Enter below the Model No. and Serial No.
which are located either on the rear, bot-
tom or side of the cabinet. Retain this
information for future reference.
VICTOR COMPANY OF JAPAN, LIMITED
UX-T550
MICRO COMPONENT SYSTEM
UX-T151/T150
MICRO
COMPONENT
SYSTEM
INSTRUCTIONS
Printed in China
1000MZMCREJSC
NEDERLANDS
ESPAÑOL
DEUTSCH
ENGLISH
GNT0001-001A
[B]
For Customer Use:
Model No.
Serial No.
EN
General
Power output
: 28 W (14 W + 14 W) at 4
(Max.)
20 W (10 W + 10 W) at 4
(10% THD)
Input terminals
: AUX IN (300 mV/47 k
)
Output terminals
: PHONES (Output level: 0-15 mW/ch, 32
, Matching
impedance: 16
- 1 k)
SPEAKER (Matching impedance 4
- 16 )
Power requirements : AC 230 V, 50 Hz
Ext. DC 12V (car battery via optional CA - R120E car
adapter)
Power consumption
: 35 W (with
button ON)
2.8 W (with
button STANDBY)
Dimensions
: 404 (W) x 209 (H) x 270 (D) mm, including knobs
Mass
: Approx. 6.5 kg
Accessories provided : Power cord x 1
Remote control unit (RM-RXUT100) x 1
"R6/AA (15F)" batteries x 2 (for the remote control)
FM wire antenna x 1
Loop antenna stand x 1
Design and specifications are subject to change without notice.
SPECIFICATIONS
CD player section
Type
: Compact disc player
Signal detection
system
: Non-contact optical pickup
Number of channels : 2 channels
Frequency response : 20 Hz - 20,000 Hz
Signal-to-noise ratio : 90 dB
Wow & flutter
: Less than measurable limit
Radio section
Frequency range
: FM 87.5 - 108 MHz
AM (MW) 522 - 1,629 kHz
AM (LW) 144 - 288 kHz
Antennas
: Loop antenna for AM (MW/LW)
External antenna terminal for FM (75
)
Tape deck section
Track system
: 4-track 2-channel stereo
Motor
: Electronic governor DC motor for capstan
Heads
: Hard permalloy head for recording/playback, 2 gap
ferrite head for erasure (Combination head)
Frequency response : 60 - 15,000 Hz (with CrO2 tape)
Wow & flutter
: 0.15% (WRMS)
Fast wind time
: Approx. 130 sec (C-60 cassette)
Speaker Section (each unit)
Speakers
(Impedance)
: 8 cm (4
),
Dimensions
: 131 (W) x 203 (H) x 194 (D) mm
Mass
: Approx. 1.6 kg
UX-T550(B)_cover1-4.pm6
12/12/00, 3:10 PM
1
G-1
IMPORTANT (In the United Kingdom)
Mains Supply (AC 230 V
Ó, 50 Hz only)
DO NOT cut off the mains plug from this equipment. If the plug fitted is not
suitable for the power points in your home or the cable is too short to reach
a power point, then obtain an appropriate safety approved extension lead or
consult your dealer.
BE SURE to replace the fuse only with an identical approved type, as
originally fitted, and to replace the fuse cover.
If nonetheless the mains plug is cut off ensure to remove the fuse and
dispose of the plug immediately, to avoid a possible shock hazard by
inadvertent connection to the mains supply.
IMPORTANT
DO NOT make any connection to the terminal which is marked with the letter
E or by the safety earth symbol or coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in accordance
with the following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
As these colours may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the terminal which
is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
IF IN DOUBT -- CONSULT A COMPETENT ELECTRICIAN.
IMPORTANT FOR LASER PRODUCTS
PRECAUTIONS
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the rear cover. There are no user service-
able parts inside the unit; leave all servicing to qualified service per-
sonnel.
4. CAUTION: The CD player uses invisible laser radiation and is
equipped with safety switches which prevent the emission of radia-
tion when the CD holder or CD tray is open. It is dangerous to defeat
the safety switches.
5. CAUTION: Use of controls for adjustments and the performance of
procedures other than those specified herein may result in expo-
sure to hazardous radiation.
