1
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
MF-WMFS593-147
SERVICE MANUAL
US Model
Canadian Model
WM-FS593/FS595
AEP Model
E Model
WM-FS593
WM-FS593/FS595
RADIO CASSETTE PLAYER
MICROFILM
Photo : WM-FS593
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz (US, Canadian,
Central and South America)
531 - 1,602 kHz (Except US,
Canadian, Central and South America)
Tape section
Frequency response (Dolby NR off)
Playback: 30 - 14,000 Hz
Output
2 (Headphones/earphones) jack
Load impedance 8 - 300 ohms
General
Power requirements
3 V
Two R6 (size AA) batteries
Dimensions (w/h/d)
Approx. 96.5
× 130.6 × 47.8 mm
(3 7/8
× 5 1/4 × 1 15/16 inches) incl.
projecting parts and controls
Mass
Approx. 295 g (10.5 oz) / Approx.
370 g (13.1 oz) incl. batteries and
a cassette
Supplied accessories
Stereo headphones or Stereo
earphones (1)
Belt clip (1)
Flasher (1) (FS595 only)
Sony CR2025 lithium battery (1)
(FS595 only)
Design and specifications are subject to change without
notice.
SPECIFICATIONS
Flexible Circuit Board Repairing
· Keep the temperature of the soldering iron around 270°C during
repairing.
· Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
· Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on Chip Component Replacement
· Never reuse a disconnected chip component.
· Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Dolby noise reduction manufactured under license from Dolby Labo-
ratories Licensing Corporation.
"DOLBY" and the double-D symbol
a are trademarks of Dolby
Laboratories Licensing Corporation. (WM-FS595 only)
Ver 1.3 1999. 06
With SUPPLEMENT-1
(9-924-906-81)
2
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Moisture Resistant Treatment ............................................. 3
2. GENERAL
Getting Started ........................................................................ 6
Operating the Walkman .......................................................... 6
Additional Information ........................................................... 7
3. DISASSEMBLY
3-1. Display Board ..................................................................... 8
3-2. Mechanism Block ............................................................... 8
3-3. Main Board ......................................................................... 9
3-4. Mechanism Deck ................................................................. 9
3-5. Headphone Board .............................................................. 10
3-6. Control Board .................................................................... 10
4. MECHANICAL ADJUSTMENTS ............................ 11
5. ELECTRICAL ADJUSTMENTS ............................. 11
6. DIAGRAMS
6-1. Block Diagram .................................................................. 13
6-2. Printed Wiring Boards Main Section ............................ 15
6-3. Schematic Diagram Main Section ................................. 17
6-4. Printed Wiring Board Display Section .......................... 20
6-5. Schematic Diagram Display Section ............................. 21
6-6. IC Pin Description ............................................................. 24
7. EXPLODED VIEWS
7-1. Cassette Holder Section .................................................... 26
7-2. Rear Cabinet Section ......................................................... 27
7-3. Mechanism Deck Section .................................................. 28
8. ELECTRICAL PARTS LIST ..................................... 29
3
SECTION 1
SERVICE NOTE
1-1. MOISTURE RESISTANT TREATMENT
Be sure to perform the following work when the HOLD knob and
VOL knob have been replaced in servicing:
Apply SONY grease SGL-505 (7-662-010-04) to the HOLD knob
and VOL knob at the points specified in the figure with an applica-
tor or other means.
grease applying
point (rear cabinet)
grease applying
point (HOLD knob)
4
SECTION 2
GENERAL
This section is extracted
from instruction manual.
5