background image
USER'S GUIDE 2482/2600
1
· After you perform an operation in any mode, pressing B returns to the Timekeeping
Mode.
· In any mode, press A to illuminate the display.
General Guide
· Press B to change from mode to mode.
Timekeeping Mode
[Modules 2482, 2600]
Alarm Mode
Stopwatch Mode
Time Setting Mode
Press
.
Timekeeping Mode
· In the Timekeeping Mode, press C to switch
between the 12-hour and 24-hour formats.
· With the 12-hour format, the P (PM) indicator appears to
the left of the hour digits for times in the range of noon
to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to
11:59 a.m.
· With the 24-hour format, times are displayed in the
range of 0:00 to 23:59, with 24 indicator.
· Day of the week is displayed as follows.
SU: Sunday
MO: Monday
TU: Tuesday
WE: Wednesday
TH: Thursday
F R : Friday
SA: Saturday
Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark.
· The electro-luminescent panel that provides illumination loses power after very long
use.
· The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
· The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
· Frequent use of the backlight shortens the battery life.
Alarm Mode
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
To set the alarm time
1. Hold down A while in the Alarm Mode until the hour
digits start to flash on the display. The hour digits flash
because they are
selected.
· This operation automatically turns on the alarm.
Stopwatch Mode
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is
59 minutes, 59.99 seconds.
PM indicator
Day of the week
Day
Hour
Seconds
Minutes
Hourly time
signal on
indicator
Mode indicator
Hour
Alarm on
indicator
Minutes
2. Press A to change the selection in the following sequence.
· Pressing A also illuminates the display.
Hour
Minutes
Normal Alarm Mode (No digit flashes)
3. Press C to increase the selected digits. Holding down C changes the number at
high speed.
· The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press A to return to the Alarm Mode.
To stop the alarm
Press A to stop the alarm after it starts to sound.
To switch the Daily Alarm and Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[Alarm on Indicator/Hourly Time Signal on Indicator]
Hourly Time
Signal only
Daily Alarm
only
Both off
Both on
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
Mode indicator
Split time
indicator
Minutes
Seconds
1/100 second
(a) Elapsed time measurement
Start
Stop
Re-start
Stop
Clear
Start
Split
(SPL displayed)
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
(b) Split time measurement
(c) Split time and 1st-2nd place times
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
· Pressing A also illuminates the display.
Time Setting Mode
To set the time and date
1. Use B to enter the Time Setting Mode.
· The second's digits flash because they are selected.
2. Press A to change the selection in the following
sequence.
· Pressing A also illuminates the display.
Seconds
Hour
Minutes
Day of week
Day
Month
Day of the week
Day
Hour
Minutes
Seconds
PM indicator
3. While the second's digits are selected (flashing), press C to reset the seconds to
"00". If you press C while the second's count is in the range of 30 to 59, the
seconds are reset to "00" and 1 is added to the minutes. If the second's count is in
the range of 00 to 29, the minute's count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press C to
increase the number. While the day of the week is selected, pressing C advances
to the next day. Holding down C changes the current selection at high speed.
5. After you set the time and date, press B to return to the Timekeeping Mode.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.