background image
OWNER'S MANUAL
MANUEL DU PROPRIÉTAIRE
MANUAL DEL USUARIO
9A09751900
AG-10D
AV Digital Home Theater Receiver
Z


background image
ENGLISH
Contents
2
IMPORTANT (for U.K.Customers)
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an
appropriate safety approved extension lead or consult your
dealer.
If nonetheless the mains plug is cut off, remove the fuse and
dispose of the plug immediately, to avoid a possible shock
hazard by inadvertent connection to the mains supply.
If this product is not provided with a mains plug, or one has to be
fitted, then follow the instructions given below:
IMPORTANT. DO NOT make any connection to the larger
terminal which is marked with the letter E or by the safety earth
symbol | or coloured GREEN or GREEN-and-YELLOW.
The wires in the mains lead on this product are coloured in
accordance with the following code:
BLUE
: NEUTRAL
BROWN : LIVE
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed as
follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
When replacing the fuse only a correctly rated approved type
should be used and be sure to re-fit the fuse cover.
IF IN DOUBT -- CONSULT A COMPETENT ELECTRICIAN.
Obs! nätströmställaren skiljer ej hela apparaten fran nätet.
CAUTION
The product shall not be exposed to dripping or splashing and
that no object filled with liquids, such as vases, shall be placed
on the product.
Do not install this equipment in a confined space such as a
book case or similar unit.
CAUTION Regarding Placement
To maintain proper ventilation, be sure to leave a space
around the unit (from the largest outer dimensions including
projections) equal to, or greater than, shown below.
Left and Right Panels : 5 cm
Rear Panel
: 5 cm
Top Panel
: 20 cm
Thank you for choosing TEAC. Read this manual carefully to get
the best performance from this unit.
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
How to Reset the Settings to the FACTORY DEFAULTS. . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connection (FM antenna) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection (AM antenna). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Speaker Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Positioning of the Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Names of Each Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Speaker Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Dubbing from VIDEO 2 or 3 to VIDEO 1 . . . . . . . . . . . . . . . . . . . . . . . 56
Dubbing the audio and video signals separately . . . . . . . . . . . . . . 56
Surround Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
DOLBY PRO LOGIC II MUSIC parameters . . . . . . . . . . . . . . . . . . . . 68
Dynamic Range Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Preset Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
RDS Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
RDS (EON PTY/EON TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
PTY Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
OSD (On-Screen Display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Code List (Remote Control Unit). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Function Table (Remote Control Unit). . . . . . . . . . . . . . . . . . . . . . . 102
"DTS", "DTS Digital Surround", "DTS-ES Extended Surround"
and "Neo:6" are trademarks of Digital Theater Systems, Inc.
©1996, 2000 Digital Theater Systems, Inc. All rights reserved.
Manufactured under license from Dolby Laboratories. "Dolby",
"Pro Logic" and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992-1997
Dolby Laboratories, Inc. All rights reserved.


background image
FRANÇAIS
ESPAÑOL
Sommaire
Indice
3
ATTENTION
Ne pas exposer l'appareil à l'humidité ou aux projections
d'eau; ne pas poser d'objets contenant de l'eau, tels qu'un
vase, ou un liquide quelconque, sur l'appareil.
Ne pas installer l'appareil dans un endroit clos tel qu'une
bibliothèque ou un meuble fermé.
PRECAUCIÓN
El producto no deberá quedar expuesto a goteos o
salpicaduras, ni servir de base para objetos que contengan
líquido (jarrones, etc.).
No instale este equipo en espacios cerrados tales como
estantes de libros o similares.
Nous vous remercions pour l'achat d'un appareil TEAC. Lire ce
manuel avec attention pour obtenir les meilleures performances
possibles de cet appareil.
Enhorabuena por la adquisición de un TEAC. Lea detenidamente
este manual a fin de obtener el mejor rendimiento de esta
unidad.
