series with the internal speaker(s).

18: POWER ON LED: Lights when the amplifier is

turned on.

19: POWER SWITCH: Turns the amplifier ON in

the up position, off in the down position.

20. POWER CORD (rear panel, not shown): Your

GFX-120/212 is equipped with a heavy-duty

grounded three-wire power cord. Be sure this cord

is properly plugged into a safely wired grounded

120 volt, 60Hz AC power outlet before use. (If your

GFX-120/212 was purchased outside the United

States, refer to the rear panel for power ratings.)

For your safety, never attempt to defeat the ground

connection on this cord.

21: FUSE (rear panel, not shown): Protects the

amplifier against damages caused from a faulty AC

power source or other problems. If the fuse blows,

replace it ONLY with the same size and type fuse.

If the fuse blows repeatedly check the AC source;

if it's okay, contact your Crate dealer for service

information.

22: CHANNEL SELECT / GAIN FOOTSWITCH

JACK (rear panel, not shown): Connect the

stereo 1/4" plug of the supplied three-button

footswitch here for remote control of the Channel

Select and Gain Select settings.

23: DSP FOOTSWITCH JACK (rear panel, not

shown): Connect the mono 1/4" plug of the sup-

plied three-button footswitch here for remote con-

trol of the DSP on and off.

Connecting to the Insert jack:

The Insert jack (#16) lets you patch external effects

into the amplifier just prior to its power amp stage.

Use Crate's CYC6MS stereo-to-mono Y-cord or an

adapter such as Crate's CA11Y and 2 1/4" mono

signal cables to connect to the effect as shown

below.

TIP

RING

SLEEVE

RETURN

SEND

GROUND

Stereo-to-mono Y-cord:

to Insert jack

(CYC6MS)

(CA11Y)

"Send"

plug:

effect

"IN"

"Return"

plug:

from

effect

"OUT"

External Effect

TIP

RING

SLEEVE

Y-adapter and 2 cables:

to Insert jack

effect

"IN"

from

effect

"OUT"

Tip =

"Return"

Ring =

"Send"

External Effect