G-1
SAFETY PRECAUTIONS
Prevention of Electric Shocks, Fire Hazards and Damage
1. Even when the
button is set to STANDBY, a very small current
will flow. To save power and for safety when not using the unit for an
extended period of time, disconnect the power cord from the house-
hold AC outlet.
2. Do not handle the power cord with wet hands.
3. When unplugging from the wall outlet, always grasp and pull the
plug, not the power cord.
4. Consult your nearest dealer when damage, disconnection, or con-
tact failure affects the cord.
5. Do not bend the cord severely, or pull or twist it.
6. Do not modify the power cord in any manner.
7. To avoid accidents, do not remove screws to disassemble the unit
and do not touch anything inside the unit.
Caution
switch!
Disconnect the mains plug to shut the power off completely. The
switch in any position does not disconnect the mains line. The power
can be remote controlled.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.Do not remove screws, covers or cabinet.
2.Do not expose this appliance to rain or moisture.
WARNING
The unit contains a built-in lithium battery for memory back-up that must
only be replaced by suitably qualified service personnel.
For battery replacement, take the unit to your dealer or a JVC service
station.
Caution:
This production contains a laser component
of higher laser class than Class 1.
DANGER: Invisible
laser radiationwhen
open and interlock failed
ordefeated.AVOIDDIRECT
EXPOSURE
ADVARSEL:Usynliglaser-
str ling ved bning, n r
sikkerhedsafbrydereerude
af funktion.Undg uds t-
telse for str ling.
(d)
VARNING:Osynliglaser-
str lning n r denna del
r ppnadochsp rren r
urkopplad. Betrakta ej
str len.
(s)
VARO: Avattaessa jasuo-
jalukitus ohitettaessa olet
alttiina n kym tt m lle
lasers teilylle. l katso
s teeseen.
(f)
REPRODUCTION OF LABELS AND THEIR LOCATION
Name/Rating plate
8. Do not insert any metallic objects into the unit.
9. Unplug the power cord when there is a possibility of lightning.
10.Do not use this apparatus in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as
cosmetics or medicines, flower vases, potted plants, cups, etc.) on
top of this apparatus.
11.Do not block the ventilation opcnings or holes. (If the ventilation open-
ings or holes are blocked by a newspaper or cloth, etc., the heat
may not be able to get out.)
12.Do not place any naked flame sources, such as lighted candles, on
the apparatus.
13.When discarding batteries, environmental problems must be con-
sidered and local rules or laws governing the disposal of these bat-
teries must be followed strictly.
Caution:
Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, lo-
cate the apparatus as follows:
1. Front:
No obstructions and open spacing.
2. Sides/Top/Back:
No obstructions should be placed in the areas shown by the di-
mensions below.
3. Bottom:
Place on a level surface. Maintain an adequate air path for ven-
tilation by placing on a table with a height of 10 cm or more.
Side view
Front view
1cm
1cm
15 cm
15 cm
15 cm
15 cm
10 cm
15 cm
AUX
UX-T550
UX-T550
UX-T550(B)_Safety.pm6
12/12/00, 3:12 PM
1
G-2
SAFETY INSTRUCTIONS
"SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT"
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment, care must be taken
if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are
properly made and in accordance with the manufacturer's instructions. Switch off and withdraw the mains plug when making or changing connec-
tions.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON'T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any wayswitch off, withdraw the
mains plug and consult your dealer.
DON'T remove any fixed cover as this may expose dangerous voltages.
DON'T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON'T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch
television whilst driving.
DON'T listen to headphones at high volume as such use can permanently damage your hearing.
DON'T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON'T use makeshift stands and NEVER fix legs with wood screws -- to ensure complete safety always fit the manufacturer's approved stand or
legs with the fixings provided according to the instructions.
DON'T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
-- NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal electrical
shock.;
-- NEVER guess or take chances with electrical equipment of any kind
-- it is better to be safe than sorry!
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
UX-T550(B)_Safety.pm6
12/12/00, 3:12 PM
2
1
Thank you for purchasing this JVC product. Please read these instructions carefully before starting operation to be sure to obtain optimum
performance and a longer service life from the unit.
