background image
2161/2251/2261-1
3. While the seconds digits are selected (flashing), press B
B
B
B
B to reset the seconds to
"00". If you press B
B
B
B
B while the seconds count is in the range of 30 to 59, the sec-
onds are reset to "00" and 1 is added to the minutes. If the seconds count is in the
range of 00 to 29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press B
B
B
B
B to in-
crease the number. Holding down B
B
B
B
B changes the number at high speed.
· To switch between the 12-hour and 24-hour formats, press D
D
D
D
D while some dig-
its are flashing.
5. After you set the time and date, press A
A
A
A
A to return to the Timekeeping Mode.
· The day of the week is automatically set in accordance with the date.
· The date can be set within the range of January 1, 1995 to December 31, 2039.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
About the backlight
When you switch the backlight function on, the backlight of the watch flashes when-
ever alarm, countdown alarm or hourly time signal is sounding.
· Pressing D
D
D
D
D at any time illuminates the display for about two seconds, regardless of
the backlight's on/off setting.
· The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
· Frequent use of the backlight shortens the battery life.
To switch the backlight function on and off
In the Timekeeping Mode, hold down B
B
B
B
B for one or two seconds to switch the back-
light function on and off. When you switch the backlight function on, an indicator
appears on the display as shown.
· The backlight function indicator remains on the display in all modes until you switch
the backlight function off.
· The above operation controls operation of the backlight function only. It does not
affect operation of audible tones and signals.
· The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transistor that vibrates when the EL panel lights up. It does not indicate
malfunction of the watch.
GENERAL GUIDE
· Press C
C
C
C
C to change from mode to mode. Each mode is explained in detail on the following pages.
· After you perform an operation in any mode, pressing C
C
C
C
C returns to the Timekeeping Mode.
· Press D
D
D
D
D in any mode to illuminate the display.
Timekeeping Mode
Alarm Mode
Stopwatch Mode
Countdown Alarm Mode
[Modules 2251, 2261]
[Module 2161]
Module No. 2161/2251/2261
TIMEKEEPING MODE
To set the time and date
1. Press A
A
A
A
A while in the Timekeeping Mode. The seconds
digits flash on the display because they are
selected.
2. Press C
C
C
C
C to change the selection in the following se-
quence.
Seconds
Day
Hour
Minutes
Year
Month
ALARM MODE
You can set an alarm with hour, minutes, month, and day.
When the alarm is on, the alarm sounds for 20 seconds at
the preset time. When the Hourly Time Signal is on, the
watch beeps every hour on the hour.
Alarm Types
The types of alarm you get depends on the information
you set.
· To set a daily alarm
Set the hour and minutes for the alarm time. Set "­" for
the month and "­ ­" for the day (see step 3 under "To
set the alarm time"). This type of setting causes the alarm
to sound every day at the time you set.
· To set a date alarm
Set the month, day, hour and minutes for the alarm time.
This type of setting causes the alarm to sound at the
specific time, on the specific date you set.
· To set a 1-month alarm
Set the month, hour and minutes for the alarm time. Set "­ ­" for the day (see step
3 under "To set the alarm time"). This type of setting causes the alarm to sound
every day at the time you set, only during the month you set.
· To set a monthly alarm
Set the day, hour and minutes for the alarm time. Set "­" for the month (see step 3
under "To set the alarm time"). This type of setting causes the alarm to sound
every month at the time you set, on the day you set.
To set the alarm time
1. Press A
A
A
A
A while in the Alarm Mode until the hour digits start to flash on the display.
The hour digits flash because they are
selected.
· At this time the alarm is automatically switched on.
2. Press C
C
C
C
C to change the selection in the following sequence.
Hour
Day
Minutes
Month
3. Press B
B
B
B
B to increase the selected digits. Holding down B
B
B
B
B changes the number at
high speed.
· The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4. After you set the alarm time, press A
A
A
A
A to return to the Alarm Mode.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To switch an alarm and Hourly Time Signal on and off
Press B
B
B
B
B while in the Alarm Mode to change the status of an alarm (see "Alarm Types")
and Hourly Time Signal in the following sequence.
