AIWA XPR232 - Owner's Manual Immediate Download

Highlighted letters in the text of this manual correspond to the illustrations.

PRECAUTIONS

To maintain good performance

· Do not use the unit in places which are extremely hot, cold, dusty or humid. In

particular, do not use or keep the unit in following places.

· in a high humidity area such as a bathroom

· near a heater

· in an area exposed to direct sunlight (e.g., inside a parked car, where it can

become extremely hot)

· near sources of strong magnetism, such as televisions, speakers, or magnets

· where there is a lot of movement or vibration, such as on a car dashboard or

an unstable shelf

· Do not open the battery compartment with wet hands.

·Wipe the unit thoroughly before inserting batteries and after use.

· Do not soak the unit in water.

· Before connecting the AC adaptor or the headphones etc., be sure to confirm

the power is off.

For safety

· Use only an AC adaptor whose rated output is DC 5-6 V, 250-300 mA.

· Do not attempt to disassemble the unit. Laser rays from the optical pickup are

dangerous to the eyes.

· Make sure that pins or other foreign object do not get inside the player.

·Take care not to drop the unit or subject it to strong shocks.

·To keep dust from the pickup lens, keep the disc compartment lid closed after

use. Never touch the lens.

· If you hear no sound when playing a disc, DO NOT turn the volume up high

because music could suddenly start at high volume. Turn the volume control to

the lowest level before starting playback and slowly turn it up to the desired

level.

Notes on listening with the headphones

· Listen at moderate volumes to avoid hearing damage.

· Do not wear the headphones while driving or cycling. It may create a traffic

hazard.

·You should use extreme caution or temporarily discontinue use in potentially

hazardous situations, such as walking, jogging, etc.

·Wear them properly; L is left, R is right.

Note on condensation

If the unit is suddenly moved from a cold place to a warm place, it may result in

condensation on the pickup lens and malfunction or playback difficulties.

Should this occur, leave the unit for a few hours, then try playback again.

USING ON DRY CELL BATTERIES A

Open the battery compartment and insert two size AA (LR6) alkaline

batteries with the

0 and 9 marks correctly aligned.

Battery replacement

The battery indicator in the display changes first from

, then to

according to the remaining power of the batteries. Replace the batteries when

lights. If the unit remains in use after

lights, "Lo-bAtt" appears and

operation stops.

Battery life (using alkaline batteries LR6)

The setting of the E·A·S·S switch

Battery life

Approx. 38 hours

Approx. 32 hours

Battery life may vary depending on conditions of use.

If the cover of the battery compartment comes off B

Notes on dry cell batteries

· Make sure that the

0 and 9 marks are correctly aligned.

· Do not mix different types of batteries, or an old battery with a new one.

·To prevent the risk of electrolyte leakage or explosions, never recharge the

batteries, apply heat to them, or take them apart.

· When not using the batteries, remove them to prevent needless battery wear.

· If liquid leaks from the batteries, wipe thoroughly to remove.

USING ON RECHARGEABLE BATTERIES C

· Be sure to use size AA Ni-Cd 1.2 V 700 mAh rechargeable batteries, which are

commercially available.

· Be sure to read the instructions of the purchased rechargeable batteries before

use.

· When using on rechargeable batteries for the first time, charge them until the

battery indicator goes out.

· Before charging the batteries, close the disc compartment. You cannot charge

the batteries while it is open.

1 Insert the optional rechargeable batteries with the

0 and 9 marks

correctly aligned.

2 Connect the optional AC adaptor.

1 to DC 5~6 V jack

2 to a wall outlet

3 Keep

sSTOP/OFF/CHARGE pressed for about 2 seconds to start

charging.

"C-on" appears and the battery indicator blinks.

When charging is completed, "OFF" flashes a few times, and the battery

indicator goes out. Recharging exhausted batteries takes about 6 hours.

After charging, disconnect the AC adaptor.

Time to recharge the batteries

Recharge the batteries when

lights. If the unit remains in use after

lights, "Lo-bAtt" appears and the current operation stops.

Force charging

When recharging stops after only few minutes or the batteries cannot be fully

recharged, press

sSTOP/OFF/CHARGE while pressing MODE to force charging.

· Do not activate the force charging on the unit when there is no battery inserted

or when dry cell batteries are inserted. Doing so may cause malfunction.

To stop charging

Press

sSTOP/OFF/CHARGE during charging.

Time to replace the batteries

Replace the batteries with new ones if they lost their capability to charge fully.

ATTENTION:

The product you have purchased can be powered by

nickel cadmium batteries which are recyclable. At the

end of their useful life, under various state and local

laws, it is illegal to dispose of these batteries into your

municipal waste stream.

