background image
VIDEO GRAPHIC PRINTER
UP-895
UP-895CE
UP-895MD
SERVICE MANUAL
1st Edition


background image
UP-895/(E)
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin
de réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les
réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres.
Pour toute réparation faire appel à une personne compétente uniquement.


background image
1
UP-895/(E)
Table of Contents
1. Operating Instructions
2. Service Information
2-1.
Board Layout ............................................................................................... 2-1
2-2.
Disassembly ................................................................................................ 2-1
2-3.
Removal of Major Parts .............................................................................. 2-2
2-3-1.
Removal of Mechanical Block ................................................... 2-2
2-3-2.
Removal of MA-99 Board ......................................................... 2-3
2-3-3.
Removal of Switching Regulator ............................................... 2-3
2-3-4.
Removal of Thermal Head ......................................................... 2-4
2-4.
Tightening the Screws ................................................................................. 2-5
2-5.
Installation of Fan Motor ............................................................................ 2-6
3. Electrical Alignment
3-1.
AGC Adjustment ......................................................................................... 3-1
3-2.
Video Level Adjustment ............................................................................. 3-1
3-3.
Brightness and Contrast Adjustment ........................................................... 3-2
3-4.
Head Voltage Adjustment ........................................................................... 3-3
3-5.
Initialization of Print Count History ........................................................... 3-3
4. Circuit Operation Description
4-1.
Video Circuit ............................................................................................... 4-3
4-1-1.
BNC Input Connector - Trap Filter Circuit ................................ 4-3
4-1-2.
nC-SYNC Generator Circuit ...................................................... 4-3
4-1-3.
AGC Circuit ............................................................................... 4-3
4-1-4.
Brightness and Contrast Control ................................................ 4-3
4-1-5.
A/D Conversion and D/A Conversion ....................................... 4-3
4-2.
Clock Generator Circuit .............................................................................. 4-4
4-3.
Memory and Head Control Circuit ............................................................. 4-4
4-3-1.
Reading the Serial Data from System Control ........................... 4-5
4-3-2.
Writing in Frame Memory ......................................................... 4-5
4-3-3.
Transfer from Frame Memory to Line Memory ........................ 4-5
4-3-4.
Thermal Head Control and One-Line Memory .......................... 4-5


background image
2
UP-895/(E)
4-4.
System Control Section ............................................................................... 4-8
4-4-1.
Reading of Keys ......................................................................... 4-8
4-4-2.
Reading of Function Switches ................................................... 4-8
4-4-3.
Platen Motor Control .................................................................. 4-9
4-4-4.
Head Up and Down Control ..................................................... 4-10
4-4-5.
Monitor of Door Sensor ........................................................... 4-10
4-4-6.
Monitor of Paper Sensor .......................................................... 4-10
4-4-7.
Monitor of Head Temperature Sensor ...................................... 4-11
4-4-8.
Control of Head Fan Motor (for Head Cooling) ...................... 4-11
4-4-9.
Control of Video Circuit Section ............................................. 4-11
4-4-10. Control of Memory and Head Control Circuit ......................... 4-12
4-4-11. Gamma Correction and Thermal Storage Correction .............. 4-13
4-4-12. Discrimination of Video Signal to be Input ............................. 4-13
4-4-13. Remote Interface ...................................................................... 4-13
4-4-14. Storage of Print Count History ................................................. 4-13
4-5.
Thermal Head Section ............................................................................... 4-14
4-5-1.
Structure ................................................................................... 4-14
4-5-2.
Basic Operation ........................................................................ 4-15
4-5-3.
Stair Generation ....................................................................... 4-15
4-5-4.
Temperature Correction ........................................................... 4-16
4-5-5.
Line Count Correction .............................................................. 4-16
5. Troubleshooting
5-1.
Print is Faulty .............................................................................................. 5-1
5-2.
Print is Too Dark or Too Light ................................................................... 5-2
5-3.
"Paper Sensor" is Out of Order ................................................................... 5-3
5-4.
Head Operation (Up & Down) is Out of Order ........................................... 5-4
5-5.
Paper Feeding is Out of Order .................................................................... 5-5
5-6.
Door (Opening and Closing) is Out of Order .............................................. 5-6
6. Service Mode (Self-diagnostic Function)
6-1
Printing the Test Pattern .............................................................................. 6-1
6-2.
Up/Down Operation of Head ...................................................................... 6-2
6-3.
Feed Operation ............................................................................................ 6-2
6-4.
Display and Clearing of Print Sheet History ............................................... 6-3
7. Semiconductor Pin Assignments


background image
3
UP-895/(E)
8. Spare Parts
8-1.
Notes on Repair Parts .................................................................................. 8-1
8-2.
Exploded Views .......................................................................................... 8-2
8-3.
Electrical Parts List ..................................................................................... 8-7
9. Block Diagram
Overall .................................................................................................................... 9-1
10. Schematic Diagrams and Board Layouts
FRAME ................................................................................................................ 10-2
KY-454 ................................................................................................................. 10-2
SE-531 .................................................................................................................. 10-2
SE-532 .................................................................................................................. 10-2
SU-52 ................................................................................................................... 10-2
MA-99 .................................................................................................................. 10-4