Sommaire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Avant utilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Comment réinitialiser les VALEURS PAR DEFAUT REGLES EN USINE
5
Raccordement des antennes (FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Raccordement des antennes (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Raccordements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Raccordement des enceintes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mise en place des enceintes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Noms des commandes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Mise en place des piles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Configuration des enceintes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Fonctionnement de base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Copie de VIDEO 2 ou 3 à VIDEO 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Copie séparée de signaux audio et vidéo . . . . . . . . . . . . . . . . . . . . 57
Mode Surround. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Paramètres DOLBY PRO LOGIC II MUSIC . . . . . . . . . . . . . . . . . . . . 69
Compression de la gamme dynamique. . . . . . . . . . . . . . . . . . . . . . . 71
Syntoniseur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Syntonisation préréglée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Recherche de RDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
RDS (EON PTY/EON TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Programmes PTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
OSD (Affichage sur écran) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Code de réglage (Télécommande) . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Tableau de fonctions (Télécommande) . . . . . . . . . . . . . . . . . . . . . 102
"DTS", "DTS Digital Surround", "DTS-ES Extended Surround" et
"Neo:6" sont des marques déposées de Digital Theater
Systems, Inc. © 1996, 2000 Digital Thater systems, Inc. Tous
droits reservés.
Fabriquer sous license par Dolby Laboratories. "Dolby", "Pro
Logic" et le symbol double D sont des marques déposées de
Dolby Laboratories. Traités confidentiels et non-publiés. ©
1992-1997 Dolby Laboratories, Inc. Tous droits réservés.
"DTS", "DTS Digital Surround", "DTS-ES Extended Surround" y
"Neo:6" son marcas registradas de Digital Theater Systems, Inc.
© 1996, 2000 Digital Theater Systems, Inc. Todos los derechos
reservados.
Fabricado con licencia de Dolby Laboratories. "Dolby", "Pro
Logic" y el símbolo de la doble D son marcas registradas de
Dolby Laboratories. Confidential Unpublished Works. © 1992-
1997 Dolby Laboratories, Inc. Todos los derechos reservados.
Indice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Antes de comenzar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Para restablecer los ajustes originales de fábrica . . . . . . . . . . . . . 5
Conexión (Antena de FM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Conexión (Antena de AM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Conexión . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Conexiones de altavoz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Emplazamiento de los altavoces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Nombres de los controles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Instalación de las pilas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Mando a distancia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Configuración de altavoces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Funcionamiento básico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Copia de VIDEO 2 ó 3 a VIDEO 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Copia de las señales de audio y vídeo por separado . . . . . . . . . . 57
Modo envolvente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Parámetros DOLBY PRO LOGIC II MUSIC . . . . . . . . . . . . . . . . . . . . 69
Compresión del margen dinámico. . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Sintonizador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Presintonías . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Búsqueda RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
RDS (EON PTY/EON TA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Programas PTY (por tipo) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
OSD (menús de pantalla) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Solución de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Especificaciones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Código de configuración (Mando a distancia) . . . . . . . . . . . . . . . . 95
Tabla de funciones (Mando a distancia) . . . . . . . . . . . . . . . . . . . . 102


background image
ENGLISH
Before Use
4
Read this before operation
< As the unit may become warm during operation, always leave
sufficient space around the unit for ventilation.
The ventilation holes should not be covered. Make sure there
is at least 20 cm of space above and at least 5 cm of space on
each side of the unit. Do NOT place anything on top of the unit.
< The voltage supplied to the unit should match the voltage as
printed on the rear panel. If you are in any doubt regarding this
matter, consult an electrician.
< Choose the installation location of your unit carefully. Avoid
placing it in direct sunlight or close to a source of heat. Also
avoid locations subject to vibrations and excessive dust, heat,
cold or moisture.
< Do not place the unit on the amplifier/receiver.
< Do not open the cabinet as this might result in damage to the
circuitry or electrical shock. If a foreign object should get into
the unit, contact your dealer or service company.
< When removing the power plug from the wall outlet, always
pull directly on the plug, never yank the cord.
< Do not attempt to clean the unit with chemical solvents as this
might damage the finish. Use a clean, dry or slightly damp
cloth.
< Keep this manual in a safe place for future reference.
Maintenance
If the surface of the unit gets dirty, wipe with a soft cloth or
use diluted mild liquid soap. Be sure to remove any excess
completely. Do not use thinner, benzine or alcohol as they may
damage the surface of the unit.
How to Reset the Settings to the FACTORY DEFAULTS
Memory Backup
If the power supply is interrupted for 14 days or longer, the
settings kept in memory (such as preset stations and speaker
settings) will be erased.
If you want to manually initialize the settings, press the
STANDBY/ON switch while holding down the MEMORY button.
The unit must be in the standby mode while doing this reset.
All the settings will be reset to the default settings.


background image
FRANÇAIS
ESPAÑOL
5
Avant utilisation
Comment réinitialiser les VALEURS PAR DEFAUT REGLES EN USINE
Lire les consignes suivantes avant toute utilisation
< L'appareil pouvant dégager de la chaleur lorsqu'il fonctionne,
laissez un espace suffisant autour de l'appareil afin de
permettre une ventilation naturelle.