Please call 1-800-289-2492 for information on how to

recycle these batteries.

USING ON AC HOUSE CURRENT

Connect the optional AC adaptor in the same way as when recharging the

batteries.

During operation on AC house current, all of the battery indicators turn off.

BEFORE PLAYBACK

Inserting a disc D

1 Slide the OPEN switch to open the disc compartment.

2 Place a disc in the center with the label side facing up.

3 Close the disc compartment.

To remove the disc

Hold the disc at its edge and pick it up while pressing the pivot gently.

Note

· The unit may not play a CD-R/RW disc that is recorded on personal computers or

some kinds of CD-R/RW recorders because of differences in recording platforms.

· Do not attach any adhesive label to either side (the recordable side or the labeled

side) of a CD-R/RW disc. It may cause malfunction.

XP-R232

COMPACT DISC PLAYER

OPERATING INSTRUCTIONS

8C-HC5-910-01

011120AMK-U-S

Printed in China

HOLD switch E

Release HOLD. a

When not using the unit, set HOLD to the hold position. b

Accidentally pressed buttons will not function.

ePLAY/PAUSE is pressed while HOLD is set to the HOLD position, "HOLd"

flashes in the display.

Turning the power on E

Press

ePLAY/PAUSE.

Power is turned on and playback starts.

· Pressing BAND also turns the power on.

Note

"Err" appears on the display in the following cases:

When you try to play the unit without a disc in the disc compartment.

When you play a disc placed upside-down or a defective disc.

Standby mode E

When an operation finishes, the unit goes into standby mode until the auto power

off function automatically turns off the power.

To enter standby mode, press

e PLAY/PAUSE to start playback, then press

sSTOP/OFF/CHARGE.

Turning the power off E

Press

sSTOP/OFF/CHARGE in standby mode.

· Pressing

sSTOP/OFF/CHARGE in tuner mode also turns the power off.

· If no new operations are done within 30 seconds from the end of last operation,

the power is turned off automatically. (Auto power off function)

Adjusting the sound F

Connect the supplied headphones to the PHONES/LINE OUT jack.

An amplified speaker system can be connected instead to enjoy the CD sound.

Volume

Turn VOLUME to adjust the volume level.

DSL

Press DSL for more powerful sound and deeper bass.

DSL

lights up.

Press DSL again to return to normal playback.

How to wear the headphones G

PLAYBACK H

1 Release HOLD.

2 Press

ePLAY/PAUSE.

Playback starts from the first track.

a track number

b elapsed playing time

Basic operation

To stop

Press

sSTOP/OFF/CHARGE.

To pause

Press

ePLAY/PAUSE.

To resume, press it again.

To search for the beginning

Press

r or t.

of a track

To locate a desired passage

Keep

r or t pressed.

Release the button at the start of desired passage.

Display during playback I

Press ENTER/DISPLAY repeatedly during playback.

With each press, the display changes as follows.

1 Track display and elapsed playing time (normal display)

2 Track display and remaining playing time of the track in play

3 Remaining number of tracks and remaining playing time

Note

· When the total remaining time of the programmed tracks is 100 minutes or over, the

time is not displayed.

· When the alarm is set, the remaining time of the alarm is displayed between 1 and

Resume function I

Set HOLD to RESUME.

"RESUME" appears, and you can start playback from the point where you stopped

playback by pressing

sSTOP/OFF/CHARGE.

When the resume function is on, all-track repeat is selected automatically.

To cancel resume play, set HOLD to OFF.

Note

· Resume play may start at a point up to about 30 seconds behind or ahead of the

stopped point. Resume play may not operate if you stopped within the last 30 seconds

of the final track.

· Resume play will be canceled if you open the disc compartment. If the unit is turned

off, resume play will not be canceled. In this case, be sure to set HOLD to OFF before

changing discs.

Random/Repeat play I

Press MODE repeatedly to change the play mode as follows.

: one-track repeat

: all-track repeat

3 RNDM/

: random repeat

4 RNDM: random

5 normal playback

Note

You cannot go back to the previous track by pressing

r during random play.

D 1

OPEN

YUC

ENGLISH

OWNER'S RECORD

For your convenience, record the model number and the serial number (you will

find it inside the battery compartment of your set) in the space provided below.

Please refer to them when you contact your Aiwa dealer in case of difficulty.

Model No.

XP-R232

Serial No.

NOTE

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Modifications or adjustments to this product, which are not expressly approved

by the manufacturer, may void the user's right or authority to operate this product.

This Class B digital apparatus complies with Canadian ICES-003.