Both off
Both on
Alarm only
Hourly Time Signal only
Month - Day
Minutes
Hour
Alarm on indicator
Mode
indicator
Hourly time
signal on
indicator
Hourly time signal
on indicator
Alarm on indicator
Backlight function
on indicator
PM indicator
Day of week
Month - Day
Seconds
Hour
Minutes
The operational procedures for Modules 2251, 2261 and 2161 are identical. All of the illustrations in this manual show Module 2161.


background image
2161/2251/2261-2
3. Press B
B
B
B
B to increase the selected number. Holding down B
B
B
B
B changes the number
at high speed.
· To set the starting value of the countdown time to 24 hours, set to 0:00' 00.
4. After you set the countdown time, press A
A
A
A
A to return to the Countdown Alarm Mode.
· If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode automatical-
ly.
To use the countdown timer
1. Press B
B
B
B
B while in the Countdown Alarm Mode to start the countdown timer.
2. Press B
B
B
B
B again to stop the countdown timer.
· You can continue countdown timer operation by pressing B
B
B
B
B.
3. Stop the timer and then press A
A
A
A
A until the countdown time is reset to its starting
value.
· When the end of the countdown is reached and auto repeat timing is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button. Count-
down timing stops, and the countdown time is automatically reset to its starting
value after the alarm stops.
To switch auto repeat timing on and off
1. Press A
A
A
A
A while in the Countdown Alarm Mode. The hours
digit flashes on the display because it is
selected.
2. Press D
D
D
D
D to switch auto repeat on and off.
3. Press A
A
A
A
A to return to the Countdown Alarm Mode.
· When the end of the countdown is reached while auto
repeat is on, the alarm sounds, but the starting count-
down time is reset and countdown timing starts again
automatically whenever the countdown reaches zero.
You can stop timing by pressing B
B
B
B
B, and manually reset
to the starting countdown time by pressing A
A
A
A
A.
Current time
Mode indicator
1/100 second
Minutes
Seconds
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes, 59.99 seconds.
To measure elapsed time
1. Press B
B
B
B
B to start the stopwatch.
2. Press B
B
B
B
B to stop the stopwatch.
· You can resume the measurement operation by press-
ing B
B
B
B
B again.
3. Press
A
A
A
A
A to clear the stopwatch to all zeros.
· For the first 60 minutes, the display shows minutes, sec-
onds, and 1/100 second. After 60 minutes, the display
format changes to show hours, minutes, and seconds.
To record split times
1. Press B
B
B
B
B to start the stopwatch.
2. Press A
A
A
A
A to display the timing up to that point. Stopwatch timing continues internal-
ly.
3. Press A
A
A
A
A to clear the split time and to continue time measurement on the display.
· You can repeat steps 2 and 3 as many times as you want.
4. Press B
B
B
B
B to stop the time measurement.
5. Press A
A
A
A
A to clear the stopwatch to all zeros.
To time first and second place finishes
1. Press B
B
B
B
B to start the stopwatch.
2. Press A
A
A
A
A when the first finisher crosses the line, and record the time.
3. Press B
B
B
B
B when the second finisher crosses the line.
4. Press A
A
A
A
A to display the finishing time of the second finisher.
5. Press A
A
A
A
A again to clear the stopwatch to all zeros.
COUNTDOWN ALARM MODE
The countdown timer can be set within a range of 1 sec-
ond to 24 hours. When the countdown reaches zero, an
alarm sounds for 10 seconds or until you press any but-
ton.
To set the countdown time
1. Press A
A
A
A
A while in the Countdown Alarm Mode. The hours
digit flashes on the display because it is
selected.
2. Press C
C
C
C
C to change the selection in the following se-
quence.
Seconds
Minutes
Hours
Current time
Minutes
Hours
Mode indicator
Seconds
Auto repeat on indicator