TORINITORON® COLOR GRAPHIC DISPLAY
0.24 mm aperture grille pitch(center)
17 inches measured diagonally
Viewable image size
× 243 mm (w/h)
Horizontal: 1600 dots
Vertical: 1200 lines
Horizontal: 1024 dots
Vertical: 768 lines
Standard image area
AC input voltage/current
100 to 240 V, 50/60 Hz, Max. 1.7A
Approx. 115 W
× 418 × 421mm (w/h/d)
× 16 1/2 ×16
Approx. 19 kg (41.9 lb 1 oz)
Plug and Play
Supplied accessories Power cord(1)
Notes on cleaning the screen's surface(1)
*Recommended horizontal and vertical timing condition
·Horizontal sync width should be more than 1.0
·Horizontal blanking width should be more than 3.0
·Vertical blanking width should be more than 500
**If the input signal is Generalized Timing Formula(GTF)
compliant, the GTF feature of the monitor will automatically
provide an optical image for the screen.
Design and specification are subject to change without notice.
× 234 mm (w/h)
× 9 1/4 inches)
Horizontal: 30 to 85 kHz
Vertical: 48 to 170 Hz
Approx. 406 mm (16.0 inches)
Chassis No. SCC-L38A-A
The AC leakage from any exposed metal part to earth ground and from all
exposed metal parts to any exposed metal part having a return to chassis,
must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-
540A. Follow the manufacturers' instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital
multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or
battery-operated AC voltmeter. The "limit" indication is 0.75 V, so
analog meters must have an accurate low-voltage scale. The Simpson 250
and Sanwa SH-63Trd are examples of a passive VOMs that are suitable.
Nearly all battery operated digital multimeters that have a 2 V AC range
are suitable. (See Fig. A)
After correcting the original service problem, perform the following safety
checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
2. Check the interboard wiring to ensure that no wires are "pinched" or
contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and
mounting hardware have been replaced. Be absolutely certain that you
have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that
were installed during a previous repair. Point them out to the customer
and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
6. Check the line cords for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values. Make sure your
instruments are accurate; be suspicious of your HV meter if sets always
have low HV.
8. Check the antenna terminals, metal trim, "metallized" knobs, screws, and
all other exposed metal parts for AC Leakage. Check leakage as
Fig. A. Using an AC voltmeter to check AC leakage.
To Exposed Metal
Parts on Set
NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE
DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
! ON THE
SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUST-
MENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE
IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES
WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IM-
PROPER OPERATION IS SUSPECTED.
NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE
DEMAGNETISATION EST ENLEVÉE.
ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE
! SONT CRITIQUES POUR LA SÉCURITÉ. NE LES
REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO
SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L'IMPORTANCE EST
CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT
IDENTIFIÉS DANS LE PRÉSENT MANUEL.
PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE
FONCTIONNEMENT EST SUSPECTÉ.
POWER SAVING FUNCTION
This monitor meets the power-saving guidelines set by VESA, TCO'99,
ENERGY STAR. If no signal is input to the monitor from your
computer, the monitor will automatically reduce power consumption as
*1 When your computer enters power saving mode, NO SIGNAL appears
on the screen. After a few seconds, the monitor enters power saving
*2 "Deep sleep" is power saving mode defined by the Environmental
115 W (without USB operation)
0 W (approximately)
Horizontal / Vertical Deflection failure,
Aging / Self Test
Out of scan range
Green (OSD indication)
Aging Mode (Video Aging)
During Power Save, press MENU button for longer than 2 second.
Monitor Information and RGB bar :
During Power Save, push CONT+ button for longer than 2 second.
During Power Save, push CONT- button for longer than 2 second.