MAINTENANCE

To clean the pickup lens

If the lens becomes dirty, the player will skip or not play. If this occurs, clean the

lens in the following manner.

·To remove dust or dry particles, first use a camera lens blower/brush to blow a

few times to loosen particles, then gently brush the lens clean. Finish by blowing

the lens again.

·To remove fingerprints, use a cotton swab dipped in lens cleaning solution.

Wipe gently from the center to the edge. Lens cleaning solution is commercially

available.

Note

Take care not to get too much solution on the swab, which could flow into the unit and

cause damage.

Pressing too strongly with the swab could scratch or break the lens.

To clean the discs

Before playing, wipe the disc from the center out with a cleaning cloth. After

playing, store the disc in its case.

SPECIFICATIONS

Tracking system

3-beam laser

Laser pickup

Semiconductor laser

D/A conversion

8-times oversampling digital filter + 1-bit DAC

Frequency response

20 20,000 Hz

Output

PHONES/LINE OUT jack (stereo mini-jack)

Frequency range

AM: 530/531 kHz 1,710/1,602 kHz

(10 kHz/9 kHz steps)

FM: 87.5 108 MHz

TV: 2 13 ch

WEATHER: 1 7 ch

Maximum output

12 mW + 12 mW (16 ohms at 1 kHz)

500 mV (47 k ohms at 1 kHz)

Power supply

DC 3 V using two size AA (LR6) alkaline batteries

DC 2.4 V using two optional rechargeable batteries

(Ni-Cd 1.2 V 700 mAh)

AC house current using the optional AC adaptor

Maximum outside dimensions

132.0 (W) × 26.0 (H) × 145.0 (D) mm

(51/4 × 1

1/16 × 53/4 in.)

(excluding projecting parts and controls)

Weight

Approx. 216 g

(7.6 oz.) excluding batteries

Accessories

Stereo headphones (1)

Specifications and external appearance of this unit are subject to change without notice.

PROGRAM PLAY J

Up to 24 tracks can be selected for program play.

1 Press ENTER/DISPLAY in standby mode to display "P-01".

2 Select the desired track by pressing

r and t.

a track number

b program number

3 Press ENTER/DISPLAY within 8 seconds.

If it is not pressed within 8 seconds, the track number changes to 00. Repeat

from step 2 again.

4 Repeat steps 2 and 3 to program more tracks.

5 Press

ePLAY/PAUSE to start program play.

To stop program play

Press

sSTOP/OFF/CHARGE.

To add tracks to the program

Repeat steps 1 through 3 in standby mode. You can add tracks to the end of the

program.

To erase the program

Press

sSTOP/OFF/CHARGE in standby mode.

To check the programmed tracks

Press ENTER/DISPLAY repeatedly in standby mode.

The number of each programmed track will be displayed in order of playback.

Note

· The program is also erased when the disc compartment is opened or the auto power

off function turns the power off.

· When 24 tracks are programmed, "P-FULL" appears, and no more tracks may be

added.

·You cannot go back to the previous track by holding

r pressed during program

play.

· Repeat play and random play can be performed during program play.

OTHER FUNCTIONS K

Alarm

Alarm beeps after a specified time.

1 Keep MODE pressed until "

" and the time flash.

2 Press

r or t to set the time.

Adjustable range: 1 to 90 (minutes)

Each time you press

r or t, the time changes by 1 minute. Holding

down

r or t changes the time by 10 minutes.

3 Press ENTER/DISPLAY.

The setting is completed. After the specified time, alarm beeps for about 30

seconds.

To display the time till the alarm beeps, press ENTER/DISPLAY.

To change the set time of the alarm, repeat step 1 and press MODE. Then

repeat steps 2 and 3.

To cancel the alarm, repeat step 1 above to display "

OFF" and press ENTER/

DISPLAY.

Note

· When the alarm is beeping, the sound of CD or radio is muted.

· The alarm may start beeping up to about a minute earlier or later than the set time.

E·A·S·S (Electronic Anti-Shock System)

The E·A·S·S 3× function reduces skipping or muting of the sound when the unit

is subjected to shock.

1 Keep MODE pressed until "

" and the time flash.

2 Press MODE again.

3 Press

r or t to select "12" or "48".

4 Press ENTER/DISPLAY.

or 12 lights up and the player keeps about 48 seconds or 12 seconds of

playback sound in its memory.

Note

· Before jogging with this unit, allow sufficient time for the memory buffer to fill up

completely (ideally about 20 seconds).

