CD Stereo System
8C-NFT-903-01
020520AKH-U-BF
U
NSX-TR77
En (English)
E (Español)
F (Français)
OPERATING INSTRUCTIONS
MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
OWNER'S RECORD
Record the model number and serial number of your set (found at the
rear of your set) below. Refer to them when contacting your Aiwa dealer.
Model No. _____________________________
Serial No. _____________________________
For assistance and information
(United States and Puerto Rico)
2
En
WARNING
To reduce the risk of fire or electric shock, do not expose
this appliance to rain or moisture.
Explanation of Graphical Symbols:
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT SAFETY INSTRUCTIONS
Read the Operating Instructions carefully and completely
before operating the unit. Be sure to keep the Operating
Instructions for future reference. All warnings and cautions
in the Operating Instructions and on the unit should be
strictly followed, as well as the safety suggestions below.
Warning
To prevent electric shock or injury, these safety instructions
should be followed in the installation, use and servicing the
unit.
Installation
Attachments - Do not use attachments not recommended
by the unit manufacturer as they may result in the risk of
fire, electric shock or injury to persons.
Water and Moisture - Do not use this unit near water - for
example, near a bathtub, washbowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool, and the like.
Heat - Do not use this unit near sources of heat, including
heating vents, stoves, or other appliances that generate heat.
It also should not be placed in temperatures less than 5°C
(41°F) or greater than 35°C (95°F ).
Mounting surface - Place the unit on a flat, even surface.
Accessories - Do not place this unit on an unstable cart,
stand, tripod, bracket, or table. The unit may fall, causing
serious injury to a child or an adult, and serious damage to
the appliance. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the
unit. Any mounting of the appliance should follow the
manufacturer's instructions, and should use a mounting
accessory recommended by the manufacturer.
Portable cart - An appliance and cart
combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Ventilation - The unit should be situated with adequate
space around it so that proper heat ventilation is assured.
Allow 10 cm clearance from the rear and the top of the unit,
and 5 cm from the each side.
Slots and openings in the cabinet and the back or bottom
are provided for ventilation, and to ensure reliable operation
of the unit and to protect it from overheating, these openings
must not be blocked or covered. The openings should never
be blocked by placing the unit on a bed, sofa, rug or other
similar surface. This unit should not be placed in a built-in
installation such as a bookcase unless proper ventilation is
provided.
Object and Liquid Entry - Never push objects of any kind
into this unit through the cabinet slots as they may touch
dangerous voltage points or short-circuit parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the unit.
Electric Power
Power Sources - This unit should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your appliance dealer or local power company. To
operate unit on battery power, or other sources, refer to the
operating instructions.
Grounding or Polarization - This unit is provided with a
polarized alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the plug.
If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
Power-Cord Protection - Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the product.
3
En
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........ 2
PREPARATIONS .................................. 4
PARTS AND CONTROLS ......................... 5
ADJUSTMENTS BEFORE OPERATIONS ....... 8
CD OPERATIONS ............................... 10
RADIO OPERATIONS ........................... 12
TAPE OPERATIONS ............................. 14
SOUND ADJUSTMENTS ....................... 17
TIMER OPERATIONS ........................... 18
REFERENCE ..................................... 20
System and accessories
NSX-TR77
CX-NTR77 CD stereo cassette receiver
SX-NTR77 Front speakers
Remote control
FM antenna
AM antenna
Overloading - Do not overload wall outlets, extension
cords, integral convenience receptacles as this can result in
a risk of fire or electric shock.
Outdoor Antenna
Power lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the unit, be sure the antenna
or cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Section
810 of the National Electrical Code, ANSI/NFPA No.70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
See the figure.
Lightning
For added protection for this unit receiver during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to
the unit due to lightning and powerline surges.
Maintenance
Cleaning - Unplug this unit from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Damage Requiring Service
Unplug this unit from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
-When the power cord or plug is damaged.
- If liquid has been spilled, or objects have fallen into the unit.
- If the unit has been exposed to rain or water.
- If the unit does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the unit to normal operation.
- If the unit has been dropped or the cabinet has been damaged.
-When the unit exhibits a distinct change in performance -
this indicates a need for service.
Do not attempt to service this unit yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or having the same
characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
Safety Check - Upon the completion of any service or repairs
to this unit, ask the service technician to perform safety checks
to determine that the unit is in proper operating condition.
4
En
Connection
Plug in the AC power cord to the AC power outlet after all
other connections are made.
1 Connect the front speakers.
Connect the right front speaker to the SPEAKERS R
terminals and place it on the right side of the unit.
Connect the left to the SPEAKERS L terminals and place
it on the left side.The speaker cords with the white stripes
go to the 0 terminals.
PREPARATIONS
Remote control
Detach the battery compartment lid at the rear of the remote
control and insert two R6 (size AA) batteries with correct
polarity.
·Replace the batteries with new ones when the operational
distance between the remote control and main unit
becomes shorter.
·Remove the batteries if the unit is not going to be used for
an extended period of time.
·The remote control may not operate if it is used under
intense sunlight, etc., or if its line of sight is obstructed.
AM antenna
FM antenna
2 Connect the supplied antennas.
Strip off the insulation of the FM antenna with twisting
the cord.
Connect the FM antenna to the FM 75 terminal with
the
mark and the AM antenna to the AM LOOP
terminals.
3 Connect the AC power cord to an AC outlet.
When the AC power cord is connected to an AC outlet
for the first time, DEMO appears on the display.
To deactivate the DEMO, press c.
·Do not short-circuit the 0 and 9 speaker cord leads.
·Do not leave objects generating magnetism or objects
affected by magnetism near the speakers.
5
En
Main unit: rear
1 AM LOOP, FM 75 terminals
Plug in the supplied AM and FM antennas here.
2 VIDEO/AUX jacks
Accepts analog sound signals from external equipment.
Connect using an optional connecting cable with RCA
phono plugs (red plug to R jack, white plug to L jack).
Refer also to the operating instructions of your
equipment.
To switch function to external input, press VIDEO/AUX.
Tip:
To change the displayed name for this function, turn
the unit on, then hold down VIDEO/AUX and press
POWER on the unit. Repeat the procedure to select
"AUX", "VIDEO" or "TV".
3 SPEAKERS3 terminals
Connect the speaker cord of the supplied front speakers
here.
4 AC power cord
PARTS AND CONTROLS
Dynamic Integrated Neo Amplifier
is a brand-new amplifier system where clear mid-to-high
range frequency sound, as well as rich low frequency sound,
can be reproduced and listeners can enjoy the close-to-
original sound with less distortion at either high or low
volume levels.