background image
1
Operation Guide 3750
MA0412-EA
About This Manual
· Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
· For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
· Button operations are indicated using the letters shown
in the illustration.
· Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
Timekeeping Mode
World Time Mode
Countdown Timer Mode
Stopwatch Mode
Alarm Mode
Hand Setting Mode
Press
.
General Guide
· Press C to change from mode to mode.
· In any mode, press B to illuminate the display.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
· In the Timekeeping Mode, you can press D to change the display format as shown
below.
Hour : Minutes Seconds
PM indicator
Day of the Week
Month ­ Day
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for summer time
(Daylight Saving time or DST), your Home City code (the code for the city where you
normally use the watch), and the 12/24-hour format.
· This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
· Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
· After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
Screen
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (ON) and
Standard Time (OF)
Change the Home City code
Change the hour or minutes
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Change the year
Change the month or day
Do this:
Press D.
Press D.
Use D (east) and B (west).
Use D (+) and B (­).
Press D.
Use D (+) and B (­).
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B and D to select the code you want.
· Make sure you select your Home City code before
changing any other setting.
· For full information on city codes, see the "City Code
Table".
3. Press C to move the flashing in the sequence shown below to select the other
settings.
Seconds
DST
Home City Code
Hour
Minutes
Day
Month
Year
12/24-Hour format
4. When the setting you want to change is flashing, use B and D to change it as
described below.
5. Press A to exit the setting screen.
· See "Digital Time Daylight Saving Time (DST) Setting" below for details about the
DST setting.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (ON
displayed) and Standard Time (OF displayed).
4. Press A to exit the setting screen.
· The DST indicator appears on the Month ­ Day screen
to indicate that Daylight Saving Time is turned on.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. Press D to advance the analog time setting by
20 seconds.
· Holding down D advances the analog time setting at
high speed.
· If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the high-
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm or countdown beeper)
starts to sound.
4. Press A to exit the setting screen.
· The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
· To return to the Timekeeping Mode, press C.
DST indicator


background image
2
Operation Guide 3750
City code
Current time for the
selected city code
World Time
World Time digitally displays the current time in 27 cities
(29 time zones) around the world.
· All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
In the World Time Mode, press D to scroll eastwardly
through city codes.
· For full information about city codes, see the "City Code
Table".
· If the current time shown for a city is wrong, it probably
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to the
Timekeeping Mode and make the necessary
adjustments.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D to display the city code
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
· The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
· Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
· Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as the
city code.
Seconds
Minutes
DST indicator
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
· All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
· See "To configure the countdown timer" for information
about setting up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is repeated
a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
· Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you can
press A to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
· When the progress beeper is turned off, the countdown end beeper sounds for
about 10 seconds, or until you press any button to stop it.
· When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
· Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
· 30 seconds before the end of the countdown, the watch emits four short beeps.
· The watch emits a short beep for each of the last 10 seconds of the countdown.
· If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
· If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start Time
Auto-repeat
Progress Beeper
Setting
Start Time
Auto-repeat
Progress Beeper
Screen
Button Operation
Use D (+) and B (­) to change the setting.
· You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
Press D to toggle auto-repeat on (
displayed) and off
(
displayed).
Press D to toggle the progress beeper on (ON) and off
(OF).
3. When the setting you want to change is flashing, use B and D to change it as
described below.
4. Press A to exit the setting screen.
· You can also perform steps 1 and 2 of the above procedure whenever you need to
view the current auto-repeat and progress beeper settings.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the
countdown timer.
· The countdown timer operation continues even if you
exit the Countdown Timer Mode.
· Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
· To completely stop a countdown operation, first pause it
(by pressing D), and then press A. This returns the
countdown time to its starting value.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
· The display range of the stopwatch is 59 minutes,
59.99 seconds.
· The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
· The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
· Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
· All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Start
Split
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split Time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Minutes
Seconds
1/100
seconds
Alarm number
Alarm time
(Hour : Minutes)
On/Off status
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
· There are six screens in the Alarm Mode. Four are for
one-time alarms (indicated by numbers from
AL1
through AL4), one is for a snooze alarm
(indicated by SNZ), and one is for the Hourly Time
Signal (indicated by SIG).
· All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
· To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
· The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
· This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (­) to change it.
· When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.