Continuous shock or vibration may cause the sound to be interrupted even if the

E·A·S·S 3× function is activated. This is normal and not a malfunction. Should you

experience an interruption in sound, stabilize the unit for a few seconds, then resume

your activity.

· When the E·A·S·S 3

× function is activated, motor noise is heard as the motor

periodically rotates at high speed during playback. This is not a malfunction.

· When you set the E·A·S·S to 12 , quality of sound will be better than when you set it

to 48 .

RADIO RECEPTION

Tuning in to a station L

1 Press BAND repeatedly to select the band (FM, AM, TV, or WEATHER).

2 Press

t or r to tune in to a station or to select a channel.

After listening, press

sSTOP/OFF/CHARGE to turn off the radio.

For quick tuning in to an FM or AM station

Keep either

t or r pressed for about 1 second. When a station is tuned in

to, the frequency stops automatically. However, it does not stop if the broadcast

signal is weak.

For better reception M

FM, TV, WEATHER: The headphone cord functions as the FM antenna. Keep it extended.

AM: Turn the unit to find the position which gives the best reception.

Listening to FM stereo broadcast

When a tuned in station is in stereo, "

" lights up.

When the FM stereo signal is weak and distorted, press MODE. "ST" goes out

and the sound will be heard in monaural but distortion will be reduced.

Note

· Do not open the disc compartment during radio reception. The buttons will be

deactivated.

· The power is turned off automatically if no operation is made after about 2.5 hours

from the last operation during radio reception.

Changing AM steps N

Broadcasts have different frequency steps in different countries.

This unit is factory-set to 10 kHz steps. When using the unit where the AM step

is 9 kHz, change it as follows.

1 When the power is off, keep MODE pressed and hold down BAND until

"10 StEP" appears.

2 Press MODE repeatedly to select "9".

3 Press ENTER/DISPLAY.

"BUSY" appears for about 4 seconds and the setting will be changed.

To resume to 10 kHz, change in the similar way.

Note

When the AM step is changed, preset stations are erased.

PRESETTING STATIONS

Automatic presetting O

You can preset up to a total of 30 stations on FM and AM.

1 Release HOLD.

2 Press BAND to turn on the radio.

3 Press

t or r to exit preset mode.

4 Keep ENTER/DISPLAY pressed for more than 2 seconds.

The unit searches for and memorizes the receivable stations.

Automatic presetting ends when all received stations are preset or when the

number of preset stations reach 30. Then, "BUSY" appears for about 4 seconds.

To stop automatic presetting, press

sSTOP/OFF/CHARGE.

If there is a station you wish to skip during presetting

When a station is tuned in, scanning stops and the tuned station is heard for

5 seconds. Press

t within these 5 seconds to skip this station.

Note

· When broadcast signals are very weak, stations cannot be preset automatically. Preset

them manually.

· "P-FULL" appears if you try to preset over 30 stations.

Manual presetting P

You can preset up to a total of 30 stations on FM and AM.

1 Press BAND repeatedly to select the band.

2 Press

t or r to tune in to a station.

3 Press ENTER/DISPLAY to preset the station.

a Preset number

To preset more stations, repeat steps 2 and 3.

Listening to preset stations Q

1 Press BAND repeatedly to select FM or AM.

2 Press PRESET CALL UP

i/DOWNk repeatedly to select the preset

number.

After listening, press

sSTOP/OFF/CHARGE to turn off the radio.

Changing the presetting

1 Press PRESET CALL UP

i/DOWNk repeatedly to select the preset

number you wish to change.

2 Keep ENTER/DISPLAY pressed for 1 or more seconds until the preset

number flashes.

3 While the preset number is flashing, press

t or r to tune in to a

station.

4 Press ENTER/DISPLAY to preset the station on the selected preset

number.

If the flashing stops, repeat from step 2.

Erasing the presettings one by one

Press

sSTOP/OFF/CHARGE after step 2 in "Changing the presetting" above.

"BUSY" appears for about 4 seconds and each preset station is erased. All preset

numbers move up by one and the preset numbers are refreshed.

Erasing all of the presetting

Change AM step. (See "Changing AM steps")

CONNECTING TO AN EXTERNAL UNIT

To PHONES/LINE OUT jack R

Use a commercially available connection cord which has a ø3.5 mm stereo mini-

plug at one end and two phono plugs at the other end.

Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and

connect the phono plugs to the analog input terminals of the external unit, such

as the amplifier or the equipment with a built-in amplifier. The CD sound can be

heard through the connected audio system.

Note

·Turn off the power of both units before connection.

· DO NOT connect to the PHONO inputs of an amplifier (with a built-in phonoequalizer-

amplifier).

· Adjust the volume and DSL on this unit.