CONTENTS
Features ..................................................................... 1
Handling precautions ............................................... 1
Connections .............................................................. 2
Power supply ............................................................. 4
Names of parts and their functions ......................... 5
Remote control unit .................................................. 6
Switching the power on/off ...................................... 6
Volume, tone and other controls ............................. 7
Handling CDs ............................................................. 7
Playing CDs ............................................................... 8
Handling cassette tapes ......................................... 10
Cassette playback ................................................... 10
Radio reception ....................................................... 11
Recording ................................................................ 12
Clock adjustment .................................................... 13
Timer operations ..................................................... 14
Maintenance ............................................................ 16
Troubleshooting ...................................................... 16
Specifications ............................................ Back page
FEATURES
CD-size micro component system consisting of 3 units
Active Hyper-Bass PRO circuit for low-frequency sound reproduction
One-touch operation (COMPU PLAY)
35-key remote control unit operates all CD, cassette deck and tuner
functions
Multi-function CD player
Programmed play of up to 20 tracks
Repeat Play
Random Play
U-Turn auto-reverse full-logic mechanism
Auto tape select mechanism
Metal (type IV) and CrO2 (type II) tape can be played back for supe-
rior tone quality
CrO2 (type II) tape recording capability
2-band digital synthesizer tuner with 45-station (30 FM and 15 AM
(MW/LW)) preset capability
Seek/manual tuning
Auto preset tuning
Timer/Clock function
Timer on/off with preset volume function
Sleep timer can be set for up to 120 minutes
HANDLING PRECAUTIONS
1. Avoid installing in the following places
Where it could be subject to vibrations.
Where it is excessively humid, such as in a bathroom.
Where it could be magnetized by a magnet or speaker.
2. Pay attention to dust
Be sure to close the CD holder or CD tray so that dust does not
collect on the lens.
3. Condensation
In the following cases, condensation may occur in the unit, in which
case the unit may not operate correctly.
In a room where a heater has just been switched on.
In a place where there is smoke or high humidity.
When the unit is moved directly from a cold to a warm room.
In these cases, set the
button to STANDBY and wait 1 or 2
hours before use.
4. Volume setting
CDs produce very little noise compared with analog sources. If the
volume level is adjusted for these sources, the speakers may be
damaged by the sudden increase of output level. Therefore, lower
the volume before operation and adjust it as required during play.
Do not use this unit in direct sunlight where it would be exposed to high temperatures above 40°C (104°F).
5. Safety mechanism
This unit incorporates a safety interlock mechanism which switches
the laser beam on and off, so that when the CD holder or CD tray is
open, the laser beam stops automatically.
6. Do not place cassette tapes, etc. near the speakers
Since there are magnets in the speakers, do not place tapes or mag-
netic cards on them as recorded data could be erased.
7. Keep this unit away from your TV
When this unit is used near a TV, the TV picture could be distorted.
If this happens, move this unit away from the TV. If this does not
correct the situation, avoid using this unit when the TV is turned on.
8. Cleaning the cabinet
If the cabinet gets dirty, wipe it with a soft, dry cloth. Never use
benzine or thinner as these could damage the surface finish.
9. When listening with headphones
Do not listen at high volumes as this could damage your hearing.
For safety, do not drive while listening to this unit.
UX-T550(B)_body.pm6
12/12/00, 3:11 PM
1
2
CONNECTIONS
Do not switch the power on until all connections are completed.
Antenna connection and adjustment
AM (MW/LW) loop antenna adjustment
Keep the loop antenna away from the unit and install it so that the best reception is obtained. (Do not leave the antenna wire in a bundle.)
ÓAC IN
RIGHT
R
L
LEFT
DC IN
12V
--
FM
AM LOOP
AM EXT
COAXIAL
75
Insert in the direction of the arrow.
AM (MW/LW)loop antenna (provided)
ÓAC IN
RIGHT
R
L
LEFT
DC IN
12V
FM antenna connections and adjustments
FM wire antenna (provided)
FM outdoor antenna (option)
Coaxial cable
Notes:
Do not place the loop antenna on a metal desk or near a TV or per-
sonal computer.
Installing an outdoor antenna requires expertise; we recommend that
you consult an audio dealer.
Install the antenna cord away from the power and speaker cords as
these could generate noise. Do not install the loop antenna so that it
touches the rear of the unit.
Use an outdoor antenna when stable reception cannot be obtained with the provided antenna.
UX-T550(B)_body.pm6
12/12/00, 3:11 PM
2