background image
3
Operation Guide 3750
Alarm Operation
The alarm sounds at the preset time for about 20 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
· To stop the alarm tone after it starts to sound, press any button.
· Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the SNZ setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
· Turning on a one-time alarm (AL1through AL4)
displays the alarm on indicator on its Alarm Mode
screen.
· Turning on the snooze alarm (SNZ) displays the alarm
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen.
· In all modes, the alarm on indicator is shown for any
alarm that is currently turned on.
· The alarm on indicator flashes while the alarm is
sounding.
· The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (SIG).
2. Press A to toggle it on (ON displayed) and off
(OF displayed).
· The Hourly Time Signal on indicator is shown on the
display in all modes while the Hourly Time Signal is
turned on.
On/Off status
Hourly time signal
on indicator
Alarm on indicator
On/Off status
Snooze alarm indicator
Mode
Timekeeping
World Time
Countdown Timer
Stopwatch
Alarm
Hand Setting
Graphic Area
Timekeeping Mode seconds
Timekeeping Mode seconds
Countdown time minutes
Stopwatch time seconds
No indication
No indication
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Graphic Area
The following describes the information indicated by the graphic area in each mode.
Graphic area
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically exits the setting screen.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Timekeeping
· Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
· With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
· With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
· The year can be set in the range of 2000 to 2039.
· The watch's built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch's batteries replaced.
World Time
· The World Time Mode times are calculated from the current Home City time setting
in the Timekeeping Mode, using the Greenwich Mean Time (GMT) differentials
associated with each city code.
· The GMT differential is a value that indicates the time difference between Greenwich
Mean Time and the time zone where a city is located.
· GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. In any mode, press B to illuminate the display for
about two seconds.
· The electro-luminescent panel that provides illumination loses power after very long
use.
· The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
· The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
· The backlight automatically turns off whenever an alarm sounds.
· Frequent use of the backlight shortens the battery life.
*Based on data as of June 2004.
­ ­ ­­11.0
Pago Pago
HNL
Honolulu
­10.0
Papeete
ANC
Anchorage
­09.0
Nome
LAX
Los Angeles
­08.0
San Francisco, Las Vegas, Vancouver, Seattle/Tacoma,
Dawson City
DEN
Denver
­07.0
El Paso, Edmonton
CHI
Chicago
­06.0
Houston, Dallas/Fort Worth, New Orleans,
Mexico City, Winnipeg
NYC
New York
­05.0
Montreal, Detroit, Miami, Boston, Panama City,
Havana, Lima, Bogota
CCS
Caracas
­04.0
La Paz, Santiago, Port Of Spain
RIO
Rio De Janeiro
­03.0
Sao Paulo, Buenos Aires, Brasilia, Montevideo
­ ­ ­­02.0
­ ­ ­­01.0
Praia
GMT
+00.0
Dublin, Lisbon, Casablanca, Dakar, Abidjan
LON
London
PAR
Paris
+01.0
Milan, Rome, Madrid, Amsterdam, Algiers,
Hamburg, Frankfurt, Vienna, Stockholm, Berlin
CAI
Cairo
+02.0
Athens, Helsinki, Istanbul, Beirut, Damascus,
JRS
Jerusalem
Cape Town
JED
Jeddah
+03.0
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
THR
Tehran
+03.5
Shiraz
DXB
Dubai
+04.0
Abu Dhabi, Muscat
KBL
Kabul
+04.5
KHI
Karachi
+05.0
Male
DEL
Delhi
+05.5
Mumbai, Kolkata
DAC
Dhaka
+06.0
Colombo
RGN
Yangon
+06.5
BKK
Bangkok
+07.0
Jakarta, Phnom Penh, Hanoi, Vientiane
HKG
Hong Kong
+08.0
Singapore, Kuala Lumpur, Beijing, Taipei, Manila,
Perth, Ulaanbaatar
TYO
Tokyo
+09.0
Seoul, Pyongyang
ADL
Adelaide
+09.5
Darwin
SYD
Sydney
+10.0
Melbourne, Guam, Rabaul
NOU
Noumea
+11.0
Port Vila
WLG
Wellington
+12.0
Christchurch, Nadi, Nauru Island
City
City
GMT
Other major cities in same time zone
Code
Differential
City Code Table