background image
SERVICE MANUAL
COLOR TELEVISION
20A42
FILE NO. 050-200209
DOCUMENT CREATED IN JAPAN, Jun., 2002


background image
SERVICING NOTICES ON CHECKING
6. AVOID AN X-RAY
1. KEEP THE NOTICES
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THE
CATHODE-RAY TUBE
Safety is secured against an X-ray by consider-
ing about the cathode-ray tube and the high
voltage peripheral circuit, etc.
Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
make sure not modify the circuit.
Repairing except indicates causes rising of high
voltage, and it emits an X-ray from the cathode-
ray tube.
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.
IMPORTANT
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an
electric shock while the electric current is
flowing.
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
4. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
In the condition that an explosion-proof cathode-
ray tube is set in this equipment, safety is
secured against implosion. However, when
removing it or serving from backward, it is
dangerous to give a shock. Take enough care to
deal with it.
PERFORM A SAFETY CHECK AFTER
SERVICING
7.
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
1.
2.
3.
4.
Unplug the plug from the AC outlet.
Remove the antenna terminal on TV and turn
on the TV.
Insulation resistance between the cord plug
terminals and the eternal exposure metal
[Note 2] should be more than 1M ohm by
using the 500V insulation resistance meter
[Note 1].
If the insulation resistance is less than 1M
ohm, the inspection repair should be
required.
[Note 1]
If you have not the 500V insulation
resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal
Earphone jack


background image
GENERAL SPECIFICATIONS
G-1
TV
CRT
CRT Size / Visual Size
20 inch / 508.0mmV
System
CRT Type
Normal
Deflection
90
degree
Magnetic Field
BV/BH
+0.45G/0.18G
Color System
NTSC
Speaker
2Speaker
Position
Front
Size
2 x 4.7 Inch
Impedance
8
ohm
Sound Output
MAX
2.5+2.5 W
10%(Typical)
2.0+2.0 W
NTSC3.58+4.43 /PAL60Hz
No
G-2
Tuning
Broadcasting System
US
System M
System
Tuner and
System
1Tuner
Receive CH
Destination
Ohers
Tuning System
F-Synth
Input Impedance
VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage
A - I, J - W, W+1 - W+84
Intermediate
Picture(FP)
45.75MHz
Frequency
Sound(FS)
41.25MHz
FP-FS
4.50MHz
Preset CH
No
Stereo/Dual TV Sound
Yes
Tuner Sound Muting
Yes
G-3
Power
Power Source
AC
120V AC 60Hz
DC
Power Consumption
at AC
90 W at AC 120 V 60 Hz
Stand by (at AC)
5
W at AC 120 V 60 Hz
Per Year
--
kWh/Year
Protector
Power Fuse
Yes
G-4
Regulation
Safety
UL
Radiation
FCC
X-Radiation
DHHS
G-5
Temperature
Operation
+5oC ~ +40oC
Storage
-20oC ~ +60oC
G-6
Operating Humidity
Less then 80% RH


background image
GENERAL SPECIFICATIONS
G-7
On Screen
Menu
Yes
Display
Menu Type
Character
Picture
Yes
Contrast
Yes
Brightness
Yes
Color
Yes
Tint
Yes
Sharpness
Yes
Audio
Yes
Bass
Yes
Treble
Yes
Balance
Yes
BBE On/Off
No
Stable Sound On/Off
No
CH Set Up
Yes
TV/CABLE(CATV)
Yes
Auto CH Memory
Yes
Add/ Delete
Yes
Lock
Yes
Language
Yes
V-chip
Yes
CH Label
No
Favorite CH
No
Color Stream DVD/DTV
No
Control Level
Yes
Volume
Yes
Brightness
Yes
Contrast
Yes
Color
Yes
Tint (NTSC Only)
Yes
Sharpness
Yes
Tuning
No
Bass
Yes
Treble
Yes
Balance
Yes
Back Light
No
Stereo,Audio Output,SAP
Yes
Video
Yes
Color Stream
No
Channel(TV/Cable)
Yes
CH Label
No
Game Timer
Yes
Sleep Timer
Yes
Sound Mute
Yes
V-chip Rating
Yes
G-8
OSD Language
English
French
Spanish
OSD Language Setting
English
G-9
Clock and
Sleep Timer
Max Time
120 Min
Timer
Step
10
Min
On/Off Timer
Program(On Tim / Off Tim)
No
Wake Up Timer
No
Timer Back-up (at Power Off Mode)
more than
--
Min
Sec


background image
GENERAL SPECIFICATIONS
G-10
Remote
Unit
RC-EH
Control
Glow in Dark Remocon
Yes
Format
Toshiba
Custom Code
40-BF h
Power Source
Voltage(D.C)
3V
UM size x pcs
UM-4 x 2 pcs
Total Keys
28
Keys
Keys
Power
Yes
1
Yes
2
Yes
3
Yes
4
Yes
5
Yes
6
Yes
7
Yes
8
Yes
9
Yes
0
Yes
100
No
CH Up
Yes
CH Down
Yes
Volume Up
Yes
Volume Down
Yes
TV/Caption/Text
Yes
CH1/CH2
Yes
TV/Video(TV/AV)
Yes
CH RTN/CH ENT(Quick View)
Yes
Sleep
Yes
RE Call(Call)
Yes
Reset
Yes
Menu
Yes
Enter
Yes
Mute
Yes
Exit
No
MTS(Audio Select)
Yes
Set +
Yes
Set -
Yes
Multi Brand Keys
CH Up(VCR)
No
CH Down(VCR)
No
Pause/Still
No
TV/VCR(VCR)
No
Code
No
FF
No
Rew
No
Rec
No
Play
No
Stop
No
TV
No
VCR
No
Cable
No