Ne pas obstruer les orifices de ventilation. Laissez au moins 20
cm de libre au-dessus et au moins 5 cm de chaque côté de
l'appareil.
Ne placez RIEN au-dessus de l'appareil.
< La tension d'alimentation utilisée doit être identique à la
tension indiquée sur la plaque à l'arrière de l'appareil. En cas
de doute, n'hésitez pas à consulter un électricien.
< Choisissez soigneusement l'endroit où vous installerez
l'appareil. Evitez de le placer dans un endroit exposé
directement aux rayons solaires ou à proximité d'une source
de chaleur. Evitez également les endroits soumis à des
vibrations ou exposés à la poussière, à la chaleur, au froid et à
l'humidité.
< Ne placez pas l'appareil sur l'amplificateur ou le récepteur.
< N'ouvrez jamais l'appareil pour ne pas endommager les
circuits ou vous exposer à un risque d'électrocution. Au cas
où un objet tomberait par inadvertance dans l'appareil,
contactez votre revendeur ou la société chargée de la
maintenance.
< Pour débrancher le cordon d'alimentation de la prise murale,
tirez directement sur la prise, ne tirez jamais sur le cordon.
< N'essayez pas de nettoyer l'appareil avec un détergent
chimique, vous risqueriez d'abîmer la finition du revêtement.
Utilisez toujours un chiffon propre et sec.
< Conservez soigneusement ce manuel pour pouvoir vous y
référer ultérieurement.
Entretien
Si la surface de l'appareil est sale, nettoyez-la avec un chiffon
doux ou utilisez une solution diluée de savon doux. Veillez à ce
qu'il ne reste pas de produit sur l'appareil. N'utilisez jamais de
diluant, de benzène ou d'alcool, ceux-ci risquant
d'endommager la surface de l'appareil.
Mémoire de secours
Si l'alimentation est interrompue pendant 14 jours ou plus, les
réglages conservés en mémoire (tels que, par exemple les
stations préréglées, les réglages des enceintes) seront effacés.
Si vous souhaitez initialiser les paramètres manuellement,
maintenez la touche MEMORY enfoncée et appuyez sur la touche
STANDBY/ON en mode veille.
Tous les réglages reprendront leur valeur par défaut.
Antes de comenzar
Para restablecer los ajustes originales de fábrica
Léase antes de continuar
< La unidad puede calentarse durante su funcionamiento, por lo
que habrá que dejar espacio suficiente alrededor para su
ventilación.
Los orificios de ventilación no deberán obstruirse. Deje al
menos 20 cm de espacio libre encima de cada unidad y 5 cm
en los laterales.
NO coloque ningún objeto encima de la unidad.
< La tensión suministrada a la unidad deberá coincidir con el
valor indicado en el panel posterior. En caso de duda, consulte
a un electricista.
< Elija cuidadosamente el emplazamiento de la unidad. No
coloque la unidad a la luz solar directa ni cerca de fuentes de
calor. Evite también los lugares expuestos a vibraciones o a un
exceso de suciedad, frío, calor o humedad.
< No coloque la unidad encima del amplificador/receptor.
< No abra la carcasa de la unidad, ya que podrían dañarse los
circuitos o producirse descargas eléctricas. Si entra algún
cuerpo extraño en la unidad, póngase en contacto con su
distribuidor o empresa de servicios.
< Cuando desconecte el cable de la toma mural, sostenga
únicamente el conector y nunca el propio cable.
< No intente limpiar la unidad con disolventes químicos, ya que
podrían dañar el acabado. Utilice un paño limpio y seco.
< Conserve el manual en un lugar seguro para futuras consultas.
Mantenimiento
Si se ensucia la superficie del equipo, pase un paño suave o
utilice jabón líquido normal diluido. Limpie cualquier resto que
pueda quedar en la unidad. No utilice aguarrás, bencina ni
alcohol, ya que podría dañar el acabado de la unidad.
Memoria de seguridad
Si el suministro de corriente se interrumpe durante dos semanas
o más, se borrarán los ajustes almacenados en la memoria (por
ejemplo, presintonías, configuración de altavoces).
Si desea reiniciar manualmente los ajustes, mantenga pulsado el
botón MEMORY y presione STANDBY/ON desde el modo de
espera.
Todos los ajustes restablecerán sus valores estándar.