background image
fx-9860G SD
fx-9860G
User's Guide
http://world.casio.com/edu/
E


background image
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not appli-
cable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
·Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
·Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
·Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to
meet FCC emission limits.
Connector SB-62
Power Graphic Unit to Power Graphic Unit
USB connector that comes with the fx-9860G SD/fx-9860G
Power Graphic Unit to PC for IBM Machine
IBM is a registered trademark of International Business Machines Corporation.
Declaration of Conformity
Model Number:
fx-9860G SD/fx-9860G
Trade Name:
CASIO COMPUTER CO., LTD.
Responsible party: CASIO, INC.
Address:
570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.


background image
BEFORE USING THE CALCULATOR
FOR THE FIRST TIME...
This calculator does not contain any main batteries when you purchase it. Be sure to
perform the following procedure to load batteries, reset the calculator, and adjust the
contrast before trying to use the calculator for the first time.
1. Making sure that you do not accidently press the o key, slide the case onto the
calculator and then turn the calculator over. Remove the back cover from the calculator
by pulling with your finger at the point marked 1.
2. Load the four batteries that come with the calculator.
· Make sure that the positive (+) and negative (­) ends of the batteries are facing
correctly.
3. Remove the insulating sheet at the location marked "BACK UP" by pulling in the
direction indicated by the arrow.
4. Replace the back cover, making sure that its tabs enter the holes marked 2 and turn
the calculator front side up. The calculator should automatically turn on power and
perform the memory reset operation.
1
2
20050401


background image
P button
5. Press m.
· If the Main Menu shown to the right is not on the display,
open the back cover and press the P button located
inside of the battery compartment.
6. Use the cursor keys (
f, c, d, e) to select the SYSTEM icon and press
w, then press 1(
) to display the contrast adjustment screen.
7. Adjust the contrast.
· The
e cursor key makes display contrast darker.
· The
d cursor key makes display contrast lighter.
· 1(INIT) returns display contrast to its initial default.
8. To exit display contrast adjustment, press m.
20050401


background image
20050401
TURNING POWER ON AND OFF
USING MODES
BASIC CALCULATIONS
REPLAY FEATURE
FRACTION CALCULATIONS
EXPONENTS
GRAPH FUNCTIONS
DUAL GRAPH
DYNAMIC GRAPH
TABLE FUNCTION
Quick-Start